Larson Electronics LEDWL-STRB-RED-1227 User manual

LEDWL-STRB-RED-1227
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
1 of 3
25W Red LED Warning Spotlight
2250 Lumens - 120-240V AC - Red Strobing Safety Light - IP67
Instruction Manual
Thank you for your purchase of the Larson Electronics LEDWL-STRB-RED-1227.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDWL-STRB-RED-1227 MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OFTHIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OFTHIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES ORDEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BEREPLACED BEFORE RESUMING USE.
The LEDWL-STRB-RED-1227 from Larson Electronics is a Warning and Indicator Strobing LED Spotlight that is designed to provide a
warning to workers and pedestrians of hazards or to indicate other work area or environmental situations. This ultra compact red LED
light produces a 2,250 lumen output with low amp draw and a 50,000 hour service life. Additionally, the LEDWL-STRB-RED-1227
features an external power source that allows the warning light to operate on 120-240V AC and have the ability to strobe. This provides
operators with a versatile and powerful warning and indicator safety light.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas where
weatherproofing may be required. Universal voltage driver permits operation at 120V - 240V AC.
WARNINGS
To preventserious damage to eyesight, never lookinto spotlight when light is on. DO NOT shine light intothe face ofsomeone
else.
DO NOT touchlensofspotlightwhenlightis on or if it was recently on. The lens will be hot and could cause burns.
DO NOT use this product for other than its intended use.
DO NOT operate in close proximity of Combustible or flammable materials.
DO NOT attempt to operate this light if cord, lens, bulb or any part of the light is damaged or corroded.

LEDWL-STRB-RED-1227
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
2of 3
The LEDWL-STRB-RED-1227 LED warning/indicator strobing spotlight is equipped with Deustch connector and a 20` wiring harness.
The external power supply is remote mountable. Operators can install the power supply between the light and the control station. The
external power supply is designed to be hardwired and operates on voltages ranging from 120-240V AC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Standard Cord Cap
This unit comes pre-wired from factory with the selected cord cap. Take
precautionary steps for weatherproofing all connections if installed in a
location where water may come in contact with the unit. All outdoor
installations and indoor installations near a wet location require the use of a
GFCI device for safety, according to the National Electrical Code® (NEC).
Ensure the unit is properly grounded.
DETACHABLE CORDS
•Cord is attached via a weatherproof 2-pin Deutsch connector.
•The cord is detachable by depressing the tab on the top of the connectors. This enables the
operator to remove and store the light while leaving the cord connected to the power source.
•Additional or replacement cords can be ordered from our website. Contact us or visit LarsonElectronics.com for more
information.
PIVOT
ADJUSTMENT
BOLT
TIGHTENING BOLT
FIGURE 1
MOUNTING AND ADJUSTMENTS:
The LEDWL-STRB is suspendedwithin a form fitting trunnion
(yolk-type) mount. This trunnionmount allows the LED light to
be adjusted into any position once mounted.Simply loosen
the Pivot Adjustment Bolt shown in FIGURE 1, angle, and
tighten once desired position is achieved.
A single stainless steel tightening bolt protrudesfrom the
mount, enabling the operatorto install thelight usinga single
through-hole.
This LED warning spotlight comes in a variety of output
colors from factory. Colors shown in this manual may vary.

LEDWL-STRB-RED-1227
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
3of 3
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The LEDWL-STRB-RED-1227 is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.