Lenel OnGuard 2013 User manual

PERPETUAL INNOVATION
2013
NGP Keypad Installation Guide

Lenel OnGuard®2013 NGP Keypad Installation Guide, product version 6.6
This guide is item number 55-3601E, revision 1.007, July 31, 2012
Copyright © 2010-2012 Lenel Systems International, Inc. Information in this document is subject to change without
notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, without the express written permission of Lenel Systems International, Inc.
Non-English versions of Lenel documents are offered as a service to our global audiences. We have attempted to
provide an accurate translation of the text, but the official text is the English text, and any differences in the
translation are not binding and have no legal effect.
The software described in this document is furnished under a license agreement and may only be used in accordance
with the terms of that agreement. Lenel and OnGuard are registered trademarks of Lenel Systems International, Inc.
Microsoft, Windows, Windows Server, and Windows Vista are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries. Integral and FlashPoint are trademarks of Integral
Technologies, Inc. Crystal Reports for Windows is a trademark of Crystal Computer Services, Inc. Oracle is a
registered trademark of Oracle Corporation. Other product names mentioned in this User Guide may be trademarks or
registered trademarks of their respective companies and are hereby acknowledged.
Portions of this product were created using LEADTOOLS © 1991-2012LEAD Technologies, Inc. ALL RIGHTS
RESERVED.
OnGuard includes ImageStream® Graphic Filters. Copyright © 1991-2012Inso Corporation. All rights reserved.
ImageStream Graphic Filters and ImageStream are registered trademarks of Inso Corporation.
Warranty
Lenel warrants that the product is free from defects in material and workmanship under normal use and service with
proper maintenance for one year from the date of factory shipment. Lenel assumes no responsibility for products
damaged by improper handling, misuse, neglect, improper installation, over-voltages, repair, alteration, or accident.
This warranty is limited to the repair or replacement of the defective unit. In no event shall Lenel Systems
International be liable for loss of use or consequential damages of any kind, however occasioned.
There are no expressed warranties other than those set forth herein. Warranty expressly excludes third party additions,
deletions and/or upgrades to this product, including those contained herein. Lenel does not make, nor intends, nor
does it authorize any agent or representative to make any other warranties or implied warranties, and expressly
excludes and disclaims all implied warranties of merchantability or fitness for a particular purpose.
Returned units are repaired or replaced from a stock of reconditioned units. All returns must be accompanied by a
return authorization number (RMA) obtained from the Lenel customer service department prior to returning or
exchanging any product. The RMA number must appear on the outside of the shipping box and on the packing slip.
Any items returned without an RMA number will not be accepted and will be returned at the customer’s expense. All
returns must have transportation, insurance, and custom brokers’ fees prepaid.
Liability
It is expressly understood and agreed that the interface should only be used to control exits from areas where an
alternative method for exit is available. This product is not intended for, nor is rated for operation in life-critical
control applications. Lenel Systems International is not liable under any circumstances for loss or damage caused by
or partially caused by the misapplication or malfunction of the product. Lenel’s liability does not extend beyond the
purchase price of the product.

NGP Keypad Installation Guide
revision 1.007 — 3
Table of Contents
Compliance Statements .......................................................5
1. Industry Canada Customer Information ............................................................ 7
1.1 Notices ................................................................................................. 7
1.2 Cautions ............................................................................................... 7
2. Customer Instructions Pertaining to FCC Regulations (North America) ........... 8
2.1 Notices ................................................................................................. 8
2.2 Cautions ............................................................................................... 8
2.3 Mains Supply ....................................................................................... 9
2.4 Warnings (North America, Australia) ................................................... 9
3. CE Conformity .................................................................................................. 9
Hardware Components ...................................................... 11
1. LCD Keypad Overview ................................................................................... 13
2. LCD Keypad Notes ......................................................................................... 18
2.1 When a Keypad Is First Powered ...................................................... 18
2.2 Main Test Menu Selections ............................................................... 18
2.3 User's Access Card Quick Enrollment ............................................... 19
2.4 Point Mapping .................................................................................... 19
3. NGP Controller ............................................................................................... 20
3.1 Mounting a Control Box ..................................................................... 20
3.2 Control Box Dimensions .................................................................... 20
3.3 Main Control Module .......................................................................... 21
3.4 Keypad Wiring ................................................................................... 22
3.5 World Wide Modem (2400 baud) ....................................................... 24
4. Wiring Specifications ...................................................................................... 26
5. Power Limits and Standby Power ................................................................... 27
5.1 Main Control Unit ............................................................................... 27
5.2 Power Supply Unit ............................................................................. 27

