Leigh D4R Pro User manual

For the Leigh D4R Pro 24” Dovetail Jig
Joining Tradition with Today
Dedicated Customer Support
1-800-663-8932

CONTENTS AND STANDARDS
ii
D4R Pro User Guide
Preface Standards, Accessories and More.............................................iii
Chapter 1 Jig Assembly, Mounting, and Using The Clamps ......................1
Chapter 2 Adjusting the Finger Assembly..................................................7
Chapter 3 The Leigh eBush and Optional Guidebushes ............................9
Chapter 4 Basic Jig Functions and Scale Modes .......................................11
Chapter 5 Using Your Jig Safely................................................................13
Chapter 6 Wood Preparation ....................................................................15
Chapter 7 Router Preparation...................................................................17
Chapter 8 Through Dovetails....................................................................19
Chapter 9 Large and Small Through Dovetails ........................................29
Chapter 10 Variably Spaced Half-Blind Dovetails ......................................31
Chapter 11 Single Pass Half-Blind Dovetails ..............................................39
Chapter 12 Rabbeted Half-Blind Dovetails ................................................45
Chapter 13 End-on-End Dovetails...............................................................47
Chapter 14 Asymmetric Dovetails ..............................................................49
Chapter 15 Box Joints..................................................................................53
Chapter 16 Sliding Dovetails.......................................................................59
Chapter 17 Hints & Tips ...............................................................................65
Appendix I Attaching the Leigh eBush to the Router................................69
Appendix II Bit Selection ..............................................................................71
Appendix III Jig Parts .....................................................................................79
Appendix IV Customer Support ....................................................................83
TECHNICAL BULLETINS
Downloadable pdfs are available at leighjigs.com on the Support page for
these How To’s and more for your Leigh D4R Pro jig:
• Angled Through Dovetails
• Jumbo Half-Blind Dovetails
• Inlaid Through and Half-Blind Dovetails
• Needle Pins
• Through Dovetail Pins At Less Than 1" Centers
• Shelf Holes and Notches
• Clamp Short Boards on your Leigh Dovetail Jig – Quick Method
• Clamp Short Boards on your Leigh Dovetail Jig – Adjustable Width
The online video will reduce your learning time
dramatically! Stream to your smart phone or tablet to use in
your shop as a visual reference. Find the video in the Instructional
Videos section of the Support menu at leighjigs.com.
Watch the Online Instructional Video

iii
CONTENTS AND STANDARDS D4R Pro User Guide
Your New Leigh D4R Pro Dovetail Jig
Congratulations! You now own the world’s most useful and versatile dovetailing tool (and more!). The Leigh D4R
Pro Dovetail Jig will help you rout an infinite variety of joints, and all of its major functions are described in detail
in this guide. A very helpful DVD is also included, but the guide is essential reading.
Important! Inches and Millimeters
The D4R Pro jig can be ordered in inch or metric versions.
They’re identical except for the calibration scales. This Leigh
English-language user guide shows measurements in both inches
and millimeters, with “inches” first, followed by “millimeters”
in square brackets.
Example:
3⁄4"x 51⁄2"x8" [20x140x200mm]
Do not be concerned if the inch/millimeter equivalents are not
exact. Just use the dimensions which apply to your jig.
To simplify the instructions, most jig illustrations show a jig
considerably shorter than the standard 24"[610mm].
Where finger assembly scales overlay an illustration, the “inches”
scale ➀will be at the top, and “millimeters” scale ➁at the bot-
tom. Only the right hand “active” half of the scales are illustrated.
For clarity, setting positions are indicated with a red line in the
guide only. On the jig, the lines are black.
1
2
We recommend that you first assemble and mount the jig,
carefully following the instructions in the first section of the
guide. Then read the rest of the guide, following along with the
basic functions and principles of operation, before you try to
do any actual joinery routing. By all means, rout a few practice
joints in scrap boards before you use the jig to rout a precious
hardwood workpiece!
If you have any questions that are not answered in this guide,
please contact Leigh customer support:
Tel: [phone]
Tech Support: [email protected]
For more contact info, see Appendix IV – Customer Support
But remember:
“If at first you don’t succeed, read the instructions!”

