le-idea IDEA16 User manual

®IDEA16/IDEA36ENInstruction Manual

DISCLAIMERPrefaceImportant StatementThe battery is made of the lithium-polymer batteryFlight EnvironmentStore ProperlyThank you for purchasing the LE-IDEA series drone.Please read this manual carefully before operating it, and please keep this manual properly for future adjustment and maintenance.The drone is a high-risk good, it must be away from the crowd when flying. Artificial assembly or damage, electronic control, or improper operation which not allowed, all of them are likely to cause damage to the aircraft, personal injury, or other unpredictable accidents. Pilots must be careful and need to understand the responsibility for accidents due to their own negligence.Lithium batteries are different from the general battery, which consists of a thin layer of thin paper wrapped with its chemical endoplasm. Which reduces its weight, but makes it more vulnerable in the face of rough or inappropriate operations. The inappropriate operation of this battery will cause an explosion.(1)Away from obstacles and crowdsThe flying drone has an uncertain flight speed and state, there is a potential risk. Fly away from the crowds, high-rise buildings, high-voltage wires, etc., meanwhile, avoiding flying in windy, rainy, thunderstorms, and other bad weather to ensure the safety of pilots, the surrounding population, and the property.(2)Away from the damp environmentThe interior of the drone is made up of many sophisticated electronic components and mechanical parts,so it is necessary to prevent the aircrat from being damp or water infiltration to avoid accidents of mechanical and electronic parts.(3)Safe operation Please operate the drone according to your own status and fight sill. Fatigue, poor spirit, or improper operation will increase the risk of an accident.(4)Keep away from high-speed rotating parts When the propellers are in high-speed spinning, please keep the drone away from the pilot, the surrounding, crowd, and objects to avoid danger and damage.(5) Keep away from heatThe drone is composed of metal, fiber, plastic, electronic components, and other materials, so you should keep it away from heat sources and avoid sun exposure and high temperature to avoid the deformation of the drone.This product is not a toy, it integrates expertise in mechanics, electronics, aerodynamics, high-frequency launching, etc. This drone integrates precise equipment, which requires proper assembly and commissioning to avoid accidents. The drone holder must operate the drone in a safe way, improper handling will cause serious personal injury or property damage. It may also be lost due to incorrect operation.This product is suitable for people who have experience in operating drones and are over 14 years old.If there is a problem during use, operation or maintenance, please contact your local sales agent or retailer, or keep in touch with the person in charge of our company.Please use only original parts and accessories.Please keep the packaging and this user manual for future reference. Any questions we would like to hear from you! Please include your order number when you contact us at email (Customer service email address: [email protected], 24 Hr/7 Day).1.2.3.4.5.6.● Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airports, or bodies of water.● DO NOT fly near strong electromagnetic sources such as power lines and base stations as it may affect the onboard compass.● DO NOT use the drone in adverse weather conditions such as rain, snow, fog, and strong wind.SAFETY PRECAUTIONS1. If the device is not going to be used for an extended period of time, remove batteries to prevent potential dama: battery leakage.2. Please do not leave batteries exposed to direct sunlight.3. Do not immerse the batteries in water or allow them to get wet.4. Please keep the battery out of reach of children or pets.
-1-

