Lectrosonics Dante M2T/E01 User manual

M2T/E01and M2T/E01/ND
Digital IEM Transmitter
INSTRUCTION MANUAL
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
M2T/E01 Dante
M2T/E01 Non Dante
This manual is for all 1.X
versions of Duet Firmware.

M2T/E01
LECTROSONICS, INC.
2

Digital IEM Transmitter
Rio Rancho, NM 3
Table of Contents
Introduction.............................................................................................................................................................................................4
What is Dante? .....................................................................................................................................................................................4
System Setup Procedures.....................................................................................................................................................................5
Summary of Steps ................................................................................................................................................................................5
Panels and Features...............................................................................................................................................................................6
M2T/E01 Front Panel ............................................................................................................................................................................6
M2T/E01 Back Panel ............................................................................................................................................................................6
Operating Instructions ..........................................................................................................................................................................7
IR (infrared) Port ...................................................................................................................................................................................7
USB Port ...............................................................................................................................................................................................7
Headphone Volume Adjustment............................................................................................................................................................7
Dante Ports (optional) ...........................................................................................................................................................................7
Ethernet Port.........................................................................................................................................................................................7
Power Inlet ............................................................................................................................................................................................7
Quick Sync............................................................................................................................................................................................7
Navigating the Menus ...........................................................................................................................................................................7
LCD Menu Map........................................................................................................................................................................................8
Menu Item Descriptions.........................................................................................................................................................................9
RF Enable/Level....................................................................................................................................................................................9
RF Tuning..............................................................................................................................................................................................9
Sync Scan.............................................................................................................................................................................................9
Sync Settings........................................................................................................................................................................................9
Sync FlexList™ .....................................................................................................................................................................................9
Audio Level/Trim..................................................................................................................................................................................10
Audio Input Type .................................................................................................................................................................................10
Audio Polarity ......................................................................................................................................................................................10
Headphone Monitor ............................................................................................................................................................................10
Front Panel Setup ...............................................................................................................................................................................10
Network Settings.................................................................................................................................................................................10
Edit Names .........................................................................................................................................................................................10
Restore Defaults .................................................................................................................................................................................11
About...................................................................................................................................................................................................11
Links....................................................................................................................................................................................................11
Hardware Installation ...........................................................................................................................................................................12
Unpacking the Unit..............................................................................................................................................................................12
Items Included in the Box:...................................................................................................................................................................12
IInstalling two M2T/E01s into a Single Rack Space............................................................................................................................13
Wireless Designer Software and USB Driver.....................................................................................................................................15
Wireless Designer Software and USB Driver.....................................................................................................................................16
Software Installer ................................................................................................................................................................................16
Firmware Update Instructions.............................................................................................................................................................16
Accessories ..........................................................................................................................................................................................17
Specifications and Features................................................................................................................................................................18
Service and Repair ...............................................................................................................................................................................19
Returning Units for Repair ..................................................................................................................................................................19