CONTENTS AND STANDARDS
iv
D4R Pro User Guide
Glossary of Symbols
To help you understand the instructions and illustrations in this
manual, we have used a number of international symbols, plus
a few special ones of our own.They are all explained below. You
needn’t worry about memorizing these symbols now, because
they are repeated quite frequently in this user guide, and you
will soon get used to them.
The Leigh jig’s guidefinger assembly can be in any one of four
joint modes, depending on what type of joint and which part
of the joint you are routing. Each finger assembly scale has it’s
own mode icon ➀, identifying the joint part being routed. You
will also find the joint mode icon in the top left corner of most
illustrations ➁, indicating which finger assembly mode to use.
Sometimes a joint mode icon will be used to identify a board ➂.
These are the four joint mode icons:
TD Tails
(tails for through dovetail joints)
TD Pins
(pins for through dovetail joints)
HB Tails
(tails for half-blind dovetail joints)
HB Pins
(pins for half-blind dovetail joints)
2
3

v
CONTENTS AND STANDARDS D4R Pro User Guide
Which Way Round Should the Board Go?
As virtually all dovetail joinery is used to make boxes,
drawers and chests etc., we devised these simple (and
hopefully intuitive) icons to indicate which side of a
board faces inwards or outwards on the finished “box”,
and which side of the board faces outward (toward
you, the operator), when it is clamped in the jig.
The following symbols indicate:
eThis edge against sidestop
fThis edge against sidestop
Sawcut allowance
Caution: use special care for this
operation
➀➁➂ Numbered References in text
This icon oindicates the
“outside” of a board. All
through dovetail pin boards
are mounted in the jig with
this “outside” face away
from the jig (toward you, the
operator).
This icon iindicates the
“inside” of a board. All half-
blind pin and half-blind tail
boards, and through dovetail
tail boards, are mounted in the
jig with the “inside” face away
from the jig toward you, the
operator.
This icon jindicates boards
that are mounted both ways
e.g. sliding dovetails and end-
on-end dovetails.
Dotted line icons indicate
the “other” side of the board
in the illustrations.
Centerline of board or layout
Equals
Does not equal
Approximately

CONTENTS AND STANDARDS
vi
D4R Pro User Guide
Visit www.leighjigs.com for more details
Add Leigh Accessories to make your jig even more versatile.
Leigh Brand Bit Sets Offer Great
Savings...and the Box Is Free!
Save over individual bit prices. Each top quality
bit set includes a box with foam insert that
accepts all shank sizes, and a handy bit chart in
the lid to list out all the bit specs.
Item 1607-8 7-piece Bit Set
Item 2411-8 12-piece Bit Set
Item 5116-8 15-piece Bit Set
Combine the VRS with a Bit Set
for Exceptional Savings!
The D4R Pro Accessory Kit is the best deal going.
Enjoy great savings on the 12-piece Bit Set and
even greater savings when you combine it with
the VRSD24 Vacuum & Router Support.
Item ACD24
Finally, Dust-Free Routing
and Superb Router Support!
A must-have! The VRS Vacuum & Router
Support* is the ultimate dust and chip col-
lector. As an added bonus, the VRS adds
full width router support to your D4R
Pro. It’s simple to attach and the collec-
tor adapts to most popular vacuum hose
sizes.
Item VRSD24
* US patent: USPN 7,507,060 B2
UK patent: GB2446909

vii
CONTENTS AND STANDARDS D4R Pro User Guide
Visit www.leighjigs.com for more details
Optional Leigh Templates and Attachments
11 Sizes of Box/Finger Joints
Add an F3 Finger Joint Template* to your
D4R Pro Jig to make even more sizes of strong,
pleasing and easy box/finger joints. Rout
perfect joints in minutes, in sizes ranging from
3/32" to 1"[2 to 24mm].
Item F3 / F3M
* US Patent No. 5,711,356
Canadian Patent No. 2,146,834
European Patent No. 0698458
Six Unique Isoloc Joints,
Only from Leigh
The patented Isoloc joint gives any corner joint
a very unique look. These one-of-a-kind patterns
will really set your woodworking pieces apart
from the rest. Great savings when you buy all
three templates.
Items I1A, I1B, I1C and I13 (3 pack)
Classic Multiple Mortise
& Tenon Joints that Last
The Leigh M2 Attachment is the only one of
its kind. The multiple mortise & tenon joint is
ideal for “shelf to upright” construction and
produces extremely strong joints that stand the
test of time.
Item M2-24 / M2M-24
Need a Helping Hand?
Use Leigh Hold-Down Clamps
Leigh Hold-Down Clamps are tough, versatile and
immensely strong! They employ proven cam-action
technology developed for the award-winning Leigh
D4R Pro and FMT/Pro. Bench clamps can be used in any
size hole and surface clamps can be mounted on any
flat surface, both on any angle. You can never have
too many clamps!
Item BHDC1 Bench Mount
Item SHDC1 Surface mount

