Lectrosonics M187 User manual

M187
BELT-PACK TRANSMITTER
LECTROSONICS, INC.
Rio Rancho, NM
OPERATING INSTRUCTIONS
and trouble-shooting guide

2
TABLE OF CONTENTS
INTRODUCTION .................................................................................................. 2
GENERAL TECHNICAL DESCRIPTION ............................................................. 3
CONTROLS AND FUNCTIONS .......................................................................... 4
BATTERY REPLACEMENT ................................................................................. 6
OPERATING INSTRUCTIONS ............................................................................ 7
MICROPHONE CORD TERMINATION ............................................................... 8
M187 INPUT JACK WIRING ................................................................................ 9
TROUBLESHOOTING ....................................................................................... 11
SPECIFICATIONS AND FEATURES ................................................................. 12
SERVICE AND REPAIR ..................................................................................... 13
RETURNING UNITS FOR REPAIR ................................................................... 13
WARRANTY ......................................................................................... Back cover
INTRODUCTION
Thank you for selecting the Lectrosonics M187 transmitter. This transmitter repre-
sents over 70 years of combined experience in the design of RF devices and sets
new standards for operational convenience, flexibility and mechanical ruggedness.
The M187 transmitter features all metal construction and operates on high band
frequencies from 150MHz to 216MHz. The M187 was designed primarily for “belt-
worn” applications, however it works equally well for other applications and with
virtually any mounting configuration.
The M187 uses the microphone cord as the antenna, eliminating an unsightly
“dangling wire”. This transmitter may be used with a wide variety of audio sources.
The multi-pin input jack allows the use of “phantom powered” lavalier microphones
with either positive or negative bias voltages. The M187 will also match low imped-
ance dynamic microphones and high impedance inputs such as musical instruments
or tape decks.
Only the M187 transmitter is covered in this manual. Receivers are described in
separate manuals. The M187 operates with any Lectrosonics 187 Series VHF
receiver. A matched transmitter/receiver combination makes up a wireless “system”.
The M187 transmitter is FCC type accepted under the following Parts:
Part 90 (169-172 MHz) Part 74 (174-216 MHz)

3
Belt-Pack Transmitter
Rio Rancho, NM – USA
M187 Block Diagram
GENERAL TECHNICAL DESCRIPTION
The M187 transmitter is comprised of four major functional subsystems: the input compressor, the mic preamp/gain
control, the compandor, and the RF transmitter (see block diagram below).
The mic preamp is an ultra-low noise type op-amp. Aside from gain control, this stage also adds high frequency pre-
emphasis to the audio signal. This insures highest signal-to-noise ratios under varying signal conditions. Gain control
is semi-logarithmic to provide smooth gain control action.
The compandor is a high quality audio device that processes the input signal such that large dynamic ranges of input
signal can be transmitted to the receiver without overload or noise. A complementary system in the receiver recovers
the original dynamics of the signal for full audio quality. Compression and expansion ratios are complementary at 2:1.
High frequency pre-emphasis is implemented in the transmitter to provide another 10dB signal-to-noise ratio improve-
ment. Matching de-emphasis is provided in all receivers.
The compressor/limiter is a low distortion shunt FET compressor. Control signals for the compressor are derived
after the compandor to eliminate any possibility of overload under any signal condition up to a maximum of 3 Volts
input. The range of limiting action before gross distortion occurs is 35dB.
The compandor in the 187 series transmitters is much tighter than the 185 series. The H187 compandor will hold the
transmitter deviation to no more than ±15kHz under all circumstances. The 185 compandor would allow some
excursions beyond 15kHz during strong audio “spikes.”
The RF transmitter is composed of a crystal stabilized main oscillator followed by a frequency tripler and two fre-
quency doublers. All three stages are double tuned. Double tuning provides high attenuation of spurious signals,
which in turn minimizes the possibility that a transmitter would interfere with another transmitter/receiver system on
another frequency.
All RF stages are biased from a regulated internal power supply. The output stage has a separate feedback regulator
which not only stabilizes its operating point, but also minimizes AM distortion. These regulators keep the RF and
audio performance consistent from the beginning (9 Volts) to the end (6.5 Volts) of battery life.
Schematics and alignment instructions will be provided to qualified repair personnel upon request.
MIC PREAMP
LIMIT
LED
LEVEL
LED
COMPANDOR (VCO)
+9V IN
45MHZ 90MHZ 180MHZ
1
2
3
4
5
15 MHZ XTAL
OSCILLATOR
BATTERY
SENSOR
CIRCUIT
POWER
LED
FREQ.
TRIPLER
FREQ.
DOUBLER
VOLTAGE
REGULATOR
FEEDBACK
REGULATOR
FREQ.
DOUBLER
RF
OUT
LIMITER
35 dB

