LEMI BELLAGIO 1M User manual

INSTRUCTION FOR USE ............................................................
ISTRUZIONI PER L’USO .............................................................
NOTICE D’UTILISATION .............................................................
BEDIENUNGSANLEITUNG ........................................................
pag. 3
pag. 13
pag. 23
seite. 33
ORIGINAL INSTRUCTIONS - REV. 1 / 2021
BELLAGIO 1M - VERSUS 1M

2
Congratulaon for having chosen an equipment LEMI produced by Brusaferri & C.
This table has been designed and built using state of the art technologies and processes to guarantee
the best reliability in the me and ensure maximum safety.
This table is suitable for cosmec face and body treatments, massages, SPA treatments, relax.
For a correct and safe operaon of the table is essenal to carefully read and observe what is indicated
in this manual. All documentaon accompanying the table – and in parcular this manual – must be
carefully preserved for future reference.
Complimen per aver scelto un’arezzatura LEMI prodoa da Brusaferri & C.
Questo leno è stato progeato e costruito ulizzando tecnologie e procedimen allo stato dell’arte
per garanrne la migliore adabilità nel tempo ed assicurarne la massima sicurezza.
Questo leno è adao per traamen esteci viso-corpo, massaggi, traamen SPA, relax.
Per un correo e sicuro funzionamento del leno è indispensabile leggere aentamente ed osservare
quanto indicato nel presente manuale. Tua la documentazione di corredo del leno - ed in parcolar
modo il presente manuale - deve essere accuratamente conservata per riferimen futuri.
Félicitaons d’avoir choisi un équipement fabriqué par Brusaferri & C.
Cee table a étée conçue et construite en ulisant des technologies et des procédés de qualité élevée
an de garanr la plus grande abilité à long terme et d’assurer la plus grande sécurité.
Cee table de massage a été conçue pour les traitements esthéques visage-corps, massages, relax.
Pour un bon fonconnement du fauteuil il est indispensable de lire aenvement et de respecter les
indicaons fournies par la présente noce. Toute la documentaon fournie avec la table doit être soi-
gneusement conservée pour ulisaon ultérieure.
Herzlichen Glückwunsch für eine Ausrüstung LEMI erzeugten von Brusaferri & C. gewählt zu haben.
Diese Liege wurde verwendend die modernster Technologien und Prozesse entwickelt und gebaut, um
die beste Zuverlässigkeit in der Zeit und die maximale Sicherheit zu versichern.
Diese Liege ist für ästhesche Gesichts- und Körperbehandlungen, Massagen, SPA- Behandlungen und
Entspannung geeignet. Für einen korrekten und sicheren Betrieb der Liege ist es wichg, was in diesem
Handbuch angegeben sorgfälg zu lesen und beachten,. Die ganze Unterlagen geliefert mit der Liege –
und insbesondere dieses Handbuch – es muss sorgfälg für die Zukun erhalten bleiben.
EN
IT
FR
DE

3
EN- INSTRUCTION FOR USE
INTRODUCTION
TRANSPORT AND INSTALLATION
ENVIRONMENTAL WORKING CONDITIONS AND STORAGE
PRELIMINARY CHECKS
DESCRIPTION OF THE TABLE
OPTIONS ON DEMAND
INSTRUCTION FOR USE
USE OF THE TABLE
MAINTENANCE
NOTICE TO OPERATORS AND RESIDUAL RISKS
SPARE PARTS
DISMANTLE
DISPOSAL OF OBSOLETE EQUIPMENT
DIMENSION
pag. 4
pag. 4
pag. 6
pag. 6
pag. 7
pag. 8
pag. 8
pag. 9
pag. 10
pag. 11
pag. 11
pag. 11
pag. 11
pag. 12
1.
9.
5.
13.
3.
11.
7.
2.
10.
6.
4.
12.
8.