CONTENTS AND STANDARDS
viii
D4R Pro User Guide
Mortise & Tenon
Joints have never
been easier!
Leigh FMT Pro
Mortise & Tenon Jig
Item FMT Pro /
FMT Pro-M
Visit www.leighjigs.com for more details
Rout mortises and tenons in 60 seconds!
Leigh Jigs make it easy: One guide, one bit, one setup for
perfect joints every time. Make tables, chairs, beds, chests,
cabinets and so much more!
JIG FEATURES
• 68 joint sizes from 1/16"x1/8" up to 1/2"x5"
[79 metric joint sizes from 2x4mm up to
12 x130mm] using 21 standard guides (24
metric)
• Custom joint sizes up to 1/2"x5" [12 x130mm]
can also be achieved
• 6 optional specialty guides make square ten-
ons, louver doors, Y-axis 90º mortise
• Single, double (in line and side-by-side), triple,
quadruple joints
• Recordable, repeatable fit adjustment
• Angled and compound angled joints
• Works with virtually any plunge router
• Heavy gauge steel frame (Super FMT)
• CNC machined alumin. frame (FMT Pro)
• Multi-position clamping
• Clamp boards up to 3"x 5-1/2"[76x140mm]
• Easy and precise joint sighting
STANDARD EQUIPMENT
• Universal sub-base that attaches to virtually
any plunge router
• Two F-Clamps (Super FMT); Cam-action speed
clamps (FMT Pro)
• Joint guide stand
• 5/16" HSS spiral upcut bit, 1/2" shank
• Two outrigger bars (FMT Pro only)
• Adjustable side stop fence for tenoning
• Screwdrivers and mounting hardware
• Illustrated user guide

10
1 2 34
567 8
9
Jig Assembly, Mounting,
and Using the Clamps
D4R Pro - CHAPTER 1
Make Sure You Have All the Parts.
Before you start to assemble your Leigh D4R Pro, check to make sure you have received all the required parts.
The small carton you removed from the end of the main
carton contains:
1. 1 Leigh e7 eBush (elliptical guide bushing) and
pin wrench, 2 spacers
2. 2 dovetail bits, 1 straight bit, 1 collet reducer
3. 2 scale assemblies
4. 2 support brackets
5. 2 support bracket knobs
6. Square-head guide finger screwdriver
7. 4 clamp springs
4 clamp T-bolts
4 flat washers
4 T-bolt nuts
2 square nuts
1
5⁄64" hex key
1/4"-20 x ¾” Machine Screw (Accessory Attachment)
1 Leigh wrench/gauge
4 jig hold-down nuts & machine screws 1⁄4"-20
8. 4 cam-action speed clamps
4 cam clamp step washers
…and any other small optional items you may have ordered
with your new jig. Check the packing slip for this infor-
mation.
The main carton contains:
9. 1 main jig body
1 Leigh jig user guide
1 warranty/registration card
The large inner box contains:
10.1 finger assembly on 2 bars
D4R Pro has 26 guide fingers (13 pairs)
2 lengths bridge extrusion
1 sliding dovetail fence (cross cut fence)
1 nylon stop rod
2 clamp bars
If any items are missing from your jig, contact your
supplier or Leigh Industries immediately.
See Appendix IV, Customer Support.
Important Note
Mount your jig securely and assemble it completely before you try to
use it.
Make sure you have read and understood all the material in the Safety
section of this user guide before using the jig.
1
The online video will reduce your learning time
dramatically! Stream to your smart phone or tablet to use in
your shop as a visual reference. Find the video in the Instructional
Videos section of the Support menu at leighjigs.com.
Watch the Online Instructional Video

