Ledj Spectra Par 6HEX10 User manual

Order code: LEDJ282
Spectra Par 6HEX10
Exterior Fixture
User Manual

www.prolight.co.uk Spectra Par 6HEX10 User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available mains supply voltage is
between 100~240V AC, 50/60Hz.
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• This lighting xture is for professional use only - it is
not designed for or suitable for household use. The
product must be installed by a qualied technician in
accordance with local territory regulations. The safety of
the installation is the responsibility of the installer. The
xture presents risks of severe injury or death due to re
hazards, electric shock and falls.
• Warning! Risk Group 2 LED product according to
EN 62471. Do not view the light output with optical
instruments or any device that may concentrate the beam.
• WARRANTY: One year from date of purchase.

www.prolight.co.uk Spectra Par 6HEX10 User Manual 3
Product overview & technical specications
The exterior Spectra Par 6HEX10 features 6 x 10W six-colour LEDs, delivering a smooth wash of colour,
ranging from intense, rich saturated hues through to pastel shades. Controllable via the onboard 4 button
LED menu system for auto, static colour or master/slave modes, with the option of DMX control for
larger installations. The silent running, convection cooled heavy-duty alloy enclosure features IP65 rated
connectors for both DMX and mains input/output.
• 6 x 10W six-colour LEDs
(RGBWAUV)
• Beam angle: 23°
• 1,626 Lux @ 2m (full on)
• 4kHz refresh rate
• DMX channels: 6/8 or 10
selectable
• Static colour, colour change, colour
fade and master/slave modes
• 0 - 100% dimming and variable
strobe
• 4 push button menu with LED
display
• IP rated power input/output trailing
connections
• IP rated 3-Pin DMX input/output
trailing connections
• Convection cooled
Spectra Par 6HEX10
Specications Spectra Par 6HEX10
Power consumption 60W
Power supply 100~240V, 50/60Hz
Dimensions 260 x 235 x 150mm
Weight 3.1kg
Order code LEDJ282
0m 1m 2m 3m 4m 5m
23°
23° - Lux
FULL ON
R
G
B
W
A
UV
6520
808
1810
240
2660
912
N/A
1626
202
452
60
666
228
N/A
724
89.8
201
26.7
296
101
N/A
408
50.5
113
15
167
57
N/A
261
32.3
72.3
9.6
107
36.5
N/A
150mm235mm
260mm
IP65
01 - Bracket
02 - Bracket tightening
knobs
03 - LED display
04 - Function buttons
05 - IP rated DMX input
06 - IP rated DMX output
07 - IP rated power input
08 - IP rated power output
In the box: 1 x xture,
1 x power cable &
1 x user manual
www.prolight.co.uk
02 02
03 04
01 01
05 06 0807

