Leedarson 8B-SS-ZF-H0 User manual

Content:
Water Leak Sensor ................................................................................................................................. 2
1. Product Introduction................................................................................................................2
2. Product Profile .........................................................................................................................2
3. Specification.............................................................................................................................2
4. Features/Capabilities: ..............................................................................................................4
5. Installation Notice....................................................................................................................4
6. Installation Guide....................................................................................................................5
7. Product usage .........................................................................................................................5
8. Note.........................................................................................................................................6
We build your success in IoT.

2
Water Leak Sensor
User Manual
1.Product Introduction
Using the LEEDARSON Water Leak Sensor and the LEEDARSON Application for your mobile device,
you can receive immediate alerts if a leak or flooding occurs in your home (such as in a basement,
near a water heater, under an old pipe, or in a bathroom). Early alerts can help you prevent leaks
from turning into flood situation, extensive property damage and excessive bills.
2.Product Profile1
Screw
(Remove screws and back cover to replace battery)
Reset button
Testing pin

3
Buzzer sound hole
Specification
Model Name
8B-SS-ZF-H0
Power Supply
Battery
Power Source
3V, AAA *2
Battery Life
5 years
Communication Protocol
Zigbee 3.0
Radio Frequency
2.4GHz
Wireless Range
100ft (40m)LOS
Operational Temperature
0℃- 40℃
Operating Humidity
Up to 85% non-condensing
Mounting
Floor type
Standards Compliance
FCC, CE RED
OTA
Yes

4
3.Features/Capabilities
The LEEDARSON Water Leak Sensor is a Zigbee compatible sensor.
The LEEDARSON Water Leak Sensor is powered by AAA battery with a 5-years battery life.
The LEEDARSON Water Leak “alarm” can be sent to Zigbee network devices or to any
compatible alarm system hub.
The LEEDARSON Water Leak Sensor is designed to be a floor type sensor..
The LEEDARSON Water Leak Sensor has a built-in LED indicator and an acoustic alarm.
The LEEDARSON Water Leak Sensor has a low battery alarm to Zigbee
Gateway/Hub devices
4.Installation Notice
1. Install the detector in areas where there is a concern about possible water leaks, such as
bathrooms, basements, water heaters, under clogged drains, under old pipes, or in other areas of
your home that are prone to leaking. You can receive an instant alert.
2. Do not locate the detector in cabinets and other areas where the alarm sound cannot be heard.
3. Do not install in an area where it can come in contact with rain, oil smoke and steam from a
kitchen range.
4. Do not install the detector in submersed water.
5. If a pool of water forms, moisture must contact both leads to trigger an alert.

5
6. Installation Guide
1. The sensor will be in pairing status when power turns on for the first time. This will cause an
LED indicator light to flash once per second for 3 minutes. Use the LEEDARSON Application to
search for this device.If sensor pairs successfully, the light will stop blinking and then stay on for
about 10 seconds.
2. Install the detector where there is a concern for a potential water leak.
7. Product usage
1. Insert 2 pcs AAA battery to the battery space, and the water leak sensor will be ready for use.
2. How to reset a water leak sensor
A. Press and hold the reset key on the bottom cover for about 3 seconds, then the LED
(signal light) will start blinking quickly.
B. Release the reset key and the sensor will be reset to factory settings and the LED(signal
light) blinks once per second to search for a new enabled Zigbee network.
3. How to pair a water leak sensor
A. After the sensor reset to factory settings, the LED(signal light) blinks once per second and
sensor starts searching an enabled Zigbee network.
B. If sensor pairs successfully, it will stop blinking and the light will stay on for 10 seconds
C. If no available networks were found within 3 minutes, the LED will stop blinking and turn
off.
Tip: When initially setting up the LEEDARSON Water Leak Sensor, it is recommended to perform the
setup task within 15 feet (4.5 meters) of the Zigbee Hub.

6
4. Once the sensor detects a water leak, the LED Indicator flashes and the alarm beeps once per
second. The alarm signal will be sent to the gateway once every 5 minutes. During the alarm status,
the user can mute the buzzer by using the App. If the sensor still detects a water leak after 10 minutes,
the detector will trigger the alarm again and another signal will be sent to the gateway and the user.
The alarm will be canceled if the situation as below.
①Water leak is controlled/stopped
②User presses the mute status by using the app
③The button on the sensor itself is pressed
④Power is turned off
Details about the alarm: there are four settings to select from in App.
⑤0: Buzzer muted, LED off
⑥1: Buzzer muted, LED flashes
⑦2: Buzzer on, LED off
⑧3: Buzzer on, LED flashes (Default setting)
6. When the battery voltage low, the detector will send a low battery signal to the gateway.
8. Notes
1. Replace the battery immediately when the low battery warning sounds to ensure the detector is
working properly.
2. Do not store any items on the surface of detector, as this may affect the sensors.
3. Clean the surface with soft towel regularly.
4. In the unlikelihood of a product failure, do not attempt to repair. Please contact the local
distributor.

7
Attention
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference. (2) This device must accept any
interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.

8
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
IC NOTICE TO CANADIAN USERS
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES‐003 (Cet appareil numérique de la Classe
B conforme à la norme NMB‐003 du Canada).
Hereby, Corporation declares that this device is in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU