Laserworld Pure Micro Series User manual

Manual / Bedienungsanleitung
Pure Micro Series
Please read this manual carefully prior to product operation!
Bitte lesen Sie diese Bedienungsanleitung vor Inbetriebnahme des Produkts!
rev. 11/2013
English
Deutsch
SwissLas

Manual: Pure Micro Series
page 2 / 20
Rechtlicher Hinweis:
Die Firma Laserworld (Switzerland) AG behält
sich das Recht vor, Änderungen an ihren Pro-
dukten vorzunehmen, die der technischen
Weiterentwicklung dienen. Diese Änderun-
gen werden nicht notwendigerweise in je-
dem Einzelfall dokumentiert.
Diese Betriebsanleitung und die darin ent-
haltenen Informationen wurden mit der ge-
botenen Sorgfalt zusammengestellt. Die Fir-
ma Laserworld AG übernimmt jedoch keine
Gewähr für Druckfehler, andere Fehler oder
daraus entstehende Schäden.
Die in dieser Bedienungsanleitung genann-
ten Marken und Produktnamen sind Waren-
zeichen oder eingetrageneWarenzeichen der
jeweiligen Titelhalter.
Legal notice:
Laserworld (Switzerland) AG reserves the
right to make modications to its products,
attending to further technical developments.
These modications do not necessarily have
to be recorded in each case.
This manual and its information have been
made with due care. Laserworld AG cannot,
however, take any responsibility for errata,
bugs, or the resulting damages.
The brands and product names mentioned
in this manual are trade marks or registered
trade marks of their respective owners.

Manual: Pure Micro Series
page 3 / 20
Content:
1. Scope of delivery & details
2. Preliminary warning notices
3. Initial operations, safety instructions
4. Working on the device
5. Service notes
6. Warnings and other notices on the device
7. Device connections
8. Operation
Final statement
Technical data sheet
Laser specications

Manual: Pure Micro Series
page 4 / 20
1. Scope of delivery & details
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector
1 x external PSU
1 x manual
1x Allen key 4mm
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see in-
formation on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualied persons ac-
cording to safety regulations of the res-
pective country.
4. Always ensure that maximum permissib-
le exposure (MPE) is not exceeded in are-
as accessible to the public.
5. In some countries an additional ins-
pection by technical control institutes
could be necessary.
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
7. The power supply should be easily acces-
sible.
8. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
9. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of pro-
fessional associations and/or comparable
regulations for accident prevention.
10. If the device has been exposed to great
temperature changes, do not switch it
on immediately.
11. Never use dimmer, RC or other electroni-
cally switched sockets. Whenever possib-
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of blindness!
4. Do not operate the device at high humidity or in the rain.
5. Protect device against dripping or splashing water. Do not place any liquid lled
containers at the device.
Warranty claim expires with removal of warranty label.

Manual: Pure Micro Series
page 5 / 20
le, do not use the laser projector together
with large appliances (especially fog ma-
chines) on the same mains!
12. Ensure sucient ventilation and do not
place the device on any warm or heat ra-
diating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degra-
dation of performance.
4. Working on the device
1. Be sure that the mains plug is not connected to the power sup-
ply while installing the device.
2. Take o all reecting things like rings, watches etc. before
starting to work with or at the projector.
3. Only use non-reecting tools to work on device.
4. Wear protective clothing (like goggles, gloves etc.) accor-
ding to laser power and wavelength of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/o switching of device can re-
duce durability of the laser diode drama-
tically.
• Avoid concussions during transport.
• To increase durability of your laser,
protect device against overheating:
-Always ensure sucient ventilation.
-Do not face spotlights (especially mo-
ving heads) to the device.
-Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with dierent temperature.
-Keep the device dry. Protect it from
moisture, rain and damp.
-Switch o device when it is not nee-
ded. Diodes are switched on and can
wear o even if there is no visible la-
ser output.
• Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.

Manual: Pure Micro Series
page 6 / 20
•
6. Warnings and other notices on the device
Laser radiation!
Avoid exposure
to beam.
Laser class 4
Caution of
radiation if cover
is removed power supply
& consumption
model type
wavelength
output power
production
year
Please read manual before operation
7. Device connections
connection for
power external
PSU
ILDA out
LEDs for power, over-
heat and interlock
ILDA in
trim pots for co-
lor adjustments
trim pots for
x / y shift

