LED World FC84M50-5M-24V-RGBW Installation instructions manual

LED WORLD INC. warranties this product for five year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or
implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This Limited Warranty does not apply to damage
caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them. This product must be used with LED
World’s class 2 power supply. Failure to do so will void limited warranty.
THREE YEAR LIMITED LIGHTING WARRANTY
LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase
of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory
of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental
breach) by led world inc or any person for whom led world inc is responsible, and even if led world inc has been advised of the possibility of such loss or damage being incurred.
If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number.
1/2 Copyright © 2021 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 - 03/29/21
Cutmark Cutting has to be straight No cut distortion
Do not bend 90° Do not bend Horizontally
Do not bend Horizontally Do not Twist Do not bend repeatedly
Architectural RGBW LED NEO-FLEX STRIP
Model: FC84M50-5M-24V-RGBW
LISTED
use only with
Class 2 Type
power units
24V
DC Power
5.6
WATTS
FOOT
Only power with 24VDC
Class 2 Power Source
For wet location installations,seal all possible water entry points and covers using silicone
Never plug into 120V AC. The product requires a optional class 2 Transformer.
This product is intended to be installed and serviced by a qualified licensed electrician. Install in accordance with the National Electric
Code, and local regulations. Only power with a (listed) constant voltage Class 2 power supply (24V DC).
Use only with LED World’s Class 2 Type power supply.
Disconnect power before installing or servicing (at breaker point).
Ensure the overall length of the neonflex does not exceed the maximum run length as 15m one end powered;30m two ends powered.
IMPORTANT INSTRUCTIONS
Please read instructions before using product and SAVE THESE INSTRUCTIONS. Before using this product make sure you have right color, product (item
number) and voltage (printed on product). Check for possibility of damage during shipping. If damaged, or wrong product, do not use. Disconnect power before
installing or using.
Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.
STATIC ELECTRICITY
CAN DAMAGE
PRODUCT
1-800-387-4081
ledworldlighting.com ledworld.ca |

TOOLS REQUIRED
Cutter RTV 108 Type silicone glue
INSTALLATION STEPS
Solder the wire
123
Use RTV 108 type silicon glue
to connect end
Complete connection
MOUNT NEO-FLEX STRIP INTO ALUMINUM CHANNEL/MOUNTING CLIP
Mounting clip comes with self-
lock bracket
1234
Aluminum channel comes with
self-lock bracket
Place the self-locking bracket
into the strip
Push strip into Mounting
clip/Aluminium channel
IMPORTANT INSTRUCTIONS
TROUBLESHOOTING
ŸThe power supply is not adequate for the length of LED Light Strips you are powering. Install a adequate Class 2 power supply.
Tape light strip does not light
ŸMake sure your power supply is turned on and has the correct voltage.
LEDs farthest from the power supply are noticeably dimmer
ŸThis is the result of voltage drop. Decrease the length of the 24V power feed or use thicker power feed wires between the 24V power
supply and the lighting strips.
ŸHave a electrician check all connections from the power supply to the LED Light Strips.
ŸConsider testing with a multimeter to ensure light strip is receiving 24V power.
LED Flex Strip lights blink on, then go off
1-800-387-4081
ledworldlighting.com ledworld.ca |
2/2 Copyright © 2021 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 - 03/29/21
Architectural RGBW LED NEO-FLEX STRIP
Model: FC84M50-5M-24V-RGBW