2
3. If programmed as an input, you can
connect a dev ice - such as a door
contact - to th e ‘Z /P ’ terminal of th e
L C D 5 5 1 1 . T h is eliminates th e need to
run w ires b ack to th e control panel for
th e dev ice. T o connect th e z one, run
one w ire from th e dev ice to th e ‘Z /P ’
terminal and th e oth er w ire from th e
dev ice to th e B (b lack ) terminal. F or
pow ered dev ices, run th e red w ire to
th e R (positiv e) terminal and th e b lack
w ire to th e B (negativ e) terminal. W h en
using end of line superv ision, connect
th e z one according to one of th e con-
figurations outlined in your system’s
Installation M anual.
4 . If th e ‘Z /P ’ terminal is programmed as
an output, th e output follow s th e P G M
programmed in S ection [0 0 0 ][8 ]. A
small relay, b uz z er or oth er D C operat-
ed dev ice may b e connected b etw een
th e positiv e supply v oltage and th e ‘Z /
P ’ terminal (max imum load is 5 0 mA ).
Applying Power
O nce all w iring is complete, apply pow er
to th e control panel:
1 . C onnect th e b attery leads to th e b attery.
2 . C onnect th e A C transformer.
F or more information on control panel
pow er specifications, see th e control
panel Installation M anual.
NOTE:Do notconnectthe power until all wir-
ing iscomplete.
Enrolling the Keypad
O nce all w iring is complete, you w ill need
to enter a 2 -digit numb er th at tells th e
system th e partition and slot assignment
of th e k eypad.
If your system h as partitions, you w ill
need to also assign th e k eypad to a par-
tition (1 st digit).
T h e slot assignment (2 nd digit) tells th e
panel w h ich k eypad slots are occupied.
T h e panel can th en generate a fault w h en
a k eypad superv isory signal is not
present. T h ere are eigh t av ailab le slots
for k eypads. L C D 5 5 1 1 k eypads are al-
w ays assigned to slot 1 b y default. Y ou
w ill need to assign each k eypad to its
ow n slot (1 to 8 ).
E nter th e follow ing at each k eypad in-
stalled on th e system:
E nter Installer P rogramming b y press-
ing [][8 ][Installer’s C ode]
P ress [0 0 0 ] for K eypad P rogramming
P ress [0 ] for P artition and S lot A ssign-
ment
E nter a tw o digit numb er to specify th e
partition and slot assignment.
NOTE:Ifyour system doesnothave partitions,
enter [1]for the firstdigit.
1 st digit E nter 0 for G lob al K eypad
E nter 1 for P artition 1 K eypad
E nter 2 for P artition 2 K eypad
E nter 3 for P artition 3 K eypad
E nter 4 for P artition 4 K eypad
E nter 5 for P artition 5 K eypad
E nter 6 for P artition 6 K eypad
E nter 7 for P artition 7 K eypad
E nter 8 for P artition 8 K eypad
2 nd digit E nter 1 to 8 for S lot A ssignment
5 . P ress th e [# ] k ey tw ice to ex it pro-
gramming.
6 . A fter assigning all k eypads, perform a
superv isory reset b y entering
[][8 ][Installer’s C ode][9 0 2 ]. T h e pan-
el w ill now superv ise all assigned k ey-
pads and enrolled modules on th e
system.
Programming the Keypad
T h ere are sev eral programming options
av ailab le for th e L C D 5 5 1 1 k eypad. T h ese
are describ ed b elow . R ecord all your
programming ch oices in th e program-
ming w ork sh eets included in th is manual.
P rogramming th e L C D 5 5 1 1 is similar to
programming th e rest of th e system.
W h en you are in th e L C D 5 5 1 1 program-
ming sections, th e k eypad w ill display
w h ich options are turned on along th e top
of th e display. T o turn an option on or off,
press th e numb er corresponding to th e
option on th e numb er pad. T h e numb ers
of th e options th at are currently turned
O N w ill b e displayed.
