Laser Technology TruPulse 200 User manual

TruPulse®Quick
Reference Field Guides
TruPulse®Models: 200, 200 B, 360, 360 B and 360 R
Authorized Distributor

LTI Technical Support:
Toll Free: 1.877.696.2584
Phone: [phone]
Email: [email protected]
Web: www.lasertech.com
LTI Hours of Operation:
Monday through Friday
8:00 am to 5:00 pm (MST)
(Excluding Holidays)
LTI Corporate Headquarters:
6912 South Quentin Street
Centennial, CO 80112 USA
LTI YouTube®Channel:
www.youtube.com/lasertechpro
for TruPulse®Training Videos
TruPulse®200/B, 360/B
Fire Button
Down Button
Up Button
Fire Button
Down Button
Up Button
TruPulse®360 R

Measured by TruPulse:
Calculated by TruPulse:
= Horizontal Distance
= Slope Distance
= Vertical Distance
= Height
= Inclination
= Azimuth (360 models)
= Missing Line
= Fire Button
= Up Button
= Down Button
( ) = In-scope Top
( ) = In-scope Bottom
1-Shot HD Mode: 2-Shot Missing Line:
2-Shot Height: 3-Shot Height:
TruPulse®Values & Key Code:

[1] Press-and-hold ( ), then press .
[2] Press to scroll through ( ) and press to choose.
[3] Press to scroll through ( ) and press to choose.
[1] Press-and-hold ( ), then press again ( ).
[2] Press , then press to scroll through ( ) ( ).
[3] Press to choose.
For Standard Mode, press-and-hold ( ), then press .
For Filter Mode, press-and-hold ( ),press ( ), then press .
For Farthest Mode, press-and-hold ( ),press twice ( ),
then press . For Closest Mode, press-and-hold ( ), press twice
( ), then press . For Continuous Mode, press-and-hold ( ),
press ( ), then press .
Change Units of Measurement:
Turn On or Off Bluetooth® (Models 200B, 360B/R):
Change Targeting Mode:

6 in (15 cm) minimum: Metal rim glasses, pen/pencil, metal watch band, pocket
knife, metal zipper/buttons, belt buckle, batteries, binoculars, cell
phone, keys, camera, camcorder, survey nails, metal tape measure.
18 in (50 cm) minimum: Clipboard, data collector, computer, GPS antenna,
2-way radio, hand gun, hatchet, cell phone case with magnetic closure.
6 ft (2 m) minimum: Bicycle, re hydrant, road signs, sewer cap or drain, steel
pole, ATV, guy wire, magnets, chain-link fence, bar-wire fence, data
collectors that use a magnet to hold the stylus.
15 ft (5 m) minimum: Electrical box, small car/truck, powerline, building with
concrete & steel.
30 ft (10 m) minimum: Large truck, metal building, heavy machinery.
Required Clearances from TruPulse®Compass:
When ring the TruPulse 360, please maintain a safe clearance of:

[1] Always recalibrate your compass when ( ) ashes.
[2] If calibration fails repeatedly, perform the tilt calibration then repeat steps.
Calibrate the Compass (Models 360/B/R):
Always perform outside, away from magnetic interference
and face towards Magnetic North.
Helpful Tips:
[1] Press-and-hold ( ), press until ( )
[2] Press ( ), press ( ), press .
[3] ( )( ), press ( )( ), press .
[4] Face North ( ), hold in position 1, press ( ).
[5] Hold in position 2, press ( ), hold in position 3.
[6] Press ( ), hold in position 4, press ( ).
[7] Hold in position 5, press ( ), hold in position 6.
[8] Press ( ), hold in position 7, press ( ).
[9] Hold in position 8, press . If ( ), press and
repeat steps 4 through 8. If ( ), press ( ).
[2]
[5][1]
[3]
[8]
[7]
[6]
[4]

Calibrate the Tilt Sensor (Models 360/B/R):
[1] Press-and-hold ( ), press until ( ).
[2] Press ( )( ), press ( )( ), press .
[3] ( ), hold in position 1, press ( ).
[4] Hold in position 2, press ( ).
[5] Hold in position 3, press ( ).
[Hang 360 R buttons over an edge and press .]
[6] Hold in position 4, press ( ).
[7] Hold in position 5, press ( ).
[8] Hold in position 6, press ( ).
[9] Hold in position 7, press ( ).
[10] Hold in position 8, press .
If ( ), press and repeat steps 3 through 10.
If ( ), press ( ).
[2]
[5]
Always perform on a at, fairly level surface. For the
TruPulse 360 R, you will need to use the edge of a
surface to access the buttons in position 3.
[1]
[3]
[8]
[7]
[6]
[4]

[1] To achieve 1 ft (30 cm)
distance accuracy, hold down
until a decimal point
displays. [2] To shoot through
brush, use the lter mode,
foliage lter and a reector.
[1] Press until ( ).
[2] Aim at target where you have a clear line of sight
then press-and-hold ( ).
[3] Press to scroll through ( ).
Measure Distance:
In HD Mode, it will automatically measure SD, INC
and AZ* then calculate VD and HD. It outputs all the
values via serial and/or Bluetooth® (Models B & R only).
Measurements are from the center of laser to target.
Calibrate the Tilt Sensor (Models 200/B):
Always perform on a at, fairly level surface.
[1] Press-and-hold ( ), press until ( ).
[2] Press ( ), press ( ), press .
[3] ( ), hold in position 1, press ( ).
[4] Rotate 180º to position 2, then press ( ).
[5] Press ( ).
*For TruPulse 360/B/R models only
Helpful Tips:
[1] [2]

Measure Height in 3-Shots:
This routine is ideal for at, vertical objects
that do not lean. To shoot through brush, use
the lter mode, foliage lter and a reector.
[1] Press until ( ) and ( ) ashes.
[2] Aim anywhere you have a clear line of sight and
press-and-hold ( ).
[3] ( ) Aim to top, then press-and-hold .
[4] ( ) ( ) Aim to bottom, press-and-
hold , ( ) ( ).
Measure Height in 2-Shots:
[1] Press until ( ), aim at top of target then
press-and-hold ( )t. Note value.
[2] Aim at the bottom of the target then press-and-hold
( )b. Note value and HT = VDt - VDb.
The 2-shot HT works well on
leaning objects but requires a
clear line of sight for both shots.
Helpful Tip:

Measure Missing Line (Models 360/B/R):
Position yourself anywhere you have a clear line of
site to your two targets.
Measure Missing Line (Models 200/B):
Follow the same steps above. You need to position
yourself where shot 1 and 2 are made looking in
the same direction with a clear line of site to both
targets. The exception is the VD solution will
always be accurate no matter which direction shot
1 and 2 are taken.
[1] Press until ( ) and ( ) ashes.
[2] Aim at the 1st target, press-and-hold ( ).
[3] ( ) Aim at 2nd target, press-and-hold ( ).
[4] ( ), keep pressing to scroll through
( ) from shot 1 to shot 2.