Laser 5078 User manual

www.lasertools.co.ukwww.lasertools.co.uk
Instructions
This two piece ramp set can be used as a standard
car ramp or as a pair of access ramps for ATV’s
lawnmowers | motorcycles | mobility scooters | etc.
Load capacity 800kg per ramp (folded)
260kg per ramp (extended)
Height range (extended) 550mm - 1000mm
Steel construction
Safety chains
Carrying handles
5078
Multi-Purpose Folding Ramps
2 Piece Set
Distributed by The Tool Connection Ltd
Kineton Road, Southam, Warwickshire CV47 0DR
T [phone] F [phone]
[e-mail] www.toolconnection.co.uk
If this product fails through faulty materials or workmanship,
contact our service department direct on: [phone].
Normal wear and tear are excluded as are consumable items
and abuse.
Guarantee

Multi-purpose Folding Ramps Operation Instruction
Safety Warning
Assembly
Position Maximum Load (lbs per ramp) Maximum Load (kgs per ramp)
Folded Position 1,764lbs per ramp 800kgs
Extended 573lbs per ramp 260kgs
These multi-purpose folding ramps are designed to simplify the loading and unloading of ATVs as well
as motorcycles, lawn mowers, cement mixers and other plant with the ramps extended. They are NOT
designed to support the weight of a vehicle when the ramps are extended. Load vehicles onto ramps
ONLY when ramps are in the folded positions.
1. Read all instructions prior to use
2. Do not exceed the maximum weight per ramp 800kgs
3. Use only on hard services (concrete)
4. Centre load between the sides of the ramp
5. Maximum tyre width is 230mm (9")
6. Only use ramps central to one side of vehicle or simultaneously at equal distance from sides of
vehicle
7. Do not use with any other lifting equipment
8. A third party should be available to judge the loading procedure
9. Proceed slowly and continuously up the ramps (Do not accelerate or brake suddenly)
10. Check ramps are secure before proceeding
11. Check tailgate of vehicle for maximum load capacity
12. Always inspect the ramps prior and after use and do not use if damaged.
13. Keep ramps dry, clean and free from oil or grease.
14. To not attempt to modify, repair or extend these ramps in any way what so ever.
15. Do not exceed maximum height of 1.2m (40")
16. Keep fingers away from folding parts when opening or closing
17. Protect the tail gate of your vehicle before resting ramp to avoid damage to paintwork.
Part Description Quantity
1 Folding ramp with carrying strap 2
2 Angle ramp with safety chains 2
3 Tyre stop 2
4 Bolt and lock nut M10 x 20mm 8
5 Bolt, nut and washer M8 x 35mm 4
6 Bolt, nut and washer M8 x 20mm 4
7 Bolt and washer M8 x 16mm 4
8 Bolt, nut and washer M6 x 16mm 2
Step 1
Remove each ramp from packaging using
the handle
Step 2
Open the first section of ramp and bolt
together angled section using 4 bolts
per ramp (4)
Always ensure the flange is on the
underside (it is not a tyre guide)
See figures 1, 2, and 3.
Step 3
To use folded as a twin ramp for vehicle
repair, remove the stopping block located
inside the folded sections and insert at the
end of the ramp as shown
See inset picture
Before using as a vehicle ramp ensure the
brakes are applied and chocks are used to
secure wheels
Step 4
To use as a ramp for ATVs, mowers,
cement mixers etc; remove the
stopping block and unfold the
2 sections as shown, fixing the
anchor chains as required.
Parts list
1
2
3
4
550mm to 1000mm
maximum height