Table of Contents
4 — revision 1.007
Programming the System ................................................... 29
6. Programming the System Using the LCD Keypad ......................................... 31
6.1 LCD Keypad ...................................................................................... 31
7. Manually Calling the Access Control PC From the LCD Keypad ................... 35
Diagnostics ......................................................................... 37
8. Diagnostics ..................................................................................................... 39
UL Listed Systems ............................................................. 41
9. UL Systems: Notes ......................................................................................... 43
9.1 Installation Notes ............................................................................... 43
9.2 Programming Notes ........................................................................... 43
10. UL Systems: Requirements .......................................................................... 44
10.1 Entry and Exit Delays ...................................................................... 44
10.2 Testing ............................................................................................. 44
10.3 Partitioned Systems ......................................................................... 44
11. Alarms .......................................................................................................... 44
11.1 Burglar Alarm (Local) ....................................................................... 44
11.2 Burglar Alarm (Mercantile Safe and Vault) ...................................... 45
11.3 Burglar Alarm (Bank Safe and Vault) ............................................... 46
11.4 Burglar Alarm (Police Connect) ....................................................... 46
11.5 Burglar Alarm (Central Station) ........................................................ 46
11.6 Burglar Alarm (Proprietary) .............................................................. 46
11.7 Household Fire Alarm ...................................................................... 46
11.8 Household Burglar Alarm ................................................................. 47
Index ............................................................................................................. 49

COMPLIANCE
STATEMENTS

NGP Keypad Installation Guide
revision 1.007 — 7
1 Industry Canada Customer Information
1.1 Notices
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the equipment.
The Ringer Equivalence Number (REN) assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed five (5).
The REN for the NGP using the North American Modem is 0.1.
The REN for the NGP using the Worldwide Modem is 0.0.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any
repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines, and internal metallic water pipe system, if present, are connected together. The precaution
may be particularly important in rural areas.
1.2 Cautions
Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.

Compliance Statements
8 — revision 1.007
2 Customer Instructions Pertaining to FCC Regulations
(North America)
2.1 Notices
This equipment complies with the Federal Communications Commission (FCC) rules and regulations
governing telephone equipment and the Technical Requirements for Connection to the Telephone Network
published by the industry’s Administrative Council for Terminal Attachments (ACTA). On modem board of
this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
This equipment is designed to be connected to the telephone network or premises wiring using a hard wired
connection that does not rely on a modular jack. If a modular jack is installed, it is the responsibility of the
installing company to ensure that the jack and/or plug is compliant with the criteria of the
telecommunication industry.
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in
response to an incoming call. In most, but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total RENs, contact
the local telephone company.
The REN for the NGP using the North American Modem is 0.2.
The REN for the NGP using the Worldwide Modem is 0.0.
2.2 Cautions
If this equipment (NGP) is deemed potentially harmful to the telephone network, the telephone company
will attempt to notify you in advance of discontinuing service. If advance notice is not practical, the
telephone company will notify you as soon as possible. If service is disconnected, you will be advised of
your right to file a complaint with the Federal Communications Commission (FCC) should you believe it
necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could
affect the operation of this equipment. Should this occur, advance notice to you will be provided for you to
make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment (NGP), for repair or warranty information, please contact the
installing company.
If the equipment is causing harm to the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
There are no user serviceable parts which may be repaired by the customer. All repairs must be performed
by an authorized dealer representative.
This equipment cannot be used on public coin phone service provided by the telephone company.
Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public
service commission or corporation commission for information.)
The NGP system complies with the requirements of EN 60950, Safety of Information Technology. To
maintain compliancy, it is essential that the recommendations listed below be followed.

