Larson Electronics GAU-HB-12L-LED-WP-WCM User manual

GAU-HB-12L-LED-WP-WCM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
60W High Bay LED Fixture
100-277V AC - Aluminum - Cold Forged - IP65
Instruction Manual
Thank you for your purchase of the Larson Electronics GAU-HB-12L-LED-WP-WCM.
WARNING
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE GAU-HB-12L-LED-WP-WCM MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
The GAU-HB-12L-LED-WP-WCM High Bay LED Fixture from Larson Electronics is designed for industrial work sites and
elevated lighting requirements. The 60-watt fixture operates on 100-277V AC and emits 9,000 lumens of white light during use.
Made out of aluminum with an acrylic lens, the unit caters to Hook, Bracket and Pipe mounting configurations.
MOUNTING
The GAU-HB-12L-LED-WP-WCM features a variety of mounting options: Hook, Bracket and Pipe. For hook
mounting configurations, the LED fixture can hang suspended in the air, via a small eyelet located at the back
of the unit. When secured using a mounting bracket, the configuration offers 180° of rotation. Pipe mounting
configurations are suitable for sturdy support in overhead positions.
HOOK INSTALLATION
1. Make sure the power is disconnected before attempting to install the unit.
2. Screw the circular ring insert tightly into the mounting attachment found on top of the unit.
3. Hang a safety chain on the hook you will be using to secure the unit to the ceiling.
4. Lock the safety chain to the circular ring attachment you connected in Step 2.
5. Finish the wire connection for the unit.

GAU-HB-12L-LED-WP-WCM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
BRACKET INSTALLATION
1. Make sure the power is disconnected before attempting to install the unit.
2. Fix 2 screws into the ceiling 85 mm or 3.15 in apart for the unit to be mounted.
3. Place the unit on the screws and tighten the nuts to the expansion screws.
4. Finish the wire connection for the unit.
MAINTENANCE
Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool downbefore
performing maintenance.
Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will voidthe
warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine
checks to be made on a yearly basis. Frequency of use and environment shoulddetermine this. It is
recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance.
Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e.excessivedust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The GAU-HB-12L-LED-WP-WCM is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.