LDARC TINY TX Seres User manual

TINY TX SERIES X6
8-CHANNEL 2.4GHZ DIGITAL RADIO
USER MANUAL
Thanks for purchasing TINY TX serirs 2.4GHz digital system, RF solution of
this product use AMICCOM A7106 and SKYWORKS RFX2401C. Tiny X6 is a
8-channel easy to use radio for multirotor, it will help you simplifies the setup ,
make you focus on fly.
The current of radio about 90mA, support 2 type batterys :
<1>. Three AAA battery, 1.5V alkaline or 1.2V Ni-MH battery.
<2>. One 4.2V lithium ion battery.
WE DON'T ADVISE USE 1.5V CARBON-ZINC BATTERY !
<WHAT IN THE PACKET>
●X6 Radio x1
●AAAx3 battery box (NOT include battery) x1
●Micro S.BUS receiver x1
<BIND RECEIVER WITH RADIO>
1. Press the button of receiver then power on, green indicator on receiver
will blink fast meaning bind mode enable.
2. Press the red button of radio shown as below then power on the radio,
yellow indicator on radio shown as below will blink + buzzer meaning radio
bind mode enable.
3. Bind success when the indicator of receiver from green fast blink switch
to red on. Turn off the radio then power on, indicator of receiver will green
on, mean receiver working normal.
4. The indicator of receive green solid meaing working normally, green LED
brightness meaning signal strength. Red LED solid meaning receiver
signal lost.
<SCHEMATIC>
< SCHEMATIC DESCRIPTION>
<A>：Power switch.
<B>、<C>、<D>、<E>：5、6、7、8 channel key.
<F>：Trim key (NEED KEY COMBINATION ) :
Trim lift stick : hold 5 channel key, toggle trim key.
Trim right stick : hold 8 channel key, toggle trim key.
<G>：Battery indicator：suggest change battery when middle power.
Battery indicator
Battery status
■
High power (above 60%)
■
Middle power (40%~10%)
■+ buzzer
Low power (less than 10%)
<H>：5 channel indicator.
5 channel indicator
Channel data
■
1800
×
×
■
1200
<I>、<J>、<K>：6、7、8 channel indicator.
6、7、8 channel indicator
Channel data
■
1800
■
1500
■
1200
<CHANNEL DATA >
Tiny X6 radio support total 8 channels data output, channel’s sequence,
minimum data, neutral data and maximum data show as table below:
T
A
E
R
5CH
6CH
7CH
8CH
MIN
1050
1100
1100
1100
1200
1200
1200
1200
neutral
-
1500
1500
1500
-
1500
1500
1500
MAX
1950
1900
1900
1900
1800
1800
1800
1800
<STICK RE-CALIBRATION > AND <RADIO SETTING>
The stick of radio alreay calibration before leave factory, but after long time
use maybe result bias, user can re-calibration the stick and change radio
setting as follows:
1. make sure the radio POWER OFF, keep throttle / rudder and elevator
/ aileron stick all in neutral position.
2. HOLD three red keys as shown below then power on, the radio will into

< stick re-calibration > mode.
3. <stick re-calibration > will first run neutral calibration,ifAIL、ELE、THR、
RUD channel NOT in middle position, the A、E、T、R indicator as show
below will RED blink and buzzer. User need keep two sticks in neutral
position then run <stick re-calibration > again.
4. Range calibration will run after neutral calibration success. All LED will
CCW GREEN water work as follow, please shake stick to maximum rang.
5. After range calibration success, radio will into <radio setting> menu, the
indicator meaning and setting method as follows:
MEANING
SETTINGM
ETHOD
DEFAULT
A indicator
■AIL REV OFF
5 channel key.
■
REV OFF
■AIL REV ON
E indicator
■ELE REV OFF
6 channel key.
■
REV OFF
■ELE REV ON
T indicator
■THR REV OFF
7 channel key.
■
REV OFF
■THR REV ON
R indicator
■RUD REV OFF
8 channel key.
■
REV OFF
■RUD REV ON
M indicator
■Mode 2
Trim key,
Lift and right
■
Mode 2
■Mode 1
B indicator
■AAA battery
Trim key,
Up and down
■
AAA Battery
■Lithium battery
The radio setting will save automatic after change, user can
restart radio use power switch.
Radio use AAA battery default, if user change 4.2V lithium ion
battery, MUST change battery type in <radio setting>, or else
may cause battery leave indicator error and battery damage.
<VERSION : 00702E >
WELCOM TO LDARC.COM