Manual: Pure Micro Series
page 7 / 20
8. Operation
1. Please notice:
Always connect the device to the power supply rst before connecting it to the
grid.
Make sure that your device is provided with the correct voltage. Wrong voltage could
lead to irreparable damages. Please nd the correct voltage data in the synoptical table
at the end of this manual. It must be ensured that the device is not directed to people or
inammable objects during installation.
The“Power“ diode on the rear side of the device begins to light up after the device has
been connected to power.
ILDA in / ILDA out
The device can be controlled via ILDA control signal. There are a ILDA-in (ILDA input) and a
ILDA-out (ILDA output) interfaces on the rear side of the device. Connect the laser system
to the control interface (DAC) by using an ILDA cable. Do not connect the laser to standard
parallel port at your computer, but always use an appropriate ILDA interface (usually is sold
together with the laser control software). After that you are able to control your laser by a
showlaser software (e.g. Phoenix or Pangolin). Use the ILDA-out interface to daisy-chain the
signals (from ILDA-in) to a further device.
2. X/Y Axis
There are two trim pots for X and Y axis adjustments on the rear side of the unit. Use the
X-Axis pot to vary or to glean the picture along the x-axis. Use the Y-Axis pot to vary or to
glean the picture along the Y-axis. Avoid that both pots are set to centerposition at the
same time. Otherwise the power density of the beam gets extremly high! (You can avoid
this by activating the safety with beam block.)
3. Colors
The trim pots Red, Green and Blue on the rear side of the device can be used to adjust the
single colors in their color balance.
Red: Turn the„Red“- pot to adjust the red color balance.
Green: Turn the„Green“- pot to adjust the red color balance.
Blue: Turn the„Blue“- pot to adjust the red color balance.
4. Overheat
Find the “Overheat“-LED below the “Power“-LED on the rear side of the device. By de-
fault the unit has an integrated protection against overheating. To avoid overheating,
the overheat control reduces the output power without switching the device o. If the
temperature of the device (not air temperature) becomes to high, the overheat LED lights
up and the output power of the device gets reduced. Please improve ventilation if the
Overheat LED lights up.

Manual: Pure Micro Series
page 8 / 20
5. Interlock / Safety
There is a Interlock-/Safety-LED on the rear side of the device. If this LED lights up,
one of the following cases stopped the beam output:
1. For a short time after switching on the device (self test). During the initial startup
time of a few seconds there is no output for safety reasons.
2. The device is connected to the power supply but not to an ILDA connection.
3. The interlock system of the device will block output if there is no connection to
pin 7 and 14 of the ILDA signal line.
4. The scan fail safety will block output if there is a failure at the scanning system.
5. If the beam block safety is activated, the system does not allow to project single
beams or very small patterns. This is also indicated by the safety LED.
6. Safety Presets
By default there are following safety presets in the device:
- Scan fail safety (accord. IEC 60825-3): active
- beam block safety inactive
- ILDA-Interlock processing (pins 7 + 14) active
The safety options can be adjusted at the scanner board. Please see the manuals on
Laserworld website for details.
7. Turn o
To turn o the device disconnect the power cable from the mains.
Important Note:
Operate scanners/galvos only at appropriate speed according to the res-
pecting scan angle. Too high scan speed can damage the scanning system.

Manual: Pure Micro Series
page 9 / 20
Final statement
Product and package leaving warehouse without faults. Users have to follow the local safety
regulations and warnings of this manual. Damages through inappropriate use do not unterlie
the sphere of inuence of manufacturer or dealer. Therefore no liability or warranty will be
taken over. We cannot inform you in case of changes of this manual. If you have any questions,
please contact your dealer.
For service please contact your dealer or Laserworld. Please use only spare parts of Laserworld.
Subject to change without notice. Because of the vast amount of data we cannot guarantee
any correctness of given information.
Laserworld (Switzerland) AG
Kreuzlingerstrasse 5
8574 Lengwil-Oberhofen
SWITZERLAND
Registered oce:
8574 Lengwil-Oberhofen / Switzerland
Company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
CEO: Martin Werner
VAT no. (Switzerland): 683 180
UID (Switzerland): CHE-113.954.889
VAT no. (Germany): DE 258030001
WEEE-Reg.-No. (Germany): DE 90759352
www.laserworld.com
[email protected]
representative according to EMVG:
Cleantech Europe GmbH
Managing Director: Thomas Schulze
Fürkhofstr. 5
81927 München / GERMANY

Manual: Pure Micro Series
page 10 / 20
Inhaltverzeichnis:
1. Lieferumfang & Hinweise
2. Einleitende Warnhinweise
3. Schritte zur Inbetriebnahme, Sicherheitshinweise
4. Sicherheitshinweise für Arbeiten am Gerät
5. Pege- und Wartungshinweise
6. Warnhinweise und Spezikationen am Gerät
7. Geräteanschlüsse & Bedienelemente
8. Bedienung
Abschließende Erklärung
Technische Daten
Laserleistungsdaten