JIG ASSEMBLY, MOUNTING, AND USING THE CLAMPS
2
Chapter 1 D4R Pro User Guide
35/16"[84mm]
6"[150mm]+
295/16"[745mm]
37"[940mm]+
1"[25.4mm]
1
2
4
3
1-1 Prepare a flat board at least 3⁄4"[20mm] thick, and a mini-
mum of 37"x6"[940x150mm]. Drill four 9⁄32"[7mm] holes on
29 5⁄16"x 3 5⁄16"[745x84,2mm] centers, 1"[25.4mm] in from the
front edge of the board ➀. Countersink ➁or counterbore the
underside ➂if the board is thicker, so that the four 1⁄4-20x1" long
machine screws will project above the top surface by 3⁄8"[9,5mm] ➃.
1-2 Turn the jig body upside-down on two blocks ➀(to protect
the side stops). Using the four nuts and four countersunk machine
screws, bolt the base board to the jig using the two nut recesses in
each end housing. Holes drilled 1"[24mm] from the front edge
of the board go to the front of the jig. Now you can clamp your
D4R to any bench.
1
1-3 With the jig right side up, insert one square nut (part #284)
into each of the channels in the main extrusion. These nuts are
for possible future attachment of accessories. See Chapter 9.
1-4 Insert the four clamp T-bolts into the T-slots (two at each
end of the jig). Position so that the washers seat into the round
milled recesses. Tighten the four clamp bolt nuts with the Leigh
wrench.
1-5 Place four springs and two clamp bars on the T-bolts.
Make sure the clamp bars move freely on the T-bolts.
1-6 Place one black step washer ➀on each T-bolt with the
flat side against the clamp bar. Screw a clamp lever assembly onto
each T-bolt, making sure the cam lobes are between the step
washer sidewalls.
1

3
JIG ASSEMBLY, MOUNTING, AND USING THE CLAMPS Chapter 1D4R Pro User Guide
1-7 Insert the finger assembly support brackets. Note: The
right and left support brackets are NOT interchangeable.
Ensure the raised lug 2faces outwards when the bracket is
installed. For clarity, the set line 1is drawn in red. The actual
lines are black.
1
1-8 Place the finger assembly on your bench with the guidefinger
screws ➀on top and the pointed ends of the guidefingers away
from you. Fit the scales onto the finger assembly, placing the
HHB TAILS scale ➁to the right at both ends. Do not tighten
the scale set screws ➂yet. Note: The 1⁄4 " square half-blind pin bar
is supposed to be shorter than the finger bar. It is not inteneded
to fit in the scales at both ends.
2
3
1
2
3
1-9 Slide the complete finger assembly with loose scales onto
the support brackets. Set the bracket index line at 3⁄4 "[20mm] on
the HHB TAILS scale and tighten the thumbscrews ➀. Tighten
the scale screws ➁firmly with the hex key provided. If the scales
are removed from the finger bar for any reason, follow this
procedure to re-attach them.
1
2
1-10 Loosen the thumbscrews and make sure the finger assembly
slides on and off the support brackets smoothly, in both the tail
and pin modes. Move the outermost guidefinger at each end of the
finger assembly outward to touch the scales, and tighten. If fingers
do not slide easily, see note on page 7. This finger acts as an end
support for the router and is not generally used as a guide.
1-11 You will operate the cam-action speed-clamps every time
you use the jig, so get used to the feel of the clamps first. Use
some square ended boards for practice. Make sure the end of the
board is touching the underside of the guidefingers. Then slide
the board over against the side stop.
90˚
1-12 Do Not force the cam-action speed-clamp. It has great
leverage, and excessive force may damage the workpiece or the
jig.
IMPORTANT
2

JIG ASSEMBLY, MOUNTING, AND USING THE CLAMPS
4
Chapter 1 D4R Pro User Guide
1-13 A smooth, firm action is enough to engage the clamp.
Rule of thumb: If you can’t throw the lever comfortably by pressing
the end of it with your thumb, reduce the tension. A few minutes
of trial and error will help you feel the right clamp tension. Firm
thumb pressure is about right.
1-15 When engaged, the front clamp levers should point down
and the rear clamp levers should point away from the operator.
1-16 If the lever is badly positioned at the correct clamping
pressure...
1-17 Release the clamp, remove the board and turn the step
washer a quarter turn (the step height inside the step washer is
one quarter of the thread pitch).
1-18 Then adjust the clamp until the clamp lever is in the right
position at the right pressure.
1-14 Do Not use the lever as a torque arm. Adjust the clamp
tension only with the clamp disengaged.