www.prolight.co.uk Spectra Par 6HEX10 User Manual 4
DMX channel mode:
Operating in a DMX control mode environment gives
the user the greatest exibility when it comes to
customising or creating a show. In this mode you
will be able to control each individual trait of the
xture and each xture independently.
To access the DMX channel mode, press the
“MODE” button on the rear of the unit to show
d001 on the LED display. Now use the “UP” and
“DOWN” buttons to set the desired DMX address.
Now press the “SETUP” button to choose one of the
6, 8 or 10 DMX channel modes, press the “SETUP”
button to conrm the setting. To exit out of any of
the above options, press the “MODE” button.
Operating instructions
6 channel mode:
Channel Value Function
1 000-255 Red (0-100%)
2 000-255 Green (0-100%)
3 000-255 Blue (0-100%)
4 000-255 White (0-100%)
5 000-255 Amber (0-100%)
6 000-255 UV (0-100%)
IMPORTANT! PLEASE NOTE:The LED display
for this xture has a menu locking function
where after 30 seconds ofinactivity it will lock.
To unlock the menu hold the “MODE” and
“DOWN” buttons for 3 seconds.
8 channel mode:
Channel Value Function
1 000-255 Master dimmer (0-100%)
2 000-255 Red (0-100%)
3 000-255 Green (0-100%)
4 000-255 Blue (0-100%)
5 000-255 White (0-100%)
6 000-255 Amber (0-100%)
7 000-255 UV (0-100%)
8 000-255 Strobe (slow-fast)
10 channel mode:
Channel Value Function
1 000-255 Master dimmer (0-100%)
2 000-255 Red (0-100%)
3 000-255 Green (0-100%)
4 000-255 Blue (0-100%)
5 000-255 White (0-100%)
6 000-255 Amber (0-100%)
7 000-255 UV (0-100%)
8
000 No function
001-020 Program 1
When
001-022
use CH9
for static
colours.
When
023-255
use CH9
for speed
(slow-fast)
021-041 Program 2
042-062 Program 3
063-083 Program 4
084-104 Program 5
105-125 Program 6
126-146 Program 7
147-167 Program 8
168-188 Program 9
189-209 Program 10
210-230 Program 11
231-255 Program 12
9
000 No function
Speed
(slow-fast)
when CH8 is
023-255
001-016 Red
017-033 Green
034-050 Blue
051-067 White
068-084 Amber
085-101 UV
102-118 Orange
119-135 Yellow
136-152 Magenta
153-169 Hot Pink
170-186 Cyan
187-203 Pastel Red
204-220 Pastel Green
221-237 Pastel Blue
238-254 Warm White
255 Cool White
10 000-255 Strobe (slow-fast)

www.prolight.co.uk Spectra Par 6HEX10 User Manual 5
Built-in program mode:
To access the built-in program mode press “MODE” until the display shows Pr.01 on the LED display.
Press “SETUP” to conrm the setting. Use the “UP” and “DOWN” buttons to select a program from
Pr.01 ~ Pr.12. Press the “SETUP” button to conrm the setting.
To change the speed of the selected program press the “SETUP” button and then use the “UP” and
“DOWN” buttons to select any value from SP00 ~ SP99. Press the “SETUP” button to conrm the
setting, then use the “UP” and “DOWN” buttons to select and value from F500 ~ F599 for the
strobe feature. Press the “SETUP” button to conrm the setting.
In Pr.01 you are able to set a specic static colour. When in Pr.01 press the “SETUP” button and
then use the “UP” and “DOWN” buttons to go through the static colours. Press the “SETUP” button to
conrm the setting, then use the “UP” and “DOWN” buttons to select and value from F500 ~ F599
for the strobe feature. Press the “SETUP” button to conrm the setting.
To exit out of any of the above options, press the “MODE” button.
Master/slave mode:
To set the master unit, press the “MODE” button on the rear of the master unit then select your desired
program (sound active, auto, static colour or one of the built-in programs). To set the other units in slave
mode, press the “MODE” button on the rear of the unit to show SLAu on the LED display and press
the “SETUP” button to conrm the setting. The units will now run in sequence with the master unit.
To exit out of any of the above options, press the “MODE” button.
Please ensure that all slave units are set to the same DMX channel mode as the master unit.
Operating instructions
Pr.01 Static colour
Pr.02 6 colour fade in/out
Pr.03 Colour fade in/out
Pr.04 Colour fade
Pr.05 6 colour change
Pr.06 Colour change
Pr.07 Red continuous fade
Pr.08 Green continuous fade
Pr.09 Blue continuous fade
Pr.10 White continuous fade
Pr.11 Amber continuous
fade
Pr.12 UV continuous fade
Programs: Static colours:
0.Off - Blackout
1.--r - Red
2.--g - Green
3.--b - Blue
4.--u - White
5.--A - Amber
6.--I - UV
7.-rg - Orange
8.-rg - Yellow
9.-rb - Magenta
10.-rb - Hot Pink
11.-gb - Cyan
12.-ru - Pastel Red
13.-gu - Pastel Green
14.-bu - Pastel Blue
15.-uu - Warm White
16.-cu - Cool White

