Ledj STAGE WASH U.V. 36 LEDJ106 User manual

www.prolight.co.uk
STAGE WASH U.V. 36
(order code: LEDJ106)
USER MANUAL

WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modifications to this equipment are not
subject to warranty.
STAGE WASH U.V. 36 Safety

STAGE WASH U.V. 36 Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modification to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to flammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualified engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualified
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.

STAGE WASH U.V. 36 Introduction
Introduction
CONTROL FEATURES
• 2-channel DMX
• Blackout/Dimmer/Strobe
Features
• 36 Ultra Bright 1W Ultra Violet LEDs
• Master/Slave functions
• Sound activated
• Rugged compact housing
• Consumption: 42W
• Beam 40 degrees
• Long life LEDs
DMX Channel Summary

STAGE WASH U.V. 36 Overview
Product Overview
Setup
Operating Instructions
The Stage Wash U.V. 36. is a DMX-512 controllable, unit made up of high efficiency and super
bright Ultra Violet LEDs.
The Stage Wash U.V. 36 will operate in stand-alone, Master/Slave, sound activated or via
DMX-512 control.
LED Display
Down
Button
Up
Button
DMX IN DMX OUTDMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT
Mode
Button Enter
Button

STAGE WASH U.V. 36 Operation Modes
Operating modes:
Brightness Mode:
To set the unit in brightness mode, press the mode button to show the last brightness setting
between “C-00 - C-99” on the LED display.
Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the brightness
output from 00-99. (00 = off, 99 = full on)
Strobe mode:
To set the unit in strobe mode, press the mode button to show the last strobe speed setting
between “F-00 - F-99” on the LED display.
Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the flash speed
from 00-99. (00 = slow, 99 = fast)
Sound Mode:
To set the unit in sound mode, press the mode button to show the last sensitivity setting between
“S-00 - S-99” on the LED display.
Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the sound
sensitivity level from 00-99. (00 = low, 99 = high)
DMX mode:
To set the unit in DMX mode, press the mode button to show the last DMX address setting
between “A000-A255” on the LED display.
Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the desired DMX
address from 000-255.
Slave mode:
To set the unit(s) in slave mode, press the mode button to show “SLAV” on the LED display.
The unit will now run in sequence with the master unit.
Note: After setting the desired setting always press the “ENTER” button a second time to
confirm your choice.
DMX function chart:

STAGE WASH U.V. 36 DMX Set Up
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each fixture requires a
“start address” from 1- 511. A fixture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a fixture that occupies or uses 7
channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the
controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The LEDJ Stage Wash U.V. 36 can be controlled via DMX-512 protocol. The DMX address is set
on the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR
connector for data input/output (figure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.

STAGE WASH U.V. 36 DMX Set Up
Notice:
• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

STAGE WASH U.V. 36 Specifications
Technical Specifications
Weight & Dimensions
• Length…........................................................... 300mm
• Width................................................................. 255mm
• Height…………………………………………….. 125mm
• Weight………………………………………......... 3.7 kgs
Power
• AC input…………………………………….......... 240V/50hz
Fuse
• Main………………………………………………. 20mm Glass 2A Fast Blow
Control & Programming
• Data input………………………………………... Locking 3-pin XLR male socket
• Data output………………………………………. Locking 3-pin XLR female socket
• Protocols………………………………………… DMX-512 USITT
• DMX channels…………………………………... 2