Laserworld CS-400RGY User manual

CS-400RGY
USER MANUAL
Please read this manual carefully before use!

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
2
of
9
I
Table of contents
Page
1. SAFETY INSTRUCTIONS 3
2. OPERATING DETERMINATIONS 4
3. OPERATION 5
4. AUTO- MUSIC-MODE 5
5. OPERATION WITH DMX 5
6. ILDA OPERATION 7
7. MAINTENANCE 8
8. TECHNICAL SPECIFICATIONS 8
hecking Parts
Please check if the followin parts are included:
1 x CS-400RGY Laser
1 x Power cable
1 x DMX cable
1 x ILDA adaptor
1 x User manual

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
3
of
9
DANGER LASER RADIATION!
Avoid direct eye exposure!
Laser radiation can cause eye dama e and/or skin dama e
All protective measures for a safe operation of this laser must be applied.
1. SAFETY INSTRUCTIONS
- If the device has been exposed to drastic temperature fluctuation, do not
switch it on immediately. The arisin condensation water mi ht dama e your
device. Leave the device switched off until it has reached room temperature.
1. The laser must only be used for shows. The operation is only allowed if it is
controlled by a skilled and well-trained operator.
- Never leave this device runnin unattended and keep it away from children
and unauthorized persons.
2. Keep away from heaters and other heatin sources. In order to safe uard
sufficient ventilation, leave 50 cm of free space around the device.
3. Never direct the laser beam to people or animals.
4. CAUTION LASER DIODE: Never unscrew the housin !
There are no serviceable parts inside the device. Maintenance and service
operations shall only be carried out by authorized dealers.
5. Always disconnect from the mains when the device is not in use or before
cleanin it.
- HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
4
of
9
2. OPERATING DETERMINATIONS
6. The operator has to make sure that laser radiation – also reflected laser
radiation –hi her than the hi hest allowed level is avoided by technical or
or anisational measures.
7. Make sure that the used volta e is : AC 220V~240V, 50/60Hz
8. If the device is used in a flyin installation, the mountin brackets and an
appropriate safety-rope must be fixed.
9. Laser effects are not desi ned for permanent operation. Consistent operation
breaks will ensure that the device will serve you for a lon time without
defects.
10.In some countries, the operator must notify the accidence insurance and the
authority for industrial safety, before operatin a laser. For more information,
contact the relevant authorities.
11.Please consider that unauthorized modifications on the device are forbidden
due to safety reasons!
12.If this device will be operated in any way differently than described in this
manual, the product may suffer dama es and the uarantee becomes void.
Furthermore, any other operation may lead to dan ers like short-circuit,
burns, electric shock, etc.
13.When the laser is not attached to an ILDA output device (even for a short
period), switch ILDA mode off (see below), or turn the device off.

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
5
of
9
3. OPERATION
Please note: for sound/DMX mode the two switches on the back
of the device labelled “BLANKING” and “X/Y” have to be up.
When both switches are down the device can be controlled by
an ILDA output (such as our USB-Box). Use this switch setting
only when connected to such an ILDA controller. Even if you
disconnect/interrupt the ILDA connection only for a short
period, always put the switches into up position, or turn the
device off!
4. AUTO- MUSIC-MODE
If you put switch 10 to “ON” the patterns will chan e automatically, and are
animated by sound (sound or music mode), the switches labelled “BLANKING” and
“X/Y” have to be up. You can control the music-sensitivity of the microphone with
the min-max knob on the rear panel. With switch 1 you can select two modes:
standard sound mode (patterns will move tri ered by sound), and animated sound
mode (patterns will move slowly without sound and will be accelerated with sound).
5. OPERATION WITH DMX
If you turn switch 10 to “OFF”, and switches “BLANKING” and “X/Y” up, the device is
in DMX mode. Set the DMX address and connect the device to a DMX controller, you
can then operate you CS-200G ECO with DMX.
Set the DMX address code with the binary system “0” or “1”. A few examples:
DMX-
adress
DMX-
adress
1 65
17 113
33 161