www.prolight.co.uk Spectra Par 6HEX10 User Manual 6
Operating instructions
Auto mode:
To access the auto mode press “MODE” until the display shows Auto on the LED display. The xture
will now run through its built in programs Pr.02 ~ Pr.12. To exit out of any of the above options,
press the “MODE” button. NOTE: The user can set up the speed and ash speed for Pr.02 ~ Pr.12
under the built in programs mode. Changing this here will then take effect when running auto mode.
RGBWAUV colour mix mode:
To access the static colour mode press “MODE” until CoLr shows on the LED display.
Now press the “SETUP” button and use the “UP” and “DOWN” buttons to select the brightness
between r.000 ~ r.255. Press the “SETUP” button and repeat for green (G), blue (b), white (u) ,
amber (A) and UV ( I).
Value: 000 - 255 (000 = low brightness, 255 = high brightness)
To exit out of any of the above options, press the “MODE” button.
Factory reset:
To reset the xture to factory settings, power the xture off. Press and hold the “MODE” and “SETUP”
buttons whilst powering the unit up. Keep hold of the “MODE” and “SETUP” buttons for 3 seconds after
power up. The unit will now have reset to factory settings.
Built-in program Pr.01 Static colour
Pr.02 6 colour fade in/out
Pr.03 Colour fade in/out
Pr.04 Colour fade
Pr.05 6 colour change
Pr.06 Colour change
Pr.07 Red continuous fade
Pr.08 Green continuous fade
Pr.09 Blue continuous fade
Pr.10 White continuous fade
Pr.11 Amber continuous fade
Pr.12 UV continuous fade
SP00~SP99 (speed)
F500~F599 (ash)
RGBWAUV colour mix
mode
r.000~r.255 Red
g.000~g.255 Green
b.000~b.255 Blue
u.000~u.255 White
A.000~A.255 Amber
I.000~I.255 UV
Auto mode AUTO
Slave mode SLAu
DMX mode 6CH, 8CH, 10CH
Address setting d.001~d.512
Menu system

www.prolight.co.uk Spectra Par 6HEX10 User Manual 7
Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”
from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was
addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105
and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the
chain starts at 107.
DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent
xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.
DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”
XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).
DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest
cable path possible. The order in which xtures are connected in a DMX line does not inuence the
DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a
DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,
no matter where it is located in the DMX chain.
Also remember that DMX cable must be daisy chained and cannot be split.
DATA cable (DMX cable) requirements (for DMX operation):
This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.
DMX setup
Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers.
Please quote:
LEDJ 1m Interior -
Exterior DMX cable
LEDJ 1m Exterior
DMX cable
LEDJ 2m Exterior
DMX cable
LEDJ 5m Exterior
DMX cable
LEDJ 10m Exterior
DMX cable
Order code: LEDJ91 Order code: LEDJ141 Order code: LEDJ142 Order code: LEDJ143 Order code: LEDJ144
LEDJ 1m Exterior
Power cable
LEDJ 2m Exterior
Power cable
LEDJ 5m Exterior
Power cable
LEDJ 10m Exterior
Power cable
LEDJ Spectra Series
End Cap Set
Order code: LEDJ146 Order code: LEDJ147 Order code: LEDJ148 Order code: LEDJ149 Order code: LEDJ93

www.prolight.co.uk Spectra Par 6HEX10 User Manual 8
Notice:
Be sure to follow the diagrams below when making your own cables. Do not connect the cables
shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs
outer casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special note:
Line termination:
When longer runs of cable are used,
you may need to use a terminator on
the last unit to avoid erratic behaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a
3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
Termination reduces signal transmission
problems and interference. it is always
advisable to connect a DMX terminal,
(resistance 120 Ohm 1/4 W) between pin 2
(DMX-) and pin 3 (DMX+) of the last xture.
5-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Spectra Par 6HEX10 User Manual 9
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.

www.prolight.co.uk Spectra Par 6HEX10 User Manual 10

www.prolight.co.uk Spectra Par 6HEX10 User Manual 11

www.prolight.co.uk Spectra Par 6HEX10 User Manual 12