4
CONTROLS AND FUNCTIONS
INPUT JACK
The input on the M187 accommodates virtually every lavalier, hand-held or shotgun microphone available. Use a
Switchcraft TA5F connector on the cord. See the separate sheet titled “M187 Input Jack Configuration” regard-
ing the correct connections for various microphones, and other sources.
ON/MUTE/OFF SWITCH
Turns the battery power on and off. The center position is an “audio mute”which should be used when setting the
MIC LEVEL control to turn off the sound from the microphone during this adjustment. When turning the transmitter
on, pause for a moment in the MUTE position to prevent a turn-on surge from occurring (a “thump”sound) in the
audio.
POWER ON/OFF LED
Glows brightly when battery is good. A weak or dim lamp means that the battery is weak, and has about an hour of
operation left (maybe a little more). If the lamp fails to light, the battery should be replaced. The power lamp should
light up in both the “mute”and “on”positions of the POWER/MUTE SWITCH.
The POWER LED is connected to a precision battery test circuit that continuously monitors battery voltage. The LED
is at full brightness with a new 9 Volt alkaline battery. As the battery voltage drops during use, the LED brightness will
also decrease. After 12 to 15 hours the battery voltage will be about 7 Volts and the LED will be completely out.
LECTROSONICS
M187
ON
MUTE
OFF
LEVEL
LIMIT
MIC LEVEL

5
Belt-Pack Transmitter
Rio Rancho, NM – USA
Since the internal circuits are all tightly regulated and the RF output stage has a separate discrete regulator, the
transmitter will continue to operate to a battery voltage of 6.5 Volts. From 6.5 Volts to 6 Volts, the transmitter will still
operate, but with degraded performance. Please note that a weak battery will sometimes light the POWER LED
immediately after turn on, but will soon discharge to the point where the LED will go out, just like a flashlight with
“dead”batteries.
The combination of an accurate battery condition indicator and regulation of all internal circuits provides much longer
battery life, as well as consistent performance over the life of the battery.
MODULATION LEDS
Indicate the proper setting of the MIC LEVEL control.
LEVEL LED
Flickers or glows when sufficient audio is present.
LIMIT LED
Lights up when the audio volume level is high enough to cause limiting.
MIC LEVEL
Used to adjust the audio input level for the proper modulation.
ANTENNA
The microphone cord is used as the antenna. A dipole antenna is formed between the shield of the microphone cord
and the metal transmitter housing.
THE BELT CLIP
The belt clip may be removed for special applications by removing the two screws.
USE ONLY THE SCREWS THAT ARE SUPPLIED
The circuitry is tightly packed into this unit. Longer screws will permanently damage the transmitter!

6
BATTERY REPLACEMENT
The M187 transmitter is powered by a standard alkaline 9 Volt battery. It is important that you use ONLY an ALKA-
LINE battery for longest life. Standard zinc-carbon batteries marked “heavy-duty” or “long-lasting” are not ad-
equate. They will provide only about 4 hours of operation. Similarly, ni-cad rechargeable batteries only provide 4
hours of operation or less, and will also run down quite abruptly. Alkaline batteries provide about 15 hours of opera-
tion.
To open the battery compartment, press outward on the cover door in the direction of the arrow as shown in the
drawing. Only firm, sliding pressure is needed to open and close the battery door.
Swing the door open and take note of the polarity marked inside showing the location of the positive (+) and negative (-
) terminals. Insert the battery correctly and close the cover by pressing the door closed and across, reversing the
opening procedure illustrated above. Don’t force the door closed. The terminals will hit a protective polarity barrier.
You can see the large and small contact holes inside the battery compartment.
Press outward on the
battery door in this
direction
Swing the
door open

