Larson Electronics EPL-LP-70W-LED-WALL Manual

EPL-LP-70W-LED-WALL
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
EPL-LP-70W-LED-WALL Instruction Guide
Explosion Proof 70 Watt Wall Mount Low Profile LED Light
Thank you for your purchase of the Larson Electronics EPL-LPBS-70LED series LED light. This light is completely
assembled, tested and ready for installation when shipped from the factory. Please follow the steps below in order to
operate and maintain this product.
IMPORTANT
READ CAREFULLY BEFORE OPERATING THIS LIGHT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF UNSURE
ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL. THE EPL-LPBS-70LED
MUST BE OPERATED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER
GROUNDING IS REQUIRED FOR SAFETY.
FOR PERSONAL SAFETY, ALWAYS CONFIRM THE RATING OF ANY KNOWN HAZARDOUS OR POTENTIALLY HAZARDOUS
LOCATION WHERE THE LIGHT IS TO BE USED.
WARNING: OPERATE ONLY AT THE VOLTAGE LISTED ON THE PRODUCT LABEL.
WARNING: TO PREVENT IGNITION OF A HAZARDOUS ATMOSPHERE, THE SUPPLY CIRCUIT SHOULD BE DISCONNECTED
WHEN INSTALLING OR PERFORMING ANY MAINTENANCE ON THIS UNIT.
WARNING: WHEN INSTALLING THIS LIGHT IN HAZARDOUS LOCATIONS, CHECK THE OPERATING TEMPERATURE LIMITS
PRIOR TO INSTALLATION TO BE SURE IT CONFIRMS TO THE ENVIRONMENTAL TEMPERATURE RESTRICTIONS AND NEC
CLASSIFICATIONS. CHECK THE FIXTURE’S METAL NAMEPLATE FOR TEMPERATURE (T) RATINGS.
WARNING: DO NOT SCRATCH OR CHIP THE FRONT LENS. TURN THE POWER OFF BEFORE STARTING INSTALLATION OR
REPAIR.
WARNING: OPERATE THIS FIXTURE ONLY AT THE VOLTAGE OF YOUR SPECIFIC SUPPLY CIRCUIT. FAILURE TO DO SO
WILL RESULT IN DAMAGE TO THE FIXTURE.
WARNING: SUBSTITUTE COMPONENTS MAY IMPAIR EXPLOSION PROOF SAFETY.
INSTALLATION
Before operation, confirm that the power source will provide the correct voltage
indicated on the product nameplate.
Check product nameplate for Ratings and Approvals.
Place the light in the desired location and run its power cord to a power source. Ensure
all safety requirements are followed for the hazardous area. If longer lengths of cables
are required a minimum of 18awg (1.5mm diameter) is required.
General Mounting
For maximum long term reliability and light output, the light must be installed in free air.
For best optical performance Larson Electronics recommends mounting unit at a 45° angle with respect to the vertical
mounting pole or wall.
For maximum long term reliability and light output, the light must be installed in free air.
The Area Light series luminaire fixture design incorporates an over-temperature control circuit that reduces input power
should internal temperatures reach a maximum level. As a result, light output may be reduced.
An internal power-factor-corrected supply allows it to be used from any nominal 100V 277V, 50/60Hz single phase AC
supply without any variation in light output.
Voltage: 100-277V AC 50/60Hz
It is recommended that to ensure moisture does not flow through the cable a loop
in the cord should be implemented where possible during installation. If this is not
practical for the install than necessary precautions should be taken to prevent
moisture entering the conduit thus entering the fixture.
Recommended mounting height: 8 feet to 24 feet (2.4 m to 7.3 m)
WIRE(AC) WIRE(DC) COLOURED CABLE
AC LIVE
DC LIVE
BLACK
AC NEUTRAL
DCNEUTRAL
WHITE
GROUND
GROUND
GREEN

EPL-LP-70W-LED-WALL
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
ADJUSTMENT
The Area Light series luminaire fixture is equipped with “L” and “U” brackets on Luminaire from factory. Once fixture is
mounted, loosen the four M8 bolts connecting the “U” bracket to the “L” bracket, enough to allow the bracket to pivot.
Position bracket to desired orientation. Torque all bracket hardware to 6 ft-lbs.
This light is instant-on and will illuminate once energized.
MAINTENANCE
To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing maintenance.
WARNING:
Risk of electric shock. Removal of the lens will void the warranty.
Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine checks to be made on
a yearly basis. Frequency of use and environment should determine this. It is recommended to follow an Electrical
Preventive Maintenance Program as described in NFPA 70B: Recommended Practice for Electrical Equipment.
The lens should be cleaned periodically as needed to ensure continued photometric performance. Clean the lens with a
damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid cleaner.
Do not operate if the lens is cracked or damaged. All fasteners should be properly seated
This LED Luminaire should require a minimum amount of maintenance. If any unforeseen repairs are required then
always observe explosion protection regulations and requirements.
WARNING:
This LED Luminaire should not require any electrical maintenance. Never open the luminaire (other than the junction
box lid if supplied); there are no user- serviceable parts inside.
Inspection
Within the scope of a maintenance or inspection routine the following should be included: protective hoses covering the
connection cables. Cable entries must be free of corrosion. Perform visual mechanical and electrical inspections on a
regular basis. We recommend routine checks to be made on a yearly basis. Frequency of use and environment should
determine this. It is recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended Practice for Electrical Equipment
The lens should be cleaned periodically, as needed, to ensure continued photometric performance. Clean the lens with
a damp, non-abrasive, and lint- free cloth. If not sufficient, use mild soap or a liquid cleaner. Do not use and abrasive,
strong alkaline, or acid cleaners as damage may occur.
Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e. excessive
dust build-up). Clean with a non-abrasive, damp cloth, if needed.
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire
shall be replaced.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR
INSTALLATION REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE
REQUIRED, PLEASE CONTACT LARSON ELECTRONICS AT
1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.