Short press to take a photo
Press and hold for 3 seconds
to record
Fine-tuning key
(Press and hold)
One key take-off/landing
Headless mode
Speed regulation
Switch
Lens up
Roll
Lens down
Right joystick
Left joystick
AA 1.5V
AA 1.5V
AA 1.5V
BATTERY CHARGING METHOD:Use carefullyWhen charging the rechargeable battery, do not use it for children alone, it must be carried out under the supervision of an adult, and it must be kept away from flammable materials when charging.Please do not short circuit or squeeze the battery to avoid explosion.The power terminals should not be taken out of the model, and the terminals should not be short-circuited; do not short-circuit, disassemble, or throw the battery into fire; do not place the battery in a high-temperature, heated place (such as in a fire or near an electric heating device).The model can only use the recommended charger. Please regularly check whether the wires, plugs, shells and other parts of the charger are damaged. If any damage is found, stop using it until the repair is complete.The charger is not a toy; the charger should only be used indoors.The battery after flight needs to be charged and then stored. If it is not used for a long time, it is recommended to charge the battery at least once every 3 months to avoid over-discharge of the battery which would cause permanent damage to the battery.1. First, connect your USB cable to the drone battery, then connect it to your favorite charging source.2. The red light is on when the battery is charging, and the green light is always on when the battery is fully charged. Battery charging time is approximately120 minutes.● ● ● ● ● ● USB charging cableDrone’s batteryAdapter (sold separately)●Remove and put the battery in the correct way●Non-rechargeable batteries cannot be charged●The rechargeable battery can only be charged under the supervision of an adult●Different types of batteries or old/new batteries cannot be mixed●Only batteries of the same model or equivalent to the recommended model can be used●Batteries are inserted with correct polarity●The rechargeable battery should be removed from the drone before charging●Depleted batteries should be removed from the drone●The power terminals must not be short-circuited.PACKAGE LIST
DRONERemote ControlBattery×2Propeller×4ScrewdriverUSBUser ManualTRANSMITTER OVERVIEW
Open the battery cover and insert 3 AAA batteries as shown below (not included).
-2-

QUICK-START GUIDE● Insert the drone battery. Turn on the drone switch (Figure 1) and place it on a flat surface; the drone light will flash.● Push the throttle and joystick to the lower right corner at the same time, the buzzer will emit a "Di" sound, and the aircraft's lights will flash and then stay on, indicating that the leveling correction is completed. (Figure 3)● Push the throttle and joystick outward at the same time（Figure 4） to take off the drone.● Turn on the remote control switch (Figure 2), it will prompt a "Di", the red light of the remote control will be on, and the indicator of the aircraft will be on, then the frequency matching is completed.Figuer1Figuer
2
Figuer3Figuer4HOVER UP AND DOWNPush the THROTTLE STICK up to fly the drone up, and pull the THROTTLE STICK down to fly the drone down.FLY FORWARD OR BACKWARDPush the DIRECTION CONTROLSTICK up to fly the drone forward, and pull the DIRECTION CONTROLSTICK down to fly the drone backward.FLY LEFT OR RIGHT Move the DIRECTION CONTROLSTICK to the left to fly the droneto the left, and move the DIRECTIONCONTROL STICK to the right to fly the drone to the right. ROTATE LEFT OR RIGHTMove the THROTTLE STICK to the left to rotate the drone to the left, andmove the THROTTLE STICK to the right to rotate the drone to the right.
-3-
When taking off, the fuselage is offset to the rear, press and hold the fine-tuning button, push the right joystick forward until the aircraft is stable, and release the fine-tuning button to exit the fine-tuning function. When taking off, the fuselage is shifted forward, press and hold the fine-tuning button, push the right joystick backward until the aircraft is stable, and release the fine-tuning button to exit the fine-tuning function.When taking off, the fuselage is offset to the right. Press and hold the fine-tuning button, push the right joystick to the left until the aircraft is stable, and release the fine-tuning button to exit the fine-tuning function. When taking off, the fuselage is shifted to the left, press and hold the fine-tuning button, push the right joystick to the right until the aircraft is stable, and release the fine-tuning button to exit the fine-tuning function.

Figuer5Figuer6Figuer7Figuer8Figuer9The fast and slow gears are divided into three gears forward, backward, and left and right. After the remote control is powered on, the default is the slow gear. Press the remote controller key (as shown in Figure 7) to make two sounds of “Di” and “Di”, it is the middle gear. "Di", "Di" and "Di" press three times for fast gear, and one "Di" to return to slow gear. (It is recommended for beginners to use slow gear operation)Headless Mode allows you to fly your drone without knowing its orientation because it will be fixed in the direction you set it.During the flight, the camera can adjust the up and down direction, press the rotation button on the remote control camera, and the camera lens rotates up, and the down rotation operation is the same.Short press the button, the mobile phone APP will make a clicking sound, and the camera will take a picture and store it in the mobile phone album. Press and hold for 3 seconds to start recording, press and hold again for 3 seconds to save the recording to the phone album, and stop recording.Long Press the 360°Flip button to flip the drone. The remote control will Di twice, indicating the drone is in Flip Mode.Next, move the direction stick up or down, and the drone will flip up or down (Figuer. 5)Move the direction stick to the right or left, and the drone will flip left or right (Figuer. 6)Note：● Only execute rolls when you have plenty of airspaces. The drone can only perform flips when it is at least 7 feet in the air.● This function can not be used when the drone is in a low power state.● 360°Flip● Speed modes●Remote control to control camera recording● Headless modeDefinition of the direction before takeoff: Make the forward direction of the aircraft in front of you (Figure 8)(Note: the side with the camera is the front)After the drone is calibrated, when the one-key take-off/landing button is pressed, the drone will automatically start and rise to a certain height. When the drone is high in the air, the drone will automatically descend when the one-button take-off/landing button is pressed.Press the Headless Mode button to enter Headless Mode before take-off (Figure 9). The remote control will Di continuously and the drone lights will begin to flash to indicate mode selection. Press the remote control again to make a "Di" sound to exit the headless mode.● One key take-off/land
-4-
Notice:This camera adjustment button needs to be pressed with a interval, if it is pressed continuously, it will affect the acceptance of the aircraft signal, the aircraft may get stuck, making it impossible to adjust the camera angle.

