LEGRAND CHIEF CSSMP15X10 User manual

INSTALLATION INSTRUCTIONS
Sliding Storage Panel
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CSSMP15X10

CSSMP15X10 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display, projector,
etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to accessory does not exceed 15 lbs
(6.8 kg).
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
--SAVE THESE INSTRUCTIONS--

Installation Instructions CSSMP15X10
3
DIMENSIONS
DIMENSIONS: INCHES
[MILLIMETERS]

CSSMP15X10 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité

Installation Instructions CSSMP15X10
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/2"
1/4"
Installation Hardware Kit
A (4)
[10-12 x 1"
G (1)
[CSSMP15X10 Storage Panel]
drywall anchor]
B (4)
#10 x 1"
C (2)
[Slot nut]
D (4)
5/16-18 x 3/8" E (20)
.625x.140x.031
F (2)
[Rivet]

CSSMP15X10 Installation Instructions
6
INSTALLATION
NOTE: The storage panel (G) may be installed using either of two methods. Proceed to either Installing Storage Panel to Wall
section OR Installing Storage Panel to Extrusion section.
Installing Storage Panel to Wall
NOTE: The storage panel (G) may be installed directly on the wall in one of two horizontal positions. (See Figure 1)
Figure 1
Horizontal Wall Mount - Right Horizontal Wall Mount - Left
The storage panel MUST be mounted
Clip
with the clip located at the bottom.
(G)
1. Determine location for the CMSSP15X10.
2. Using the CMSSP15X10 (G) as a template, mark the
locations of four mounting holes. (See Figure 2)
Figure 2
3. Drill four 1/4" pilot holes and insert drywall anchors (A) at
markings. (See Figure 2)
CAUTION: The storage panel must be mounted with the
clip at the bottom. (See Figure 1)
4. Fasten storage panel (G) to wall using four #10 x 1" Phillips
pan wood screws (B). (See Figure 2)
Installing Storage Panel to Extrusion
NOTE: The storage panel may be located anywhere along the
extrusion. For ease of use, it may be more convenient
to place it to the extreme left or right side of the
extrusion.
1. Remove screws and end cap from extrusion. (See Figure 3)
Figure 3
2
x 4
(G)
43
(B) x 4
(A x 4)
1
x 2 End cap
Extrusion

Installation Instructions CSSMP15X10
7
2. Insert four 5/16-18 x 3/8" button head cap screws (D) into
the two slot nuts (C) and partially tighten. (See Figure 4)
3. Slide two slot nuts (C) into end of extrusion. (See Figure 4)
Figure 4
CAUTION: The storage panel must be mounted with the
clip at the bottom. (See Figure 1) and (See Figure 5)
4. Hold the storage panel (G) over the four button head screws
(D) and lower the storage panel keyholes over the screws.
(See Figure 5)
Figure 5
5. Tighten screws securely against the storage panel.
Attaching Components
1. Remove mounting plate from storage panel by pressing
inward on the clip located at the bottom of the storage panel.
(See Figure 6)
2. Place component(s) on mounting plate and position in the
desired location with the hole pattern in mounting plate best
aligned to component mounting holes. (See Figure 6)
Figure 6
3. Using the fasteners provided with the component and the
washers (E), attach the component to the mounting plate.
(See Figure 6)
4. Return mounting plate to storage panel by installing the side
without the clip into the panel first, followed by the side with
the clip until it clicks into place. (See Figure 7)
5. OPTIONAL: If desired, install plastic rivet (F) into hole next
to clip to secure the mounting plate in place.(See Figure 7)
Figure 7
(C x 2)
2
2
(D x 4)
(C x 2)
Keyholes
5
(D) x 4
4
Clip
Component
Component
fasteners
3
Mounting
plate
1
(E)
Clip
Clip
5
Side with clip
Side without clip
OPTIONAL
Insert plastic
rivet

CSSMP15X10 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003122 Rev02
2019 Legrand | AV
www.legrandav.com
07/19