M2T/E01
LECTROSONICS, INC.
4
Introduction
The M2T/E01 Digital Half-Rack Transmitter with analog
and digital Dante™ optional network audio inputs
presents an excellent sounding IEM system with a unique
level of performance in a wireless in-ear monitor system.
With ultra-low latency, 24-bit audio, digital RF modulation
and two stereo digital channels, the M2T/E01 provides
a truly unique IEM product for demanding, professional
applications.
The M2T/E01 boasts a USB port for firmware updates
and an IR port for fast setup. A large, high resolution,
backlit LCD and large membrane switches provide an
intuitive interface that is highly visible in daylight or dimly
lit conditions.
The half-rack transmitter provides four audio inputs which
can be individually configured to be analog or Dante
compatible. The input connectors are full size XLR/TRS
combo types for balanced line level analog signals. Input
preamp circuits use a special balanced amplifier with very
high common mode rejection to minimize hum and noise.
Analog signals are converted to an internal 24-bit digital
format which is then encoded, organized into packets,
and passed to an RF modulator. The modulated RF signal
is filtered before and after amplification to suppress out-
of-band noise and spurious signals.
Conventional in-ear wireless monitor systems rely
on decades-old technology: FM transmission with
multiplexed, companded audio. The M2T/E01 Transmitter
employs unique technology to provide ruler-flat frequency
response from 20 Hz to 15 kHz and maximum channel
separation. In addition, the digital audio eliminates a
compandor and the associated artifacts. The result is
crystal clear sound and extremely low distortion
of <0.15%.
The M2T/E01 is designed and developed with the
professional touring, installation, theater and broadcast
customers in mind. The transmitter chassis is all-metal.
The front panel is an aluminum extrusion with a durable
powder coat finish.
What is Dante?
Audinate’s patent pending Dante™ technology is a
flexible Internet Protocol (IP) and Ethernet based digital
AV network technology that eliminates the many bulky
cables needed to provide point-to-point wiring for ana-
log AV installations.
With Dante, existing infrastructure can be used for high
performance audio as well as for ordinary control, moni-
toring or business data traffic. Digital networks utilize
standard IP over Ethernet offering high bandwidth ca-
pable of transporting hundreds of high quality channels
over Gigabit Ethernet.
Set-up and configuring the system is made easy as
well, saving enormous installation costs and long term
cost of ownership on a digital network. The physical
connecting point is irrelevant: audio signals can be
made available anywhere and everywhere. Patching
and routing now become logical functions configured in
software, not via physical wired links
Summary of Dante Benefits
• Plug-and-play technology – automatic discovery
and simple signal routing
• Reduced Cost & Complexity- No special skills
required to set up audio networking
• Sample accurate playback synchronization
• Add/remove/rearrange components at will
• Deterministic latency throughout the network
• Support mixed bit depths and mixed sample
rates over one network
• Scalable, flexible network topology supporting a
large number of senders and receivers
• Supports 1Gbps networks
• Supports a single integrated network for audio,
video, control, monitoring
• Uses inexpensive, off-the-shelf computer
networking equipment

Digital IEM Transmitter
Rio Rancho, NM 5
System Setup Procedures
Summary of Steps
1) Connect power using supplied DCR15/4AU power
supply.
2) Power receiver and scan RF spectrum on site.
3) Sync Scan to transfer information from receiver
to transmitter.
4) Tune transmitter to unoccupied channels in scan.
5) Sync receiver (refer to receiver manual).
6) Turn on transmitter RF.
7) Send audio sources to transmitter.
WARNING: Increasing the Pregain can make
headphone volume excessively loud. Use
caution when setting and using.

M2T/E01
LECTROSONICS, INC.
6
USB Port
Antenna
Jack
Power Inlet
Menu navigation
buttons Power switch
Return to
previous screen
Panels and Features
IR Port
Headphone Volume
Adjustment
Dante Ports (optional)
Ethernet Port
Antenna
Jack
Headphone Jack
Reset Button
M2T/E01 Front Panel
M2T/E01 Back Panel
Menu/Select
Channel Function
Buttons/
Auick Sync
XLR/TRS Combo Analog
Input Connectors

Digital IEM Transmitter
Rio Rancho, NM 7
Operating Instructions
IR (infrared) Port
Settings, including frequency, name, limiter, mix mode,
etc. can be transferred to and from the M2T/E01 trans-
mitter via this port to an IR enabled receiver to simplify
setup.
USB Port
For firmware updates and connection to Wireless De-
signer Software.
Reset Button
For MCU recovery in the event of an interrupted firm-
ware update.
Headphone Volume Adjustment
Adjust the headphone volume, and select source with
A1, A2, B1, B2 buttons.
Antenna Output Jacks
Two standard 50 ohm BNC connectors can be used
with whip antennas or coaxial cable connected to re-
mote antennas.
Dante Ports (optional)
A Dante Digital Audio Network Interface.
Ethernet Port
Used for setup, monitoring and control with Wireless
Designer Software.
Power Inlet
The threaded-locking DC coaxial jack accepts 9-18
VDC and draws 1.2A maximum.
Quick Sync
Sync an M2R rapidly by utilizing the Channel Function
Buttons. A long (1 second) press of one of the buttons
(A1, A2, B1, or B2) on the front panel initiates Quick
Sync. Two options are available, “SYNC ALL” or “SPLIT
MONO”. The mode is selected prior to sync in the Front
Panel Setup menu item.
NOTE: See Front Panel Setup for more instruction
on the Quick Sync function.
Power Screens
When powering on the M2T/E01, there are three
screens that appear in the following order, Duet, Lectro-
sonics, RF On/Off.:
WARNING: If RF ON is selected and the
user chooses to “Do Not Show Again” RF
transmissions will be on when M2T/E01 is
powered on and may interfere with frequencies
already in use. This can be reset in the FRONT
PANEL menu.
Navigating the Menus
All Menu setup items are arranged in a vertical list on
the LCD. Press MENU/SEL to enter the menu, then
navigate with the UP and DOWN arrows to highlight
the desired setup item. Refer to the menu map on the
following page.
NOTE: To guarantee chosen parameters are
saved, exit a setup screen BEFORE powering
down M2T.
Press MENU/
SEL to enter
the menu
Press the UP and DOWN arrows
to navigate and highlight the
desired menu item
Press MENU/SEL
to enter the setup
of the highlighted
item
Press BACK to return to
the previous screen
Press the UP and DOWN arrows
to navigate and highlight the
desired item

