Leigh Country Amber-Log TX 36003 User manual

Take assembled SEAT PANEL (6) and one of the arm frames,
Attach the SEAT PANEL (6) to the inside of the arm frame,
secure with the indicated nuts and bolts.
Insert the other arm frame
on the other side and
secure loosely with
nuts and bolts.
Take the Lower Support
Beam (5) and secure
under the seat between
the arm frame with
nuts and bolts.
Once the bottom half is finished,
take the BACK PANEL (7) and
place it gently on part 4
of the arm frame.
Secure with indicated hardware
in the diagram.
Tighten all nuts, bolts,
and screws once
every part and
assembled pieces
are in place.
Congratulations
on your assembly!
STEP 2: Assembling the Bottom Half
STEP 3: Assembling the Upper Half STEP 4: Finish
Take one piece of the following parts with a letter “R” behind
each number: 1 , 2 , 3 , 4 , 8 (“R” = Right)
1: Part 1 to part 4
2: Part 3 to part 2
3: Part 2 to part 1
4: Part 4 to part 3
5: Part 8 to Part 2 & 3
Use indicated hardware,
directed by diagram.
REPEAT steps 1 through 5 above using parts labeled
with a letter “L” (“L” = Left) after the part number.
C
A
A
A
4R
3R
1R
8R
2R
7
BB
6
5
A
D
D
A
A
Left
Right
PORCH ROCKER
TX 36000, TX 36002, TX 36003,
TX 36004, TX 36005, TX 36007,
& TX 36008
A B C D
Mallet
Socket & Wrench
Phillips
Screwdriver
Tools Required for Assembly
13mm
NUT & BOLT
(8x120mm)
NUT & BOLT
(8x70mm)
SCREW
(4x40mm)
X 12pcs X 4pcs X 2pcs
SCREW
(8x120mm)
X 4pcs
Tools Included
IMPORTANT:
READ CAREFULLY BEFORE BEGINNING
Recessed Hole
Pre-Checked
PARTS AND HARDWARE LIST
1 2
6
3
7
4
85
ARM REST
LOWER
SUPPORT
BEAM
FRONT LEG
SEAT PANEL
DIAGONAL
SUPPORT
BACK PANEL
VERTICAL
SUPPORT
RUNNER
X 2pcs X 2pcs X 2pcs X 2pcs
X 1pc X 1pc X 1pc X 2pcs
1. Do not tighten bolts until fully assembled.
2. Rescessed holes to face outward.
3. Insert bolts with washer and secure with washer and nut.
4. Pre-checked side must always face downward or inward.
STEP 1: Assembling the Rocker Arm Frame
Power tools are not
recommended while
assembling this product.

© 2017 UGS Co., Inc. All Rights Reserved Patents Pending
DISTRIBUTED BY:
UNITED GENERAL SUPPLY CO., INC.
HOUSTON, TX 77036
www.LeighCountry.com
Limited Warranty and Care Instructions
LIMITED ONE YEAR WARRANTY (NON-TRANSFERABLE)
This product is covered under United General Supply’s (UGS) one (1) year limited warranty. To the
original purchaser of this piece of furniture, cooler or accessory; UGS warrants that it will be free
from defects in material and workmanship for up to one year from the date of purchase under
normal use and proper care.
Replacement of defective or missing parts will be sent at no charge to the customer for a period
of 30 days from the date of purchase. UGS will no longer be responsible for missing parts or
hardware 30 days after date of purchase. Freight, packaging, labor or material charges to and
from our customer service center is not covered under the warranty and is therefore the
customer’s responsibility.
The limited warranty does not cover this piece of furniture, cooler or accessory for commercial
purposes, abusive use, damage by modification, freeze damage, rust, fading and issues caused
by improper care.
For minor defects or missing parts/hardware, please contact customer service immediately upon
purchase. Please do not return product to the store unless the product is irreparable. A customer
service agent may help determine whether the damage is reparable and will provide further
instructions.
For returns and refunds, please refer to your local store return policy with proof of purchase.
Proof of purchase (dated register receipt) will be required for warranty claims.
The use of power tools during assembly may void this warranty.
PROPER CARE INSTRUCTIONS
Customer Service may be reached Monday through Friday from 9:00a.m. to 5:00p.m. CST.
[email protected] OR 1-877-87LEIGH (53444)
If left untreated, wood will naturally weather. During long periods of non-use, store furniture or cooler in
covered and dry place. For the least maintenance, place your furniture, cooler, or accessory under a
covered area.
To preserve and maintain the original finish of this cooler/furniture, a natural tung/linseed/Danish oil (with
stain), which can be found at your local hardware store, should be applied. Please note the cooler/furniture
has been stained and oiled before being packaged. If the wood is not maintained, the wood will naturally
grey in color.
Remove the cooler/furniture completely from sunlight prior to applying oil. Apply generously and remove
any excess oil with cloth. Frequency of the application of oil depends on exposure to the extremities of the
outdoors.