7
Belt-Pack Transmitter
Rio Rancho, NM – USA
OPERATING INSTRUCTIONS
1) Insert the microphone plug into the input jack, aligning the pins; be sure that the connector locks in.
2) Turn the power switch to the “MUTE”position on the transmitter. The “MUTE”position allows internal voltages to
stabilize before audio signal paths are opened.
3) Position the microphone in the location you will use in actual operation.
4) Keeping the power switch in the “mute”position, speak as loudly as you expect you will in normal system use.
Rotate the MIC LEVEL knob so that the LEVEL LED flickers or stays lit as you speak. The LIMIT LED should light
up on loud “peaks.”Occasional lighting of the LIMIT LED indicates proper operation and optimum signal-to-noise
ratio. Even when limiting is occurring, little or no distortion will occur, due to the high linearity of the limiting
circuitry in the M187. The input limiter will cleanly handle peaks up to 35dB above full modulation.
5) Set up the receiver according to the receiver manual.
6) Move the switch to the “ON”position on the transmitter, verify that the modulation LEDs indicate normally and
adjust the volume of the sound system, or the record level of your recorder.
NOTE:
Do not use the MIC LEVEL control to control the volume of your sound
system or the record level on your recorder. This control
should be set only as described in #4 above.
If the mic level is too high —the LIMIT LED will light will light frequently or stay on. This condition may cause distor-
tion.
If the mic level is too low —neither LED will light or the LEVEL LED will light dimly. This condition may cause hiss
and noise in the audio.
The LEVEL LED turns on at -10dB below full deviation. The LIMIT LED turns on at full deviation and indicates that
the input shunt compressor is operating. The input compressor operates over a full 35dB range regardless of the gain
control setting. The compressor uses a true absolute value circuit to detect both positive and negative peaks. The
attack time is 2 milliseconds and the release time is 80 milliseconds. Occasional limiting is desirable, indicating that
the gain is correctly set and the transmitter is being fully modulated.

8
MICROPHONE CORD TERMINATION
1
23
4
5
VIEW FROM SOLDER
SIDE OF PINS
0.3"
0.15" Heatshrink
Tubing
TA5F Connector Assembly
Mic Cord Stripping Instructions
Caution!
Do not allow the shield wire to touch any
metal part of the connector shell.
The shield wire is the antenna on VHF
models and poor operating range will result.
Shield Wire
Crimp
Tabs
Rubber
Insulation
Crimp
Tabs
Rubber
Insulation

9
Belt-Pack Transmitter
Rio Rancho, NM –USA
M187 INPUT JACK WIRING
The wiring diagrams shown on the attached sheet represent the basic wiring necessary for the most common types of
microphones and other audio inputs. Some microphones may require extra jumpers or a slight variation on the dia-
grams shown.
Caution - When wiring the connector, do not use the connector body for any electrical connections.
A common mistake is to use the connector body as an audio ground. The connector body is
already used as an RF ground and no other use is permitted.
It’s virtually impossible to keep completely up to date on changes that other manufacturers make to their products. It
is possible that you may encounter a microphone that differs from these instructions. If this occurs please call our toll-
free number listed in the back of this instruction manual. Our service department can answer your questions regard-
ing microphone compatibility.
When used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmit-
ter. The nature of electret microphones makes them sensitive to RF, which can cause problems with the microphone/
transmitter compatibility. If the electret microphone is not designed properly for use with wireless transmitters, it will
be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret
capsule. These types of modifications are not shown on the attached instructions.
The M187 uses the shield of the microphone cord as the antenna. Other brands use a “dangling wire”to emit the RF
from the transmitter. There is really no difference between these two approaches, with respect to the effect of the RF
on the microphone capsule. Even in transmitters that utilize a “dangling wire,”the microphone is still part of the
“ground plane”and is therefore still in the antenna circuit.
For answers to questions regarding microphone/transmitter compatibility, call our service manager or engineering
department at the factory.
PIN 1 Shield (ground) for positive biased electret lavalier microphones. Bias voltage source for negative biased
electret lavalier microphones. Shield (ground) for dynamic microphones and line inputs.
PIN 2 Shield (ground) for negative biased electret lavalier microphones. Bias voltage source for positive biased
electret lavalier microphones.
PIN 3 Low impedance microphone level input for dynamic microphones. Also accepts hand-held electret micro-
phones provided the microphone has its own built-in battery.
PIN 4 1K ohm source load for non-Lectrosonics electret microphones. Use in conjunction with other pins to provide
attenuation of high level input signals.
PIN 5 High impedance, line level input for tape decks, mixer outputs, musical instruments, etc.
Transmitter
Input Jack
43
2
1
5
LECTROSONICS
1uH
10K
1K
5
510
4
3
2
1
60NH
330PF
330PF
185/187 Series
Transmitter Equivalent Input Circuit
+
5V Mic Bias
5mA max
To Mic Amp
POS BIAS (OR GND)
MIC
SOURCE LOAD
LINE IN
NEG GND (OR BIAS)
RF to Antenna
(mic cord)