M2T/E01
LECTROSONICS, INC.
8
LCD Menu Map
RF ENABLE/LEVEL
RF TUNING
SYNC SCAN
SEL
BACK
SEL
BACK
SEL
BACK
SYNC SETTINGS SEL
BACK
SYNC FLEXLIST SEL
BACK
AUDIO LEVEL/TRIM SEL
BACK
SEL
BACK
AUDIO INPUT TYPE
SEL
BACK
SEL
BACK
SEL
BACK
SEL
BACK
HEADPHONE
MONITOR
FRONT PANEL
SETUP
NETWORK
SETTINGS
EDIT NAMES
AUDIO POLARITY SEL
BACK
EDIT NAMES
NETWORK
SETTINGS
FRONT PANEL
SETUP
RF ENABLE/LEVEL
RF TUNING
SYNC SCAN
SYNC FLEXLIST
AUDIO LEVEL/TRIM
AUDIO INPUT TYPE
AUDIO POLARITY
HEADPHONE
CONFIG
Use arrow keys
to enable or
adjust
Press SEL to
select desired
adjustment step
Use arrow keys
to select desired
frequency
Press SEL to
select desired
adjustment step
Use arrow keys
to select desired
sync command
or tune frequency
Press SEL to
select desired
function
SYNC SETTINGS Use arrow keys
to select desired
sync command
Press SEL to
select desired
function
Use arrow keys
to adjust setting
Press SEL to
select desired
function
Use arrow keys
to select desired
audio setting
Press SEL to
select desired
channel
Use arrow keys
to select desired
channel
Press SEL to
engage function
Use arrow keys
to select desired
audio setting
Press SEL to
select desired
channel
Use arrow keys
to select desired
headphone
output setting
Use arrow keys
to adjust desired
front panel
setting
Press SEL to
select desired
function
Use arrow keys
to adjust desired
settings
Press SEL to
select desired
adjustment step
Use arrow keys
to enter desired
name
Press SEL to
select desired
function
SEL
BACK
RESTORE
DEFAULTS
RESTORE
DEFAULTS
Use arrow keys
to select yes
or no
Press SEL to
execute
No selections available; for
information purposes only
SEL
BACK
ABOUT
SEL
BACK
LINKS LINKS
ABOUT
No selections available; use phone to scan QR code
for more information

Digital IEM Transmitter
Rio Rancho, NM 9
Menu Item Descriptions
RF Enable/Level
Allows RF transmission to be turned on and off and set
RF levels at 10, 25 or 50 mW.
RF Tuning
Allows manual selection of the operating frequency.
Sync Scan
Receive frequency scan via IR port or tune transmitters
manually.
Screen will alert user if scan is unsuccessful.
Sync Settings
Allows sending or retrieving setup data via IR port.
Sync FlexList™
FlexList allows the user to set up a list of profiles, by
name, in the receiver. This allows quick and easily ac-
cess to listen to any of the mixes on site.
After putting the receiver into Sync Flex mode, choose
the function (add, update) and then use the transmitter
to send the profile over IR.