5
JIG ASSEMBLY, MOUNTING, AND USING THE CLAMPS Chapter 1D4R Pro User Guide
1-19 For all but the wider workpieces, you need only operate
the clamp on the workpiece end ➀of the jig to release the board.
For narrower boards, the clamp at the free end ➁should be just
tight enough to bow the clamp bar about 1⁄8"[3mm] ➂greatly
exaggerated in this view.
1
2
3
1-20 Make up a spacer board. This board will be used to support
the finger assembly in all front-clamping vertical board modes.
The spacer board should be flat, straight and of even thickness.
We suggest 3⁄4 "x6"[20x150mm] by approximately 23" [580mm]
long. Note: the thickness of the spacer board has no relationship
to the thickness of the vertical board being routed.
1-21 After you have assembled and mounted the jig, you will
have some items left over:
1 straight router bit Leigh No.140-8
1 dovetail router bit Leigh No.80-8
1 dovetail router bit Leigh No.120-8
1 collet reducer
1 Leigh wrench/gauge (gauge: Ch.9)
1 accessory attachment screw (Ch.9)
1 hex key, allen wrench
1 Leigh e7 eBush (elliptical guide bushing)
1 pin wrench (eBush adjustment wrench)
1 Leigh guide finger adjustment screwdriver
2 spacers, one for single pass half-blind dovetails (Ch.11), and
one for box joints (Ch.15)
2 lengths of bridge piece extrusion (Ch.10)
1 sliding dovetail fence (cross cut fence) (Ch.16)
1 nylon stop rod (Ch.11)
1 fully illustrated user guide (this user guide)
Please keep all these items ready for use.
1 warranty card. Please register your warranty. You will auto-
matically be entered in Leigh’s Warranty Registration Contest.
1-22 To gain height for a more comfortable working position
or for routing longer boards, mount the jig to a box that can be
bolted securely to a bench.
See also fig.17-15. ■
1"[24mm]

JIG ASSEMBLY, MOUNTING, AND USING THE CLAMPS
6
Chapter 1 D4R Pro User Guide

7
2-1 Practice adjusting the finger assembly height. Loosen the
support bracket knobs and hold them firmly. Raise and lower the
assembly evenly, keeping it level, and tighten the knobs to lock it
at various heights.
2-2 Do Not raise or lower one end of the finger assembly at a
time.
2-3 To practice adjusting the guide fingers, put a board in the
front clamp. Always raise the finger assembly slightly, approxi-
mately 1⁄8"[2mm] above the spacer board and/or workpiece ➀.
This is essential to allow the guide fingers to move freely on the
guide finger bar and ensures that the fingers will be level and
flush when locked up. Move the guide fingers by pushing on the
middle to slide them along the guide finger bar.
11
2-4 Loosen about half the guide fingers and practice unlocking,
moving, positioning and re-locking them. Always press down
lightly on the center of each guide finger ➀when tightening
the screws.
If after loosening a finger it “sticks” and doesn’t slide, see header note
above.
1
Adjusting the
Finger Assembly
D4R Pro - CHAPTER 2
THE FINGER ASSEMBLY IS THE HEART OF THE LEIGH JIG.
Spend a few minutes now to familiarize yourself with these simple adjustments.
NOTE: The first few times you use your jig, some fingers may "stick". This is normal. To "unstick", loosen the finger
screw approximately 3/4 of a turn, and with the screwdriver still in the screw, press down firmly (on the screwdriver).
This will loosen the finger locking wedge (you may feel a click). The finger will now move freely.
7
The online video will reduce your learning time
dramatically! Stream to your smart phone or tablet to use in
your shop as a visual reference. Find the video in the Instructional
Videos section of the Support menu at leighjigs.com.
Watch the Online Instructional Video

ADJUSTING THE FINGER ASSEMBLY
8
Chapter 2 D4R Pro User Guide
2-5 Do not over-tighten the guide finger locking screws.The
Leigh screwdriver provided will give ample torque for easy lock-up
without strain.
2-6 Always tighten unused guide fingers before routing, as router
vibration will cause loose screws and wedge nuts to fall out and
be lost.
2-7 You can adjust the guide fingers by eye, or by measurement
to suit a set of plans.
Note: Always lower the finger assembly down onto the workpiece
before routing. ■