4
1.2. Preservaon of the manual
This operang manual should be kept for future reference. We recommend:
1.1. Use purpose
The table has been designed and built to perform cosmec face and body treatments, massages, SPA treatments.
2.1. Handling and removal from the packaging
The table can be raised and moved manually by two or four people, taking it exclusively from the 4 support feet.
The table is shipped packed in a carton box. Open the box so you can freely raise the table; remove it from the packa-
ging, taking it from the 4 feet and pull it upwards.
The weight of the table is equal to 93 kg.
In the case of sale or transfer of the table to another person, this manual and its annexes should be delivered intact to
the new users.
Keep the manual in a place accessible and known to all operators, protected from moisture and heat and pro-
tected from the direct sun beams:
Use the manual in order not to damage any part of the content: do not remove, tear or modify any part of the
manual.
1. INTRODUCTION
2. TRANSPORT AND INSTALLATION
The successful and safe operaon of the table is guaranteed only if it is used in accordance with the
specicaons in this manual and, in general, in the accompanying documentaon; therefore it is
essenal to carefully read and keep all the relave documentaon. Although the table is equipped
with acve and passive safety features, not all risks can be avoided due to its incorrect use.
You must always make sure that all users have fully understood the rules of use; the manufacturer declines any respon-
sibility for damage to persons or property resulng from improper use of the device.
Do not remove or damage the labels, noces and warnings placed on side of the table. In case you need to restore
them, please contact the manufacturer. The manufacturer Brusaferri & C., declines any and every responsibility for fai-
lure to observe the rules of safety and prevenon described in the various secons of this manual and for any damage
caused by improper use. All works on the table (maintenance, adjustments, repairs, cleaning) must be carried out by
suitably trained personnel and in accordance with what is indicated in this manual.
WARNING! It is forbidden any use of the table other than that described in this manual. Brusaferri
& C. declines any responsibility for malfuncons or damages to persons or property due to uses
other than those specied in this manual. The table should be used only by personnel who are
informed about the use mode, operaon and its safety equipment.
WARNING! Please read this operaon manual before using the table. Anyone who uses the table
should be properly informed on the parts of this manual relevant to the operaons to be performed.

5
2.2. Flooring
The oor on which the table will be placed must be solid, smooth, horizontal and adequate to support its weight and
ensure the stability.
2.3. Lighng
The user must ensure that the lighng of the work areas is sucient to allow a good view of the operaons and all
elements of the table; the level of lighng should be in accordance with the UNI EN 12464-1; in parcular should be
avoided shadows and annoying glare.
2.4. Posioning
The posion of the table compared to xed obstacles must be such as to allow the easy passage for the use and
maintenance; in parcular, the minimum space to allow the passage of persons shall be equal to 650 mm (in accor-
dance with UNI EN 349:2008). To prevent crushing of the whole body the minimum distance between the leg rest
fully stretched and the back completely lowered and xed obstacles must be equal to 500 mm.
WARNING! It is strictly forbidden to remove the table by liing it from the top (maress).
WARNING! Do not use knives or box cuers to open the box so as not to risk damaging the
table and in parcular the pudding.
2.5. Power supply
The system of power supply must have voltage and frequency equal to the rated voltage and frequency of the power
supply of the device and be appropriate to the installed capacity, as indicated on the idencaon plate of the table.
Voltage
Frequency
Absorpon
Transformer
Duty cycle
110/240 V
50/60 Hz
3 A max
Primary 230V - 110V
Secondary 25V 120VA
18 o on - 2 min on
The power supply must be supplied to the unit by a line:
Protected against overcurrent by an automac circuit breaker (circuit breaker) or fuses, properly sized; the ope-
rang current of the protecons must be as low as possible taking into consideraon the maximum absorpon
of the device;
Equipped with a device sensive to insulaon failure (dierenal) with operang current low enough; this device
must be posioned downstream of the overcurrent protecve device (or be integrated with it); Having cables
with secon suitable for the power absorbed by the appliance.
The table must also be connected to an external unipotenal protecon circuit (grounding)
adequate.

