LaserPegs National Geographic Oceans User manual

Please read this manual before you begin!
Failure to follow this manual’s instructions may
result in damage to the Triangle Power Base, AC
Adapter and/or Laser Pegs®. Not adhering to
these instructions will void the manufacturer’s
warranty. The packaging must be kept because
it contains important information.
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. © Copyright 2014 All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: [email protected]om
Compatible with other construction kits
Each Laser Peg® is color coded on the circuit board inside
each shape. There is No LED In The 90 Degree Peg.
www.LaserPegs.com
Color
Code
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 yrs.
Do not submerge in water.
All additional model instructions can
be downloaded at www.LaserPegs.com
MODEL INSTRUCTIONS
Construction Compatible
Laser Pegs®link that
allows you to connect to
other construction kits.
Laser Pegs
®
Stackable
EN71, RoHS COMPLIANT
This product complies to
all safety requirements
of ASTM F 963
LIGHT UP
CONSTRUCTION SET INCLUDES:
• 10 Laser Pegs®
• 62 Construction Parts
- Laser Pegs® Peg Cord
• Triangle Power Base
• Instruction Manual
Requires 3-AA Batteries
Batteries NOT
Included
Laser Pegs® Parts List
Construction Parts List
6 Models+
ANY CREATION YOU CAN BUILD
There is No LED In The 90 Degree Peg
x2
x4
x2
x3
x2
x2
x4
x4
x2
x2
x2
x2
STACKABLE x4
x6
SQUARE
PEG x1
HALF-O
PEG x2
x3
x2
x2
x2
x2
x2
x2
90° PEG x2 Y PEG x1
x2
x2
x2
x2
x2
Copyright 2014 © All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
www.LaserPegs.com
Laser Pegs® CARES
Questions? Comments?
For additional compliance info:
1-866-432-3735
Contact: Suppor[email protected]
To construct with Laser Pegs®, slide two pieces together to form a
connection. Slide each piece on and o smoothly. The 90° Pegs are
essential to construction but they DO NOT LIGHT UP.
Connecting Pegs
WARNING! Each Laser Peg® draws current from the batteries. Therefore, the more
pegs you use, the quicker you will deplete your battery power! As the power
weakens, the current will slowly fail and some Laser Pegs® will illuminate (typically
the reds and yellows) and some won’t. When the Laser Pegs® dim the Laser Pegs®
are not broken, they just need stronger batteries or an AC Adapter.
You have 3 simple options...
1. Use a 5-volt AC Adapter –available from www.LaserPegs.com
2. Change the batteries.
3. Use high quality batteries. They will last a little longer, but they will still deplete
rapidly the more laser pegs you connect!
Using an
AC Adapter
Remove all batteries
from Laser Pegs® power
base before using the
5-volt AC adapter.
When using an AC
Adapter, NEVER
place the adapter
plug into the Tri-
angle Power Base
top peg holes.
*To avoid short-circuits, keep metal objects and
other unauthorized materials from obstructing
the peg holes.
The AC adapter and the Triangle Power Base are to be regularly examined for
damage to the cord, plug, enclosure and other parts, and in the event of such
damage, they must not be used until the damage has been repaired.
Never connect more than 200
Laser Pegs® when using a 5-volt
(2000mA) AC Adapter.
Please dispose of batteries properly as per state and local regulations.
1. Remove the three (3) screws.
2. Place three (3) AA batteries in the correct
position - as displayed inside the Triangle
Power Base.
3. Reassemble the Triangle Power Base.
4. Replace the three (3) screws.
5. Push RED Power Button to turn on!
6. Do not mix old and new batteries.
7. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium,
NiMH) batteries!
8. Exhausted batteries are to be removed
from the Triangle Power Base.
9. Never connect more than 200 Laser Pegs®
10. Non-rechargeable batteries are not to be
recharged.
11. Rechargeable batteries are only to be
recharged under adult supervision.
12. Rechargeable batteries are to be removed
from the toy before being recharged.
13. Batteries are to be inserted with the
correct polarity.
14. The supply terminals are not to be short-
circuited.
15. DO NOT THROW BATTERIES INTO FIRE!
Replacing Batteries
Environmental Phenomena
* The unit may malfunction if subjected to radio-frequency interference. It SHOULD revert to
normal operation when the interference stops. If not, it may become necessary to turn the power
o and back on, or remove and reinstall the batteries.
* In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory,
requiring the user to reset the devise by removing and reinstalling the batteries.
WARNING: STROBE LIGHTS
MAY CAUSE SEIZURES
DO NOT SUBMERGE IN WATER
Remove the 3 Phillips head screws
3-AA Batteries
Remove the three Phillips head
screws with a 4mm screw driver.
Requires (3AA) Batteries
OCEANS
Laser Pegs®
Peg Cord
Ages 5 +
Red
Power Button
SOUND/ON/FLASH/FLASH FASTER
Peg Holes
AC Adapter
Connection
Push Red
Power Button
to turn on/o
Push Red Power Button to
cycle through 4 dierent
light settings.
Sound Activated
Triangle Power Base
Model
Diculty
Level
HAMMERHEAD SHARK
2
STEP
3
STEP
4
STEP
FLIP
5
STEP
6
STEP
7
STEP
FLIP
HAMMERHEAD SHARK: Thanks to their attened, hammer-shaped heads, the eyes and nostrils of hammerhead sharks are spaced much
farther apart than those on other shark species. This special setup may give hammerheads an extra-wide eld of view and keen sense of
smell. Like the skin of humans, hammerhead skin changes color when it is exposed to a lot of sunlight.
1
STEP

Copyright 2014 © All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
www.LaserPegs.com
MADE IN CHINA
© 2014 National Geographic Society kids.nationalgeographic.com
8
STEP
9
STEP
11
STEP
12
STEP
13
STEP
15
STEP
16
STEP
17
STEP
18
STEP
19
STEP
20
STEP
21
STEP
22
STEP
23
STEP
10
STEP
14
STEP

Copyright 2014 © All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
www.LaserPegs.com
NATIONAL GEOGRAPHIC KIDS and Yellow Border Design are trademarks of
the National Geographic Society, used under license. All rights reserved.
MADE IN CHINA
ATTACH THE MODEL TO THE TRIANGLE
POWER BASE WITH THE PEG CORD
25
STEP
24
STEP