M2T/E01
LECTROSONICS, INC.
10
Audio Level/Trim
Set audio inputs at correct levels.
Easily switch between
channels with A1, A2, B1
or B2 Buttons.
Audio Input Type
Set independent channels to analog or digital (Dante)
if available.
NOTE: When selecting a Dante input, user must be
familiar with the Dante Controller from Audinate.
Audio Polarity
Select normal or inverted polarity for each
audio channel.
Headphone Monitor
The headphone source can be selected here or on the
front panel, using the A1, A2, B1 or B2 Buttons.
Front Panel Setup
Front panel settings may be customized as follows:
• LCD brightness
• Front panel lock
• Startup RF state
• Quick Sync Mode
Sync All: A long (1 second) press of
either the A1, A2, B1 or B2 buttons sends all
RX1 settings.
Split Mono: A long press of the A1or B1
buttons sends all RX1 settings with the mix mode
forced to Mono Ch. 1. A long press of the A2 or
B2 buttons sends all RX1 settings with the mix
mode forced to Mono Ch. 2.
Network Settings
Allows the user to set IP address or other network set-
tings when needed.
NOTE: New network settings require the unit
to reboot to take effect. Making a change and
pressing the BACK key will prompt the user to
Reboot Now, Save and Exit, or Discard and Exit.
Edit Names
Edit names to match talent for easy location in the
FlexList or easily identify multiple M2T/E01 transmitters
in a rack.
• Use UP and DOWN Arrows to select letters and
MENU/SEL to set and move cursor.

Digital IEM Transmitter
Rio Rancho, NM 11
Restore Defaults
Returns all settings to the factory defaults.
About
Displays general information about the M2T/E01,
including serial number, and the hardware, FPGA and
microcontroller firmware versions.
Links
QR codes with links to the Lectrosonics website, the
M2T/E01 User Manual online and YouTube video tutori-
als.

M2T/E01
LECTROSONICS, INC.
12
(2) A500RA20
Antenna
Hardware Installation
Unpacking the Unit
Compare the packing list enclosed with the M2T/E01
with the original order. Inspect all items for damage. Im-
mediately call 1-800-821-1121 to report any items that
are missing or damaged. The sooner we get notified,
the sooner we can get any needed replacement items
shipped to your location.
Items Included in the Box:
• Instruction manual
• (DCR15/4AU) Power supply cable
• (21926) USB cable
• (35800) Hex L key wrench
• (25990) Bracket rear tie
• (25991) Bracket front tie
• (27076) Rack flange bracket
• (27082) Rack handle
• (28885) (4) SCR10 cap screw
• (35664) (4) Rubber foot large
• (35959) Hole plug
• (A500RA20) (2) Antenna
35800 Hex L
key wrench 25991 Bracket
front tie
27076 Rack
flange bracket
27082 Rack handle
(4) 35664 Rubber
foot large
35959 Hole Plug
25990 Bracket
rear tie
(4) 28885 SCR10
cap screw
21926
Cable USB
DCR15/4AU DC
power supply

Digital IEM Transmitter
Rio Rancho, NM 13
IInstalling two M2Ts into a Single Rack
Space
The M2T transmitter occupies a half rack space, and
comes with hardware to mount two transmitters into a
single rack space.
1. Remove the Trim Cap (Part #P1330) from both
sides of the front panel on both transmitters.
2. Remove the breakaway tabs on both sides of the
chassis side panels. Use a flat blade screwdriver
to pry the tabs outward and snap them off of the
chassis.
3. Insert the flange bracket (Part #27076) into the
open slot in the side of the chassis cover panel.
4. Insert two (2) cap screws (Part #28885) through the
rack handle (Part #27082) holes and install the rack
handle onto the flange bracket through the holes in
the unit’s front panel. Firmly tighten the cap screws
using the hex key (Allen wrench) as shown.
5. If antennas will NOT be mounted on the front
panel of the transmitters, install the hole cap (Part
#35959) by aligning the flat on the cap with the flat
on the opening.
NOTE: The retaining nuts on the panel and tie
brackets are “tensioning lock nut” types designed
to prevent the screws from coming loose due to
vibration.You will usually feel resistance as you
tighten the screws - this is normal.
continued on next page...

M2T/E01
LECTROSONICS, INC.
14
Tensioning lock
nuts on the rear
side of the bracket
6. Install one side of the front tie bracket (Part #25991)
into the side panel opening in one of the receivers.
Insert the screws, but do not tighten them com-
pletely at this point.
Slide the other receiver over the tie bracket and in-
sert the screws, but do not tighten them completely
until the rear tie bracket is installed.
Rear tie bracket
(Part #25990)
Front tie bracket
(Part #25991)
7. Remove the four cap screws from the adjacent rear
panels, and them use them to attach the rear tie
bracket. Do not tighten the screws completely.
8. After front and rear tie brackets are installed, place
the receivers on a flat surface so the that the front
panels are even with each other. Hold the receivers
in place and tighten all cap screws on the front and
rear brackets.
NOTE: If the supplied rubber feet are installed on
under side of M2T, it will not fit in a rack unless
there is an empty space below it.

Digital IEM Transmitter
Rio Rancho, NM 15
Wireless Designer
Software and USB Driver
Windows Installation
Download the Wireless Designer software installer
from the web sites under the SUPPORT tab at:
http://www.lectrosonics.com/US
http://www.lectrosonics.com/europe/
or use the flash drive supplied with the receiver.
These instructions are useful for the first time the soft-
ware is being installed. Once the software is installed,
updates are available by simply clicking on an item in
the Help Menu. Refer to the help menu for details.
Launch the installer and follow the screen prompts.
I Agree on the EULA (end user license agreement)
must be checked to continue the installation.
The installer includes USB drivers, which only need to
be installed once. By default, the boxes are unchecked
in the installer, because they are not required except
for the very first time the software is installed on the
computer being used.
If it is the first time the software is being installed,
check the appropriate box to install the USB driver for
the receiver model you are connecting.
If the USB driver is installed, the software will commu-
nicate with whichever model is connected.
When the installation is complete, the confirmation
screen will appear. Click on Finish to complete the
installation.

M2T/E01
LECTROSONICS, INC.
16
Wireless Designer
Software and USB Driver
Software for Mac®OS X Operating Systems
Installation
Using only the Firefox web browser, open Wireless De-
signer. If the Firefox Silverlight plugin has not been used
before you will be prompted to “Activate Silverlight”
before Wireless Designer loads.
Note: The Apple Safari web browser no longer
suppors installation of Silverlight applications
like Wireless Designer. Existing installations will
continue to work normally, but new installations
must be made using the Mozilla Firefox Browser.
After Wireless Designer loads, right-click on the page
and choose “Install Wireless Designer onto this com-
puter...” from the pop-up menu. A dialog box will open to
confirm, click “Install” to proceed.
A dialog box will open to announce that Wireless De-
signer has been added to your downloads folder. Click
the “Open Downloads Folder” button and drag Wireless
Designer onto the Dock or into your Applications folder.
Double-click Wireless Designer to launch it. The first
time you launch it you may receive a “Wireless De-
signer can’t be opened...” warning. If so, click “OK” to
dismiss the warning and perform the following steps
immediately:
Open the Apple “System Preferences” application and
double-click the “Security & Privacy” icon.
Near the bottom of the “Security & Privacy” pane you
should see the message “Wireless Designer was
blocked from opening because it is not from an identi-
fied developer.”
Click “Open Anyway”. Another warning dialog box
opens, click “Open” to launch Wireless Designer. This
only needs to be done once, Wireless Designer will
launch normally thereafter.
Note: If Wireless Designer is already installed,
you must uninstall it before attempting to install a
new copy. Drag the Wireless Designer Dock icon
to the desktop to remove it.
Software Installer
Installation software supplied on USB drive. Can also
be downloaded from the web site.
WDDISK
Firmware Update
Instructions
Firmware updates are made with a file downloaded
from the web site and a USB connection to the receiver.
Refer to Help in Wireless Designer software for the
procedure.

Digital IEM Transmitter
Rio Rancho, NM 17
Accessories
DCR15/A4U
Front Mount Antenna Kit FMAKM27
27080 Dante Port Cover
(included with Non Dante Model)
Dante 4X4-TM Dante Card Kit
(Included in Dante Model)
RMPM2T-1
Rack kit for mounting one M2T/E01 into a single rack
space
SNA600a Antenna
SNA600a Accessories:
ARG 15
A 15 foot antenna cable of standard RG-58 coax
cable with BNC connectors at each end.
ARG 25; ARG 50; ARG 100
Antenna cable of Belden 9913F low-loss coax cable
with BNC connectors at each end. Number speci-
fies length in feet.