10
RF BYPASSING
Some mics require RF protection to keep the radio signal
from affecting the capsule, even though the transmitter
input circuitry is already RF bypassed (see schematic
diagram).
If the mic is wired as directed, and you are having
difficulty with squealing, high noise, or poor frequency
response; RF is likely to be the cause.
The best RF protection is accomplished by installing RF
bypass capacitors at the mic capsule. If this is not
possible, or if you are still having problems, capacitors
can be installed on the mic wires inside the TA5F connector housing.
Install the capacitors as follows: Use 330 pF capacitors. Capacitors are available from Lectrosonics. Please specify
the part number for the desired lead style.
Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330P
All Lectrosonics lavalier mics are already bypassed and do not need any additional capacitors installed for proper
operation.
BODY GROUND
Caution - When wiring the connector, do not use the connector body for any electrical connections. A common
mistake is to use the connector body as an audio ground. The connector body is already used as an RF ground on
VHF models and no other use is permitted.
LINE LEVEL SIGNALS
The normal hookup for line level signals is: Signal Hot to pin 5, Signal Gnd to pin 1, pin 4 jumped to pin 1, and pin 3
jumped to pin 1. This gives a 30dB attenuator that allows signal levels much higher than 3V to be applied without
distortion.
If more headroom is needed, insert a 100k resistor in series with pin 5. Put this resistor inside the TA5F connector to
minimize noise pickup.
If lower than normal line levels (less than 1V) are expected, use this hookup: Signal Hot to pin 5, Signal Gnd to pin 1,
and pin 4 jumpered to pin 1. This provides a 20dB attenuator allowing signals as high as 3V to be applied without
distortion.
WIRING HOOKUPS FOR DIFFERENT SOURCES
3 WIRE MIC2 WIRE MIC
CAPSULE CAPSULE
SHIELD
AUDIO
SHIELD
AUDIO
BIAS
TA5F
CONNECTOR
TA5F
CONNECTO
R
Preferred locations for bypass capacitors
Alternate locations for bypass capacitors
PIN
5
4
3
2
1
SHIELD
AUDIO
BIAS
3
WIRE ELECTRET MIC
POSITIVE BIAS
1
2
3
45
TA5F
PLUG
1
2
3
4
5
PIN
SHIELD
AUDIO
2 WIRE ELECTRET MIC
POSITIVE BIAS
1
2
3
45
TA5F
PLUG
1
2
3
4
5
PIN
SHIELD
BIAS
AUDIO
3
WIRE ELECTRET MIC
NEGATIVE BIAS
1
2
3
45
TA5F
PLUG
1
2
3
4
5
PIN
SHIELD
AUDIO
2 WIRE ELECTRET MIC
NEGATIVE BIAS
1
2
3
45
TA5F
PLUG
SHIELD
TIP
PIN
5
4
3
2
1
SLEEVE
LINE LEVEL
RCA or 1/4 " PLUG
AUDIO 1
2
3
45
TA5F
PLUG
3
1
2
DYNAMIC
MIC LEVEL
1
2
3
4
5
3
2
1
PIN PIN
SHIELD
Dynamic LO Z mic or electret with
manufacturers power supply.
1
2
3
45
TA5F
PLUG

11
Belt-Pack Transmitter
Rio Rancho, NM –USA
TROUBLESHOOTING
Before going through the following chart, be sure that you have a good battery in the transmitter the red power LED
on the transmitter panel should glow brightly.
SYMPTOM POSSIBLE CAUSE
TRANSMITTER BATTERY LED OFF 1)Battery is inserted backwards.
2)Battery is dead.
NO TRANSMITTER MODULATION LEDs 1)Gain control turned all the way down.
2)Battery is in backwards. Check power LED.
3)Mic capsule is damaged or malfunctioning.
VERY SHORT OPERATING DISTANCE 1)Mic cord not properly terminated. Shield wire may be touching the
connector shell. See page 7.
NO SOUND IS HEARD AND 1)Transmitter not turned on.
RECEIVER RF LAMP IS OFF 2)Transmitter battery is dead.
3)Receiver antenna missing or improperly positioned.
4)Transmitter and receiver not on same frequency. Check labels on
transmitter and receiver.
5)Operating range is too great.
NO AUDIO IS HEARD BUT RECEIVER 1)On/Off switch is in “mute”position
RF LED IS ON receiver or transmitter.
2)Microphone on/off switch is in “off”position.
NOTE: If the modulation level 3)Volume is turned down or off on transmitter or receiver.
LEDs on the receiver are 4)Receiver not properly connected to other audio equipment.
indicating properly, the problem 5)Transmitter POWER switch may be turned on and off (i.e. through
is NOT in the transmitter. the mute position). A “thump”should be heard in the sound, again
indicating a properly functioning receiver.
NO SOUND AND RECEIVER 1)Transmitter audio muted. Make sure front panel power
MOD LEVEL LEDs ARE OFF switch is in the on position.
NO SOUND BUT RECEIVER 1)Receiver audio is muted. Refer to receiver manual.
MOD LEVEL LEDs ARE ON 2)Receiver audio output is disconnected or cable is
defective or mis-wired.
3)Sound system or recorder input is turned down.
NOISE (HISS) IS HEARD ALONG 1)MIC LEVEL is too low.
WITH THE SIGNAL 2)Transmitter and receiver may be too far from one another.
3)Receiver antenna may be defective or disconnected.
DISTORTED SOUND 1)MIC LEVEL is too high.
2)Mic may be distorting; try a different mic and listen again.
3)PA system may be overloading.
EXCESSIVE FEEDBACK 1)Transmitter gain (audio level) too high. Check gain adjustment
and/or reduce receiver output level.
2)Microphone too close to speaker system.
3)Microphone too far from user’s mouth.
4)Sound system volume set too high.

