LEGO Elsa's Magical Ice Palace 41148 User manual

Elsa's Magical Ice Palace #41148 Basic Version Lighting Kit
Package contents：
5 x 15cm Blue Dot Lights
2 x 30cm Blue Dot Lights
2 x 15cm White Dot Lights
1 x White Strip Light
2 x 15cm Connecting Cables
2 x 6-port Expansion Boards
1 x AA Battery Pack
Extra LEGO pieces
Note:
Place wires on the surface or under the LEGO building blocks.
The wire can be place between the building blocks or under the block, but they should be
placed between the studs correctly.
Insert the connectors to the ports.
Be careful when you are operating, there’s only one correct way to insert, make sure the
expansion board is upward, find the soldered “=” sign on the left of the port. When you
are inserting, the side which the wires can be seen should be faced to the “=” sign and
if you feel hard to insert, please stop, and don’t force it, for that may result in bent
pins inside the port or overheating of the expansion board.

At this point, use the tweezers to straighten the bent
pins.
When installing dot lights, make sure they are correctly placed (Yellow LED package is
exposed). You can put they either on the top of the studs or between studs.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.

Finally, please pay attention to the positive and negative terminals of the battery
when installing the battery case.
OK, Let’s Begin!

Instructions for installing this kit
Divide the building into 2 parts. Start from the first part.
Remove the snowflake piece from the top, take a 15cm blue dot light
Thread the connector of the light through the blue piece, pull the cable out till the light
is facing up

Reconnect the snowflake piece, place the cable behind
Remove and disassemble the lamp as per below
Take a 15cm white dot light

Thread the connector through the snowflake piece, pull till the light is facing up
Connect this section as per below
Take another 15cm blue dot light, thread its connector through the following trans blue piece

Thread the cable of the white light through the trans blue piece, reconnect the lamp, wind
the 2 cables together
Reconnect the lamp, place the cables behind
Take a 6-port expansion board, take the battery pack, inserted with batteries, connect the
cables of the lights we installed to the expansion board, turn the power on to test the current

Take a 15cm blue dot light, remove the following pieces

Connect the dot light as per below, hide the cable underneath the baseplate behind

Turn the building to its back
Place the cable as per below to hide it

Similarly, connect another 15cm blue dot light to the same position at the other side
Remove the following piece to hide the cable of the light from the top underneath, twist
the cables into a larger one

Connect the cables to the 6-port expansion board
Remove the following pieces, place the expansion board at the space per below

Connect the cable from the right to the lowest port
Take a 1x2 white plate（The transparent parts in the figure below are for demonstration
purposes only）, connect the cable from the left to the expansion board, secure the cable
in place by connecting the trans piece over
Take a 15cm connecting cable, connect it to the remaining port, secure it in place as we
did in the previous step

Take another 6-port expansion board, stick 2 adhesive tapes to its back
Turn the power on to check if all lights are working OK

Take a 15cm white dot light, a 2x2 round plate
Turn the first part of the building over, secure the light in the following place by connecting
the round plate over

Take a white dot light, a 15cm connecting cable, assemble them together as per below
Stick the strip light to the bottom of the baseplate, place the 15cm cable as per below,
group the cables together
Now, we finished installation for the first part, continue to install lights for the second
part, start from the lights in front of the door

Take 2 blue 30cm dot lights, 2 trans 1x1 plates, 2 trans 1x3 plates
Disconnect the following pieces
Connect the trans pieces as per below （The transparent parts in the figure below are for
demonstration purposes only）

Install the 2 blue 30cm dot lights to the following places
Reconnect the pieces we removed before, twist the 2 cables together

Lift the second part to thread the cables through the space underneath to the back，Pulled
into the room from the left stair gap
Disconnect the following piece and disassemble it as per below
Take a 15cm blue dot light

Connect it to the piece as per below
Reconnect the piece back, make sure the cable is facing inside of the room
Reconnect the 2 parts, pull the two 15cm connecting cables from the first part down to the
room below