6
2.6. Connecons
Insert the plug into a suitable power outlet.
If there is incompability between the socket and the plug of the table, replace the socket with
a suitable type by professionally qualied personnel.
PULL THE PLUG FROM THE POWER OUTLET GRASPING THE PLUG, NOT THE CABLE.
WARNING! It is strongly recommended to insert the plug into a single outlet exclusively reserved
to the device. We do not recommend the use of mulple sockets (power strip), adopters and patch
cords. The cable must not be bent.
WARNING! The table was not designed to work in environments with explosive atmospheres, in the
presence of ne dust or corrosive gases, in the presence of acids, corrosive agents, salt; it is also not
suitable for operaon in the presence of ionizing and non-ionizing radiaon (X-rays, laser, microwa-
ves, ultraviolet rays).
WARNING! Do not expose the table to an excessively humid environment. If the table gets wet, re-
move the plug from the outlet and have it checked by an Authorized Service Centre.
STORAGE! For the correct funconing of the electrical equipment the storage of the table must be
at a temperature between -25° C and +55° C, and only for short periods not exceeding 24 hours, to
+70°C. The table has no special requirements for storage, provided that it takes place in a closed and
dry rooms; this condion should also be ensured during all phases of transport.
The table has been designed and built to operate in a closed and dry room. The ambient operang condion are:
If the environmental condions are parcularly crical it is advisable to provide the room with an adequate air condi-
oning system to bring the humidity and temperature values within acceptable limits.
Temperature: 5° ÷ 40° C
Humidity: 30% ÷ 95% without condensaon
3. ENVIRONMENTAL WORKING
CONDITIONS AND STORAGE
4. PRELIMINARY CHECK
Before the seng at work of the table, make sure that:
There is no damage to the equipment due to the phases of transport and handling; eventually proceed to solve
these problems by contacng Brusaferri & C.;
All packaging components have been removed;
Check that the supply voltage is equal to the rated one as dened in § 2.5. Power Supply;
Check the eciency of the operaon of the control equipment.
Before using the table for the rst me, make sure qualied personnel carry out some tests in safety condions.

7
5. DESCRIPTION OF THE TABLE
Seat Legs
Adjustable feet
Wooden base with
adjustable height
Maress with
horseshoe headrest
Back
Predisposion for
roll holder
BELLAGIO 1M
Seat Legs
Pedal control
Adjustable feet
Wooden base with
adjustable height
Maress with
face hole
Back
Predisposion
for roll holder
VERSUS 1M

8
6. OPTION ON DEMAND
6.1. Heang
OFF = heang o (led: ON)
ON = heang on (led: ON + LOW)
LOW = low temperature 40° (led: ON + LOW)
HIGH = higher temperature 47° (led: ON + HIGH)
2H = heang is on for 2 hours (LOW or HIGH), then turn
o automacally.
When acvated, the led blinks ll the end of the se-
cond hour.
You can stop heang in any me pressing OFF buon.
Usually, heang stops automacally (LOW or HIGH
temperature) aer 1 hour from switch on.
The heang works with the pressure of the body, so we do not feel any sensaon of heat if it is not stressed by the
weight of a body. It is recommended to always leave a weight laid (for example towels or magazines) to maintain the
minimum temperature.
ATTENTION! It is absolutely necessary TURN OFF THE HEATING (OFF) WHEN THE TABLE IS NOT USED
AND AT THE END OF EACH WORKING DAY.
WARNING! During the funconing of the table the operator should always remain in the vicinity of
the controls; it is forbidden to leave the table unaended during its operaon.
6.3. Kit Chromo
If the table was equipped with chromotherapy strips, consult the
instrucon manual for the use of the remote control chrome.
6.4. Easy Move
To facilitate movement and cleaning, use the handle “Easy Move” by pulling
it towards you. The bed will slightly rise and will be easily movable by its ro-
tang wheels. Always restore the handle into its original posion at the end
of these operaons.
7.1. Operator
The table is controlled by an operator through the foot control pedal (or the hand control); the operator must posion
themselves so as to have complete view of the controlled parts and of the paent.
7. INSTRUCTION FOR USE
Press the buon on the right side of your table in order to acvate the Bluetooth. Search for the Blue-
tooth devices with your smartphone and select the preferred track to be played. Sound will come from
two speakers placed in the backrest of the table.
6.2. Bluetooth Sound kit