12
SPECIFICATIONS AND FEATURES
Operating frequencies: 150 to 216 MHz
RF Power output: 50 mW
Deviation: ±15kHz (max)
Spurious radiation: 55 dB below carrier
Equivalent input noise: -126 dBV
Input level: Nominal 2 mV to 300 mV (before compression)
30 Volt max. input level (including limiter)
Input impedance: Selectable for 500, 1K, 10K Ohm
Input compressor: Soft compressor, 35dB range
Gain control range: 43 dB; semi-log rotary control
Modulation indicators: Dual LEDs indicate modulation level and onset of limiting
Controls: 3 position “OFF-MUTE-ON”for noiseless operation
Front panel knob adjusts audio gain
Audio Input Jack: Switchcraft 5 pin locking (TA5F)
Antenna: Dipole radiator formed by mic cord shield and
transmitter housing
Battery: Precision compartment auto-adjusts to accept any known
alkaline 9 Volt battery (We’ve tried 107 of them!)
Weight: 5.3 ozs. including battery
Dimensions: 3.1 x 2.4 x .75 inches
Emission Designator: 54KOF3E
Specifications subject to change without notice.

13
Belt-Pack Transmitter
Rio Rancho, NM –USA
SERVICE AND REPAIR
If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment
needs repair. Make sure you have followed the setup procedure and operating instructions. Check out the inter-
connecting cords and then go through the TROUBLE SHOOTING section in the manual
We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop
attempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connec-
tion, send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set
at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment.
There are no adjustments inside that will make a malfunctioning unit start working.
LECTROSONICS service department is equipped and staffed to quickly repair your equipment. In-warranty repairs
are made at no charge in accordance with the terms of the warranty. Out of warranty repairs are charged at a modest
flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does
to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone
for out of warranty repairs.
RETURNING UNITS FOR REPAIR
You will save yourself time and trouble if you will follow the steps below:
A. DO NOT return equipment to the factory for repair without first contacting us by letter or by phone. We need to
know the nature of the problem, the model number and the serial number of the equipment. We also need a
phone number where you can be reached 8 am to 4 pm (Mountain Standard Time).
B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed
your repair through our receiving and repair departments. The return authorization number must be clearly
shown on the outside of the shipping container.
C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the
proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed”for
safe transport.
D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-
age to equipment that you ship. Of course, we insure the equipment when we ship it back to you.
Mailing address: Shipping address: Telephones:
Lectrosonics, Inc. Lectrosonics, Inc. [phone]
PO Box 15900 581 Laser Rd. [phone]
Rio Rancho, NM 87174 Rio Rancho, NM 87124 FAX: [phone]
USA USA
World Wide Web: http://www.lectrosonics.com email: [email protected]

LIMITED ONE YEAR WARRANTY
The equipment is warranted for one year from date of purchase against defects in
materials or workmanship provided it was purchased from an authorized dealer. This
warranty does not cover equipment which has been abused or damaged by careless
handling or shipping. This warranty does not apply to used or demonstrator equipment.
Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any
defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot
correct the defect in your equipment, it will be replaced at no charge with a similar new
item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.
This warranty applies only to items returned to Lectrosonics, Inc. or an authorized
dealer, shipping costs prepaid, within one year from the date of purchase.
This Limited Warranty is governed by the laws of the State of New Mexico. It states the
entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any
breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR
ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT
SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL,
OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE
THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF
LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE
EQUIPMENT.
This warranty gives you specific legal rights. You may have additional legal rights which
vary from state to state.
LECTROSONICS, INC.
581 LASER ROAD
RIO RANCHO, NM 87124 USA
November 1, 2001
LIMITED ONE YEAR WARRANTY