8. Other Special Functions:
A. Reset Function:
Long press “On/Off” key and “Number 8” key simultaneously for about 3 seconds. The remote will turned off
automatically and will do reset for about 1 minute. Restart the remote for use after.
B. Check and Edit the frequency Point on the Remote:
Feature:
1. Revising the frequency point to eliminate the external disturbance. 12 revisable frequency points for user.
2. Multiple remotes sync-control becomes available when they use the same frequency point
Note: After reset or revised the frequency points in the remote, receivers only can be used after pairing with them
Check the Frequency Point on the Remote:
Turn on the remote, long press the “On/Off” key for 5 seconds until the red light on indicator ashes 3 times, and
then green light on indicator ashes, the numbers of green ash will be the frequency point of the remote. Frequency
points editable after 3 seconds.
Edit the Frequency Point on the Remote: In frequency changing state,
Method 1: Short press any key from “1-8”, the frequency point will be “1-8” correspondingly, the green light will ash in
the same numbers. Then press any key or touch the color circle to exit the frequency edit state.
Method 2: Long press “On/Off” key for about 5 seconds, then green light on indicator will ash. The ash times plus 1
means the frequency point accumulate 1. Each time long press “On/Off” key over 5 seconds, the frequency point
will accumulate 1, which will again become value 1 when added to 12, and that cycles repeats.
9. Attention
ŸThe product shall be installed and serviced by a qualied person.
ŸThis product is suitable for dry locations. Avoid the sun and rain.
ŸGood heat dissipation will prolong the working life of the controller. Please ensure good ventilation.
ŸPlease check if the output voltage of any LED power supplies used comply with the working voltage of the product.
ŸPlease ensure that adequate sized cable is used from the controller to the LED lights to carry the current (min UL
listed 20 AWG wire)
ŸPlease also ensure that the cable is secured tightly in the connector to avoid the accidents due to overheat and
poor contact on the wire.
ŸEnsure all wire connections and polarities are correct before applying power to avoid any damages to the LED
lights.
ŸIf a fault occurs please return the product to your supplier. Do not attempt to x this product by yourself.
ŸKeep the Battery fully charged and charge twice monthly. Store it in a cool dry area.
10. Warranty Agreement
1). We provide lifelong technical assistance with this product:
ŸA 5-year warranty is given from the date of purchase. The warranty is for free repair or replacement and covers
manufacturing faults only.
ŸFor faults beyond the 5-year warranty we reserve the right to charge for time and parts.
2). Warranty exclusions below:
ŸAny man-made damages caused from improper operation, or connecting to excess voltage and overloading.
ŸThe product appears to have excessive physical damage.
ŸDamage due to natural disasters and force majeure.
ŸWarranty label, fragile label and unique barcode label have been damaged.
ŸThe product has been replaced by a brand new product.
3). Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
ŸWe will not be liable for any incidental or consequential damages for breach of any stipulation in this warranty.
4). Any amendment or adjustment to this warranty must be approved in writing by manufacturer only.
This manual only applies to this model. Changes can be made without prior notice.
www.ledworldlighting.com|www.ledworld.ca|1.800.387.4081 T4 2.4GHz LED RGB Controller
4/4
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
1
11. Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including
interference that may cause undesired operation.
Note: The manufactures is not responsible for any radio or tv interference caused by unauthorized modications to this
equipment. Such modications could void the user's authority to operate the equipment.
