Laser Technology TruPulse 200X User manual

TruPulse®200X
Quick Reference
Field Guide
LTI Part #0144893

LTI Technical Support:
Toll Free: 1.877.696.2584
Phone: [phone]
Email: [email protected]
Web: www.lasertech.com
LTI Hours of Operation:
Monday through Friday
8:00 am to 5:00 pm (MST)
(Excluding Holidays)
LTI Corporate Headquarters:
6912 South Quentin Street
Centennial, CO 80112 USA
LTI YouTube®Channel:
www.youtube.com/lasertechpro
for TruPulse®Training Videos
TruPulse®200X
Fire Button
Back Button
Forward Button Mode Button

TruPulse®200X
Display Indicators:
Inclination
Horizontal
Distance
Vertical
Distance
Closest
Slope
Distance
Farthest
Missing Line
Height
Continuous
Laser Status
Battery Life
Feet
Meters
Yards
Degrees
Percent
Filter
Upper and Lower
Main Display
( )
Cross hair /Aiming Point
Inches
Centimeters
Gate

Measured by TruPulse:
1-Shot Distance: 2-Shot Missing Line:
2-Shot Height: 3-Shot Height:
TruPulse®200X Values & Key Code:
= Horizontal Distance
= Slope Distance
= Vertical Distance
= Height
= Inclination
= Missing Line
= Fire Button
= Mode Button
= Forward Button
= BackButton
( ) = In-scope Top
( ) = In-scope Bottom
Calculated by TruPulse:

Change Display Brightness Level:
Change Units of Measurements:
[1] Press until ( ). [2] Press until desired brightness level
( ). [3] Press ( )to accept the brightness level.
[1] Press until ( ).
[2] Press to scroll through unit options ( ), ( ).
[3] Press to accept the units of measurement ( ).
Helpful Tip:
The default units of measurements are meters, centimeters and degrees.

Filter Mode:
Continuous Mode:
[1] Press until ( ). [2] Press to choose ( )
or ( ). [3] Press to accept selection.
[1] Press until ( ). [2] Press to choose ( )or ( ).
[3] Press to accept selection.
When Filter mode is ON, make sure you have the foliage lter attached to the
receive lens and that you are shooting to a reective target.
Helpful Tip:

Targeting Mode:
[1] Press until ( ). [2] Press to choose mode:
Standard ( ); Farthest ( ); Closest ( ).
[3] Press to accept selection.
Helpful Tips:
[1] Targeting mode is not accessible when lter mode is on.
[2] Filter symbol , continuous mode symbol and any other mode symbol will
show on right side of the main display ( )when activated.

[1] The minimum gate values are 1 meter, 4 feet and 2 yards. The maximum gate
values are 500 meters, 1640 feet and 500 yards.
[2] To increase gate value when gate is already on, press until ( )
then press again to change increments.
Helpful Tips:
Gate Function:
In this mode, the TruPulse 200X will only acquire targets beyond the
selected gate value.
[1] Press until ( ). [2] Press to choose on ( )
or off ( ).[3] With Gate ON, press to change the value.
[4] Press and release to increase value by increments of one ( ).
Hold down to increment quickly. [5] Press to set gate.

[1] Press until ( ). [2] Press to choose Bluetooth on ( ),
off ( )or EnC ( ). [3] Press to accept selection.
Turn On or Off Bluetooth®:
[1] Each time the TP200X is powered ON, it will retain the same settings that were
last set/used.
[2] To perform a factory reset, simultaneously press-and-hold the , , and
for approximately 5 seconds. The instrument will power off.
Helpful Tips:

Measure Distance:
In HD Mode, it will automatically
measure SD and INC, then calculate
VD and HD. The values will output
via serial and/or Bluetooth.
Measurements are from the center
of laser to target.
[1] Press until ( ) is displayed. [2] Aim at target where you have
a clear line of sight then long press ( ).
[3] Press to scroll through SD ( ), VD and INC.