Long press 3 seconds to turn on the power, enter (Mobile or IPAD) "Settings" option, open the wireless network, find the name of the device "WIFI-4K-*****" in the wireless network search list and connect it. After the connection is successful, exit the setting option.Open the “Fly Plus” software icon on your mobile phone and enter the control interface. (Try to stay away from other signal sources when flying)
WIFI-4K-2AE371

● Rocker
Notice: After connecting to the aircraft, turn on the control in the control mode
Throttle slide up/downThe aircraft will ascend/descendSteering: Swipe left/rightThe aircraft will rotate left/rightFront/Back: Swipe up/downThe aircraft will go forward/backwardSide flight: swipe left/rightThe aircraft will fly left/right
1、Download and installation instructions of APP software1.1 Download and install the software1.2 Description of links2、 Function introductions of APP control interface
● Control mode
-5-

● Flight modes2. 360° Flip360° Flip: After clicking the 360° flip mode, slide the right joystick to the maximum in any direction, and the flight will roll in the corresponding direction.3. Track ModeTrajectory Mode: Draw a line on the screen, and the aircraft will fly according to the drawn trajectory.Notice:● This feature can only be done if you have enough airspace.● This function cannot be used when the drone is in a low battery state.1.Gravity SensingNotice:● This feature can only be done if you have enough airspace.● This function cannot be used when the drone is in a low battery state.
-6-
Notice:● Only execute rolls when you have plenty of airspaces. The drone can only perform flips when it is atleast 7 feet in the air.● This function can not be used when the drone is in a low power state.Gravity Sensing Mode: When the aircraft is successfully connected to the mobile APP, turn on the gravity sensing mode and tilt the phone to control the aircraft to fly forward, backward, left, and right.

ProblemReasonsSolutionThe flight not respondingThe flight response of the aircraft is not sensitiveFly sideways when hoveringThe direction of forward-ing flight is detected in the headless stateUnstablefixeheight/shaking up and down1. The drone enters low voltage protection 2. When the power of the remote control is low, the power indicator will flash1. The remote control is in low power2.Remote control with the same frequency is emitting interferenceDid not proceed the calibration successfullyHead deviation caused by multiple collisions1. Did not proceed the calibra-tionsuccessfully 2. Unstable air pressure in bad weather conditions3. Severe collision causes gyroscope data disorder1. Charge the aircraft battery2. Replacing the Remote Control Batteries1. Replacing the Remote Control Batteries 2.Change to a place that does not transmit interference on the same frequencyProceed the calibration again(Preparation for Flight)Redefine the front direc-tion(Headless mode)1. Proceed the calibration again (Preparation for Flight)2. Try to avoid flying in bad weather3. Proceed the calibration again(Preparation for Flight)
After-sales information:le-idea®|©2022 ALL RIGHTS RESERVED
®
Official:http://www.le-idearc.com/contact-us_d3Youtube:https://youtube.com/channel/UCQW-JKq5uh-F7Rnz9fjIhCgEmail: [email protected] (24hr/7d)
-7-
This content is subject to change lf you have any questions about this document, please contact le-idea by sending a message to us.

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
for Remote control:
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
for Drone:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
& your body.