Leigh Country Char-Log TX 93605 User manual

TX 93605 SINGLE ROCKER WITH STAR
AssembleParts
ARM REST
LENGTH: 21.3” x 2pc
LENGTH: 28” x 2pc
LENGTH: 35.6” x 2pc
LENGTH: 22.5” x 1pc
ROCKER RUNNER
LOWER SUPPORT BEAM
x 1pc
SEAT PANEL
x 1pc
BACK PANEL
SCREW: S04-4 x 2pc
x 4pcNUT & BOLT: N08-8
0.3” x 3.1”
BACK
VERTICAL LOG
1
LENGTH: 25.6” x 2pc
FRONT VERTICAL LOG W/DOWELED
3
LENGTH: 28.3” x 2pc DIAGONAL
LOG
2
4
5
B
NUT & BOLT: N08-12 x 16pc
0.3” x 4.7”
A
C
7
6
8
STEP 1: Assembling the Rocker Arm Frame
Take one piece of the following parts with a letter
“R” behind each number: 1, 2, 3, 4, 5 (”R” = RIGHT)
1: Part 1 to part 4
2: Part 2 to part 3
3: Part 3 to part 1
4: Part 4 to part 2
5: Part 5 to part 2 and 3
Use indicated hardware, directed by diagram.
REPEAT steps 1 through 5 above using
parts labeled with a letter “L” (LEFT)
after the part number.
STEP 2: Assembling the Bottom Half
Take assembled SEAT PANEL (7) and one of the arm frames, keep the arm frame
standing and attached the SEAT PANEL (7) to the inside of the arm frame, secure with
the indicated nuts and bolts.
Insert the other arm frame
on the other side and
secure loosely with
nuts and bolts.
Take the lower support
beam and secure
under the seat between
the arm frame with
nuts and bolts.
STEP 3: Assembling the Upper Half
STEP 4: FINISH
Once the bottom half is finished,
take the BACK PANEL (8) and
place it gently on part 4 of the
arm frame.
Secure with indicated hardware
in the diagram.
A
8
A
Tighten all nuts, bolts,
and screws once
every part and
assembled pieces
are in place.
Congratulations
on your assembly!
1. Do not tighten bolts until fully assembled.
2. Recessed holes to face outward.
3. Insert bolts with washer and secure with washer and nut.
4. Pre-checked side must always face downward or inward.
IMPORTANT: READ CAREFULLY BEFORE BEGINNING!
Durable log construction.
Exclusive Char-log finish and design
Patent pending crack resistant design and process
Special Char-log heat curing, preserving, finishing
Process resists mildew, mold, and stains
Varnished to preserve Char-log finish
Recessed Hole
Pre-Checked
®
®
®

Limited Warranty and Care Instructions for CHAR-LOG Products
Limited one year Finish Warranty
** (non-transferable) **
This product is covered under United General Supply’s (UGS) one (1) year limited
warranty. To the original purchaser of this piece of Char-log furniture, UGS warrants that it
will be free from defects in material and workmanship for up to one year from the date of
purchase under normal use and proper care.
Replacement of defective or missing parts will be sent at no charge to the customer for a
period of 15 days from the date of purchase. UGS will no longer be responsible for missing
parts or hardware 15 days after date of purchase. Freight, packaging, labor or material
charges to and from our customer service center is not covered under the warranty and is
therefore the customer’s responsiblility.
The limited warranty does not cover this piece of Char-log furniture for commerical
purposes, abusive use, damage by modification, freeze damage, rust, fadding and issues
caused by improper care.
Proper Care Instructions
If left untreated, the wood will naturally weather. To preserve and maintain the original
finish, we recommend that a light lacquer coating be applied every 4 to 6 months
depending on the seasons. During a long periods of non-use, store furniture in covered
and dry place. For the least maintenance, use under covered area.
We recommend a exterior poly-urethane product that features a clear satin or semi-gloss
finish and a fast drying process.
Proof of purchase (date register receipt) and photos will be required for warranty claims.
For any questions or claims, please contact customer service.
Customer Service
1-877-87LEIGH (53444)
[email protected]
CCopyright U.G.S. Co., 2011
All rights reserved
Made in China
Distributed by:
United General Supply Co., Inc.
Houston, TX 77036
www.leighcountry.com
®
®
®