Ledj Spectra Batten User manual

www.prolight.co.uk
Spectra Batten
(Order code: LEDJ95)

LEDJ Spectra Batten Safety
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.

LEDJ Spectra Batten Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.

LEDJ Spectra Batten Over view
Over view:
Operation:
After the power is switched on, Press the “MODE” button to activate the main menu:
Built-in programmes mode, Auto run mode, DMX mode, Slave mode or Sound-active mode.
“SETUP” button is to change the parameter of the current mode.
“UP” button is to increase the value of the current setting.
“DOWN” button is to decrease the value of the current setting.
Built-in programmes: Runs one of the13 built-in programmes.
Auto run: Runs the built-in programmes in a continuous loop.
DMX mode: The unit can be controlled by any universal DMX controller.
Slave mode: The battens in this mode will be synchronously run with a batten
set to master mode.
Sound activated mode: Runs sound activated using the built-in microphone
Built-in programmes mode:
With the LEDJ indoor Spectra Batten, yon can select 13 different Programmes. Press the “SETUP”
and “UP” and “DOWN” buttons to select the programmes (from PG00 to PG12) and select the
desired programme value. When the LCD display shows PG- - (except PG00), press the “SETUP”
button for the rst time, and it will show SP.99, you can now select the running speed by using
the “UP” and “DOWN” buttons; then press the “SETUP” button for the second time, and it will show
FS.00, you can now select your desired ash frequency by using the “UP” and “DOWN”
buttons. But when in PG.00, press the “SETUP” button for the rst time, it will show C-.-1,

LEDJ Spectra Batten DMX Address Setting
Built-in programmes mode: (cont)
you can select the static color by using the “UP” and “DOWN” buttons. Press “SETUP” For a
second time, and it will show FS.00, you can then set the ash frequency by using the “UP”
and “DOWN” buttons, there is no speed function in this mode.
When it is set in PG05, press the “SETUP” button rst, and it will show C-.-1, then you can
select the moving colour by using the “UP” and “DOWN” buttons.
When it is set in PG06, press the “SETUP” button for the rst time, and it will show C1.-1, then
you can select the background colour, then for the second time, it will show C2.-1, you can now
select the moving colour by using the “UP” and “DOWN” buttons.
For example,
When the LCD display shows PG.01 , press the “SETUP” button for the rst time, and it will
show SP.99, you can now set the running speed for this programme. Then press the “SETUP”
button for a second time, and it will show FS.00, you can now select the ash frequency for it..
SP: Speed 00-99 (00 = slow, 99 = fast)
FS: Flash frequency from 00-99 (00 = slow, 99 = fast)
Auto run mode:
To access the Auto run mode, Press the “MODE” button until the LCD display shows AU.70, it
will now run through the built-in programmes automatically.
DMX mode:
To control the Spectra Batten individually via your DMX controller, press the “MODE” button untill
is shown on the LCD display, it is now in DMX mode. Now press the “SETUP” button
so the LCD display shows .001, this now means that the DMX address is set at 001. You can
select your DMX address by using the “UP” and “DOWN” buttons. If you press the “SETUP”
button the LCD display will show: 03.Ch., 09C.h. or P3C.h., this selects which DMX
mode the Spectra Batten is being run in. You can select any of these 3 DMX modes by using the
“UP” and “DOWN” buttons.
DMX Values
03CH
CH1
0 - 255
RED
CH2
0 - 255
GREEN
CH3
0 - 255
BLUE

LEDJ Spectra Batten DMX values
DMX Values: (CONT)
09CH
P3CH
Slave Mode:
To activate the Slave Mode, press the “MODE” button to show SlA-, this will now run
the Spectra batten in slave mode.
Sound Mode:
To activate the Sound Mode, press the “MODE” button to select SO.31, now the sound mode
is activated it will run one step at a time, you can adjust the sensitivity by using the “UP” and
“DOWN” buttons. (Sensitivity: SO01 - SO31, 01 = low, 31 = high)
CH1
0 - 255
RED 1
CH2
0 - 255
GREEN 1
CH3
0 - 255
BLUE 1
CH4
0 - 255
RED 2
CH5
0 - 255
GREEN 2
CH6
0 - 255
BLUE 2
CH7
0 - 255
RED 3
CH8
0 - 255
GREEN 3
CH9
0 - 255
BLUE 3
CH1
0 - 17: PG00
18 - 35: PG01
36 - 53: PG02
54 - 71: PG03
72 - 89: PG04
90 - 107: PG05
108 - 125: PG06
126 - 143: PG07
144 - 161: PG08
162 - 179: PG09
180 - 197: PG10
198 - 215: PG11
216 - 233: PG12
234 - 255 SOUND
CH2
0 - 255 select static colour
0 - 255 SPEED
0 - 255: SENSITIVITY
CH2
0 - 10: NO FLASH
11-255: FLASH
NOT USED

Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
LEDJ Spectra Batten DMX Set Up

LEDJ Spectra Batten Specications
Spectra Batten Specications:
LEDS: R:108, G:72, B: 72 (total: 252)
High intensity 10mm LEDs
Beam angle: 40 degrees
3 pin female XLR socket and 3 pin male XLR socket
3 pin XLR Power in and power out
Linkable via 3-pin XLR cable
Built-in microphone
Black aluminium material / White aluminium material
Working place: indoor, temperature: -20 °C~+ 45° C, humidity: 0%-90%.
LED display for easier operation.
Selectable built-in programmes mode, Auto run mode, DMX mode, Slave mode,
and Sound-activated mode.
Selectable 03CH / 09CH / P3CH DMX channels
Power consumption: 50W
Power supply: AC100-240V/50-60HZ
Size: 1070 x 65 x 88mm
Weight: 2.5kgs