M2T/E01
LECTROSONICS, INC.
18
Specifications and Features
RF Power Output: • Two carriers; two audio channels each
• Power adjustable on each carrier to 10, 25 or 50 mW
Antenna Output: 2 x BNC sockets
Operating Frequencies: 470.100 – 614.375 MHz
Frequency Selection Steps: 25 kHz
Frequency Stability: ± 0.002%
Modulation: 8 PSK
Emission Designator: 200KG7E
Spurious Radiation: Compliant with ETSI EN 300 422-1 v2.1.2
Equivalent input Noise: –128 dBV
Latency: (overall system)
Digital Source: 1.0 ms plus Dante network (on Dante unit)
Analog Source: <1.4 ms
Audio Frequency Response: 20 HZ - 15 KHZ, -3 dB
Audio Input: -10 dBV or +4 dBu settings w/ ±5 dB trim
Audio Input Jack: 4 x combo XLR/TRS connectors
Dante Connection: 2 x RJ45. Internally routable with Ultimo 4x4 module
Ethernet Connection: RJ45
USB Connection: Micro USB on front panel for firmware updates
IRDA: IR transceiver for sync of receivers
Input impedance: Line: 2k Ohm
Headphone jack 1/8 inch stereo jack
Power Requirements: 9-18V DC
Power Consumption: 5 Watts
Weight: 2.2 lbs (997.903 grams)
Dimensions: Height: 1.750 in. / 44.45 mm
Width: 8.375 in. / 212.7 mm
Depth: 7.750 in. / 196.8 m.
Specifications subject to change without notice.

Digital IEM Transmitter
Rio Rancho, NM 19
Service and Repair
If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment
needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting
cables and then go through the Troubleshooting section in this manual.
We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-
tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection,
send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set at the
factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are
no adjustments inside that will make a malfunctioning unit start working.
LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs
are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest
flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does
to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone
for out-of-warranty repairs.
Returning Units for Repair
For timely service, please follow the steps below:
A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need
to know the nature of the problem, the model number and the serial number of the equipment. We also need a
phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time).
B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed
your repair through our receiving and repair departments. The return authorization number must be clearly shown
on the outside of the shipping container.
C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the
proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed” for
safe transport.
D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-
age to equipment that you ship. Of course, we insure the equipment when we ship it back to you.
Lectrosonics USA:
Mailing address: Shipping address: Telephone:
Lectrosonics, Inc. Lectrosonics, Inc. [phone]
PO Box 15900 561 Laser Rd. NE, Suite 102 [phone] Toll-free
Rio Rancho, NM 87174 Rio Rancho, NM 87124 [phone] Fax
USA USA
Web: E-mail:
www.lectrosonics.com [email protected]
[e-mail]
Lectrosonics Canada:
Mailing Address: Telephone: E-mail:
720 Spadina Avenue, [phone] Sales: [e-mail]
Suite 600 [phone] Toll-free Service: [email protected]
Toronto, Ontario M5S 2T9 (877-7LECTRO)
[phone] Fax

581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com
[phone] • [phone] • fax [phone] • [email protected]
m
LIMITED ONE YEAR WARRANTY
The equipment is warranted for one year from date of purchase against defects in
materials or workmanship provided it was purchased from an authorized dealer. This
warranty does not cover equipment which has been abused or damaged by careless
handling or shipping. This warranty does not apply to used or demonstrator equipment.
Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any
defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot
correct the defect in your equipment, it will be replaced at no charge with a similar new
item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.
This warranty applies only to items returned to Lectrosonics, Inc. or an authorized
dealer, shipping costs prepaid, within one year from the date of purchase.
This Limited Warranty is governed by the laws of the State of New Mexico. It states the
entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any
breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR
ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT
SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL,
OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE
THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF
LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE
EQUIPMENT.
This warranty gives you specific legal rights. You may have additional legal rights which
vary from state to state.
28 November 2018