LENCO TS-10 User manual

EN

1
What’s in the Box
Main Unit
3.5mm to 3.5mm Cable
(For TV Headphone Output)
Instruction Manual
AC Power Cable

Design and specications are subject to change without notice.

2
Safety
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near
water.
6 Clean only with dry cloth.
7 Do not block any ventilation
openings. Install in accordance
with the manufacturer’s instructions.
8 Do not install near any heat
sources such as radiators, heat
registers, stoves, or other apparatus
 (includingampliers)thatproduce
heat.
9 Protect the power cord from being
walked on or pinched particularly
at plugs,convenience receptacles,
and the point where they exit from
the apparatus.
10 Unplug this apparatus during
lightning storms or when unused for
long periods of time.
11Referallservicingtoqualied
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
12 Unit shall not be exposed to
dripping or splashing.
13 Do not place any sources of
danger on the apparatus (e.g.
 liquidlledobjects,lightedcandle).
14 The mains plug is used as the
disconnect device, the disconnect
device shall remain readily
operable.
Warning
1 Before operating this system, check
the voltage of this system to see if it
is identical with the voltage of your
local power supply.
2Do not place this unit close to
 strongmagneticeld.
3 If the system is brought directly
from a cold to a warm location,
or is placed in a very damp room,
moisture may condense on the
lens inside the player. Should this
occur, the system will not operate
properly. Leave the system turned
on for about an hour until the
moisture evaporates.
4 Should any solid object or liquid fall
into the system, unplug the system
 andhaveitcheckedbyqualied
personnel before operating it any
further.
5 Do not attempt to clean the unit
with chemical solvents as this might
 damagethenish.Useaclean,dry
or slightly damp cloth.
6 When removing the power plug
from the wall outlet, always pull
directly on the plug, never yank on
the cord.
Important Safety Instructions

3
Main Unit: Top View
1 /SOURCE
Select LINE IN 1 or LINE IN 2.
2 AUTO POWER Light
Indicate mode of auto power.
Red light: Standby mode.
Green light: play through LINE IN 1.
Yellow light: play through LINE IN 2.
3 + VOLUME -
Increase or decrease the volume
level.
Rear View
4 LINE IN Terminal
Connect to an external audio
device.
5 AC~
Connect to a power source.
Identifying the Parts

4
Connect to TV
This unit is very user friendly, please just
connect it directly to TV’s headphone
jack as below :
1 Connect the LINE IN cable to:
- LINE IN socket on the unit.
- HEADPHONE socket on TV.
2 Unit turn on automatically. Press
the /SOURCE button to select
source.
3 Turn on your TV.
Tip:
You can simply use your TV’s
inherent Remote Control set to
control Vol+/Vol-.
Connect Power
Caution:
- Risk of product damage!
- Ensure that the power supply voltage
corresponds to the voltage printed on
the back or the underside of the unit.
Connect the AC power cord to:
- the AC ~ socket on this unit.
- the wall socket.
Turn On/Off
When you connect TV or an
external device to the unit, unit will
turn on automatically. Auto Power
indication light is green (connect
to LINE IN 1) or yellow (connect to
LINE IN 2). And will turn red when
disconnected or when you turn off
TV / external device.
NOTE:
If the volume of TV or an external
device is too low, the unit also turn
off automatically.
Adjust Volume Level
During play, press the VOLUME+/-
buttons to increase/decrease the
volume level.
If the unit is connected to the TV’s
headphne jack, you can also
control the Volume Level by using
the TV’s remote control set directly.
Connections

5
Troubleshooting
To keep the warranty valid, never try
to repair the system yourself. If you
encounter problems when using this
unit, check the following points before
requesting service.
No power
- Ensure that the AC cord of the
apparatus is connected properly.
- Ensure that there is power at the
AC outlet.
- Press standby button to turn the
unit on.
No Response From the Unit
- Disconnect and reconnect the AC
power plug, then turn on the unit
again.
Specications
General
Power Requirements. AC 230V ~ 50Hz
Power Consumption .................... 6.5W
Output Power ..............7.5W x 2 + 15W
Total Harmonic Distortion .....................
..........................................1%(1kHz, 1W)
Audio Input Sensitivity/Impedance
LINE: ................................ 500mV/47kΩ
Frequency Response ............................
......................... 40Hz - 20kHz(+0 / -3dB)
Unit Dimensions (W x H x D)..................
.................................. 584 x 50 x 218mm
Speaker
Front
Impedance......................................3Ω
Rate Power .................................... 10W
Subwoofer
Impedance......................................6Ω
Rate Power .................................... 30W
If at any time in the future you should
need to dispose of this product
please note that: Waste electrical
products should not be disposed of
with household waste. Please recycle
where facilities exise. Check with
your Local Authority or retailer for
recycling advise. (Waste Electrical
and Electronic Equipment Directive.)