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
6
of
9
The device uses 13 channels, so if you set the first on DMX address “1” the second
should be DMX address “14” and so on.
The DMX channels are as followin :
channel Function
1 Mode: 0-69 laser off; 70--139 sound mode; 140-
209 animated sound mode (see above); 210-
255 DMX mode
2 Pattern
3 Effect channel: Strobe
4 Vertical movement: analogous to hor. movem.
5 Horizontal movement: 0 no effect; 1-167 (fixed)
movement; 168-188 animated movement left to
right with increasing speed; 189-209 do. Right
to left; 210-255 do. left to right and back
6 Zoom: 0-10 no effect; 11-104 increasing size;
105-154 growing with increasing speed; 155-
204 do. shrinking; 205-255 do.
growing/shrinking
7 Mirroring Y (rotation about y): 0-150 fixed
rotation; 151-255 automatic rotation with incr.
speed
8 Mirroring X (rot. About X): analogous to width
9 Rotation: 0-180 fixed rotation; 181-217
automatic with incr. speed clockwise; 218-255
do. ounter clockwise
10 Blanking: 0-70 no effect; 71-139 points are
brighter; 140-209 dashed lines; 210-255 points
only
11 Waveeffect
12 olor choice:
•0-19 yellow
•20-37 red
•38-56 green
•57-75 gelb
•76-94 rainbow statically
•95-113 rainbow moving
13 Object partly draw
Beginning – end ; Vary - shorten

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
7
of
9
Please note that according to the pattern, not all effect channels are
activated. E. . you can’t zoom dynamic patterns, etc.
Channel 3 (strobe) is also available when in soundmode (channel 1 70-209).
6. ILDA OPERATION
Connect the laser to an ILDA output (as our USB-box) usin the adaptor shipped
with the device, switches “BLANKING” and “X/Y” on the back of the laser have to be
down. You can now operate the laser with ILDA.
Use this switch setting only when connected to an ILDA
controller. Even if you disconnect/interrupt the IDLA connection
only for a short period, always put the switches into up position,
or turn the device off.
You can now control laser output with a PC, usin for example our ShowEditor 2006
software. Laserworld offers a variety of music synchronous lasershows for
ShowEditor 2006.

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
8
of
9
7. MAINTENAN E
Maintenance should be performed every 15-day period, by usin a spon e which is
dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the
mirror.
Always disconnect from the mains when the device is not in use or before cleanin it.
There are no serviceable parts inside the device. Maintenance and service operations
are only to be carried out by authorized dealers.
Never look directly into the light source.
Always disconnect from the mains when the device is not in use or before
cleaning it.
8. TECHNICAL SPECIFICATIONS
Power supply: 110~240AC
DMX 512: 13 channels
Power consumption: 120 W
Working mode: ILDA, DMX 512, Live Play @ Music (sound controlled programmes)
Optical power: ca. 350-420mW / 532nm
Laser classification: 3b
Weight: 4 k
Dimensions: 330 x 285 x 160 mm (L x W x H)
PLEASE NOTE
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and warnin notes written in this user manual.
Laserworld cannot be made liable for dama es caused by incorrect installations and
unskilled operation!

USER MANUAL: Laserworld CS-400RGY
Date: 01/2008
Pa e
9
of
9
EU- Declaration of onformity
We hereby confirm that the followin device
Laserworld S-400RGY
complies with the essential safety requirements, laid down in the re ulations of the
committee to assimilate the provisions of law of all participatin EU states on the
electroma netic compatibility (98/336/EWG).
The device has been classified considerin the followin EU-norms on
electroma netic compatibility:
DIN EN 55103-1: 1996
DIN EN 55103-2: 1996
DIN EN 61000-3-2:2000 + A2: 2005
DIN EN 61000-3-3:1995 + A1: 2001
Assessment of compliance of the product with the requirements relatin to the Low Volta e
Directive (LVD) was based on the followin standards:
DIN EN 60065 : 2002
Furthermore, the device is verified in correspondence to the laser class re ulations DIN EN
60825-1, if properly set up accordin to the upper mentioned laser safety re ulation.
After installin the device, an inspection and official approval is indispensable for the overall
setup. The inspection must follow the european uidelines EN 60825-1 and correspondin
re ulations for the prevention of accidents BGV-B2.
This declaration is executed on behalf of the CS-400RGY Laser manufacturer.
Laserworld (Switzerland) AG
Oberstrasse 1
8274 Tä erwilen
SWITZERLAND
Authorized person:
Supervisory board Ms Rhea Gössel
place of business: 8274 Tä erwilen / SWITZERLAND
company number: CH-440.3.020.548-6
Commercial Re istry Kanton Thur au
www.laserworld.com
[e-mail]
representative accordin to EMVG:
Cleantech Europe GmbH
Mana in Director: Thomas Schulze
Fürkhofstr. 5
81927 München / DE