9
WARNING! Stretch out on the table always sing properly in the
central part of the seat.
Do not sit or lean on the side of the feet or of the head.
Operators should pay aenon to avoid creang potenally dangerous situaons for their own or
other’s safety.
All the people who work on the table must be properly trained on the correct methods of work and
informed about its proper funconing. They also need to be aware of the parts of this documenta-
on relevant to their work.
7.2. Use of maress
In order to ensure hygiene and safety to your paents and ensure long life of the maress, we recommend you always
cover it with a towel/bed cover and disposable sheets of cartene before starng any treatment.
Both the operator and the paent should not wear rings, necklaces, bracelets, watches or other objects that may da-
mage the maress.
7.3. Controls
The table can be controlled by a pedal with cable. All controls are maintained acon, that is releasing the control pedal,
the moon stops.
Pedal 1: Chair up
Pedal 2: Chair down
PEDAL WITH CABLE
7.5. Manual back adjustment
To raise the back rest, hold it with one hand and press the lever with the other hand. To lower the back rest (horizon-
tal posion), press the lever and push down the back.
8. USE OF THE TABLE
On the table, only one person can get up; the person must go up/down when the table is in the basic posion going
up on the seat.
200 kg (max. paent weight) 2500 N (Safety load)
1 2
7.4. Adjustment of the head (ONLY FOR BELLAGIO 1M)
The table is supplied standard with an horseshoe headrest, but on request it is
possible to add the head without a hole. The horseshoe headrest in parcular
allows the forehead to be supported so as to guarantee an opening sucient
to accommodate the paent’s nose when in a prone posion. The headrest
can be extended, removed or adjusted in dierent inclinaons by opening the
black handle placed near the headrest.

10
The table has been designed and constructed so as to reduce as much as possible the necessary maintenance and en-
sure proper funconing over the years without any problems. During any intervenon on the table, it is recommended
to follow the instrucons given in this secon.
9. MAINTENANCE
WARNING! All intervenons on the table must be carried out by competent and trained personnel
on the methods to operate correctly and safety. Do not make any acon on the table moving, and
always check that the plug connecng to power supply is disconnected; bring the power plug next
to you during the execuon of the intervenon on the table so you can check at any me the actual
separaon.
WARNING! The limbs of the paent must always be on the table.
The operator must always inform the paent when he moves the table.
WARNING! Be careful to make sure that the table or its electrical parts are not wet and that liquids
become not stagnant on the table itself; immediately wipe up any liquids – including physiological
liquids of the paent – which may end up on the table.
To avoid shock hazard, do not connect or disconnect the power plug with wet hands. Do not use
the table barefoot.
9.1. General Checks
Constantly check the general condion of the table: the integrity of the protecons, the electrical equipment and the
condion of the pads.
WARNING! Do not use the table if any component is found to be not perfectly intact or in service.
In this case, put the table out of service by disconnecng the power plug immediately and contact
an Authorized Service Centre.
9.2. Extraordinary Maintenance
Any extraordinary maintenance must be performed by qualied personnel of the technical service Brusaferri & C. or
Service Centre authorized by the manufacturer.
Informaon about the Authorized Service Centre to which you can turn, can be obtained directly from the manufactu-
rer Brusaferri & C srl – phone [phone] – mail: [email protected]
For a correct and quickly resoluon of the problem, it is necessary to communicate the model and the serial number of
the table and the descripon of the defect, or what are the visible problems, and under what condion it occurs. The
broken table, if under warranty, must be sent to the Service Centre together with the cercate of guarantee, transport
charges must be paid by the purchaser.
WARNING! Any form of warranty expires if intervenons are carried out on the table by so-
meone not authorized by Brusaferri & C.
9.3. Authorized Personnel
Repairs and maintenance of the table can be carried out exclusively by competent personnel, that is of Brusaferri & C.
or authorized by it. Informaon on the sta to contact for possible intervenons can be obtained directly from Brusa-
ferri & C.