9
3-1 The Leigh e7-Bush ➀ is used to rout through, half-blind,
single pass half-blind and sliding dovetails, and also box joints on
the D4R Pro. The elliptical design provides precise joint fit adjust-
ment for box joints and sliding dovetails. A round 7/16"[11,1mm]
guidebush (min. barrel length 1/4"[6,35mm]) ➁ can be used to
rout through, half-blind, and sliding dovetails on the D4R Pro.
1 2
7/16
" [11,1mm]
[6,35mm]
1/4
" min.
3-2 The Leigh e7-Bush that comes with your D4R Pro is a
unique template guidebush that is adjustable in size. Unlike regular
circular template guidebushes ➀, the e7-Bush is slightly elliptical
in cross section ➁. This simple innovation effectively changes the
guidebush “active diameter size” when it’s rotated, and provides
benefits not possible with a standard round guidebush.
1
2
3-3 The e7-Bush ( 7/16") fits the router base or a guide bush
adaptor in the base (see Appendix I). The ellipse/oval shape has a
major axis ➀7/16"[11,1mm], and minor axis ➁7/16"[11,1mm] less
.020"[,5mm]. Turning the eBush 90ºin the router base changes
the active diameter by .020"[,5mm] providing minute adjustment
and recordable settings for perfectly fitting box joints.
1
21
2
7⁄16"[11,1mm] 7⁄16"[11,1mm] less .020"[,5mm]
3-4 Here’s how it works. In normal use on a dovetail jig, the
operator does not rotate the router more than a few degrees either
way ➀. In fact, because of potential bit-to-bush eccentricity prob-
lems it is advisable to minimize router rotation on jigs ➁.
1 2
The Leigh eBush and
Optional Guidebushes
D4R Pro - CHAPTER 3
The guidebush is the vital link between router and jig. All joints created on the D4R Pro are routed with the unique
e7* elliptical guidebush, a Leigh innovation that provides precise joint fit adjustment for box joints and sliding dovetails.
If your router doesn’t accept the e7-Bush, you can use an alternative guidebush with some limitations.
*Supplied with the D4R Pro. U.S. Patent No. 8,256,475. UK Patent No. GB2443974. Canada Patent No. 2,611,232
9
The online video will reduce your learning time
dramatically! Stream to your smart phone or tablet to use in
your shop as a visual reference. Find the video in the Instructional
Videos section of the Support menu at leighjigs.com.
Watch the Online Instructional Video

THE LEIGH e-BUSH AND OPTIONAL GUIDEBUSHES
10
Chapter 3 D4R Pro User Guide
12 o’clock position
1
3-5 Establish the orientation in which you normally hold and
operate the router on the jig. Now, up-end the router in the same
orientation. Make a small scratch line or permanent ink mark ➀
on the router base or eBush adaptor at the 12 o’clock position.
Learn about eBush adaptors on page 69.
3-6 Fit the e7-Bush to the router and align No.10 to the scratch
mark. This setting is used for all through and variably spaced half-
blind dovetails on the D4R Pro. Settings for single pass half-blinds,
box joints and sliding dovetails are described in applicable chapters.
Be sure to retighten the eBush nut after each adjustment is made
with the included pin wrench.
3-7 The bit goes through the e7-Bush ➀and fits in the router
collet or chuck.
1
3-8 The projecting part of the guidebush runs along the side
edge of the guide finger. The rotating bit cuts the wood only, and
touches neither the guidebush nor the guide surface. ■

D4R Pro CHAPTER 4
11
Here are the very basics for understanding the different D4R Pro dovetail modes and settings.
2. TD PINS
3. HB TAILS
4. HB PINS
1. TD TAILS
THE FOUR SCALE MODES
The Finger Assembly attaches to the support brackets in four
different modes to match the type of joint you are cutting.
Note: Inch scales are shown
here. Millimeter scales have
identical layout.
The active scale is always
on the right of each scale
assembly.
The inactive scale is always on
the left of each scale assembly
and is upside down.
Scales are color coded.
Silver background for
Through Dovetails.
Green background for Half-
Blind Dovetails.
The specific settings for each
scale are fully described in
the appropriate chapters.
Each scale has its own mode
icon (a drawing of the joint
part made in that mode).
This index line is used when setting the finger assembly
scales. The line is illustrated in red for clarity, but is black
on the jig.
Always read scales from
directly overhead to avoid
parallax problems.
All D4R Pro jigs are shipped
with “short” support brack-
ets.
The online video will reduce your learning time
dramatically! Stream to your smart phone or tablet to use in
your shop as a visual reference. Find the video in the Instructional
Videos section of the Support menu at leighjigs.com.
Watch the Online Instructional Video
Basic Jig Functions
and Scale Modes

BASIC JIG FUNCTIONS AND SCALE MODES
12
Chapter 4 D4R Pro User Guide
4-1 The two clamp bars hold workpieces horizontally or verti-
cally. The side stops align the boards in the correct position each
time.
4-2 The guidefinger assembly slides on to the support brackets
above the workpiece. The finger assembly is adjusted in or out
using calibrated scales on each end to suit different thicknesses of
vertical boards.
4-3 The finger assembly is raised or lowered using the support
brackets to suit different thicknesses of horizontal boards. ■