NGP Keypad Installation Guide
revision 1.007 — 9
2.3 Mains Supply
The NGP system is intended to be permanently connected to the A.C. power source. Ensure that a readily
accessible two-pole disconnect device (circuit breaker) is incorporated in the building installation wiring to
disconnect the equipment in case of servicing. The earth conductor to which this device is connected to shall
be clearly identified. It is important that the mains supply be connected in accordance to national electrical
wiring codes and should only be carried out by authorized persons.
The NGP control cabinets have been provided with cable knockouts on the sides, top and bottom, these are
intended for the attachment of conduit. Ensure that the mains cable entering the enclosure is securely
fastened using cable ties and that it's kept separate from all other data cables.
Some NGP models primarily intended for regions with a 230 VAC supply will come with a built-in step-
down transformer. The mains fuse used on these units is a 500 mA, 250 V fast blow. When replacing, ensure
that only the same or exact equivalent is used. Once again ensure that the mains cable is securely fastened
and kept clear of all data cables.
For those units not supplied with a built-in transformer, the NGP requires 16 VAC input at TB1 on the main
board. Use a 110 VAC to 16 VAC, minimum 40 VA step-down, energy limited Class II transformer wired
into a protected branch circuit. Only certified transformers should be used whose output is designated as
SELV. The current draw from these units should not exceed 1.8 Amps; refer to the current draw of each unit
prior to connecting to the control panel. An additional power supply will be required when the current limit
of the main panel has been reached.
2.4 Warnings (North America, Australia)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case users will be required to correct the
interference at their own expense.
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate protection measures.
3 CE Conformity
The NGP System described in this manual conforms to the requirements of the Council Directive 89/336/
EEC - The EMC Directive and 73/23/EEC - The Low Voltage Directive. 1999/5/EC-The R&TTE Directive.
To maintain compliancy with this directive, it is essential to adhere to the installation recommendations
described within this manual.

Compliance Statements
10 — revision 1.007

HARDWARE
COMPONENTS

NGP Keypad Installation Guide
revision 1.007 — 13
1 LCD Keypad Overview
The dimensions of the LCD Keypad are as follows:
• Length: 5.35 in. (13.59 cm)
• Width: 4.625 in. (11.75 cm)
• Depth: 1.0 in. (2.54 cm)
Ratings:
• LCD Keypad with Reader
- Input: 12 VDC, 110 mA
- Output: 12 VDC, 1x10 mA
• LCD Keypad
- Input: 12 VDC, 95 mA
- Output: 12 VDC, 1x10 mA
Temperature for both: -10°C to +55°C (14°F to 131°F) @ 93%
Two (2) LCD keypad versions are available:
• Standard LCD keypad (gray or white)
• LCD keypad with external reader interface (gray or white).
LCD Keypad Front (Flip Cover Closed)

Hardware Components
14 — revision 1.007
LCD Keypad Front (Flip Cover Open)
1. Yellow LED On: When trouble condition present
Flashing: When there is no AC mains
2. Green LED On: Always with power present
3. Red LED Flashing: Protection ON
Solid: Partial protection (STAY)
4. Point 3, Alert Button
(Apply the Alert Button labels as required.)5. Point 2, Alert Button
6. Point 1, Alert Button
7. Apply dealer's logo label (supplied) in the indented space at the top of the keypad.
Module Point Assignment
Module Point Description
First point: Fire Alert buttons
Second point: Panic (Hold-Up) buttons
Third point: Auxiliary Alert buttons
Points 4 – 7 Hard wire inputs (1 – 4 on the Standard version).
Points 4 – 5 Hard wire inputs (1 – 2 on the Wiegand version. All unused points are skipped.)

NGP Keypad Installation Guide
revision 1.007 — 15
Keypad Front and Back and Terminal Block Wiring
1. Keypad (front)
2. Serial # Sticker (XXXXX) Apply Serial number sticker for programming into module programming.
3. Securing Screws After placing the keypad on its back section, make sure the keypad's
securing screws (supplied) are always in!
4. Tamper Spring
5. Sonalert
6. Circuit Board Pin
Connectors
Insert circuit board pin connectors into fixed terminal blocks on inside of
keypad back. This allows the keypad to make wire connections in the
terminal blocks.
7. Keypad (back)
8. Terminal Blocks
9. Wall Tamper Knock Out See Keypad Back Cover and Wall Tamper Installation on page 17.
10. Cable

Hardware Components
16 — revision 1.007
11. Keypad Terminal Block Wiring
12. Standard
13. Module Bus
14. Module Bus
15. Wiegand
16. Point 4 - 7
17. Point 4 - 5
18. Input 1
19. Common
20. Input 2
21. Wiegand Reader Data 1 and 0. No reader LED connection.
22. Future
23. Output Keypad Output goes negative. Interface with a relay or power supply.
Common their negatives with keypad 0V.

NGP Keypad Installation Guide
revision 1.007 — 17
Keypad Back Cover and Wall Tamper Installation
1. Rectangular Conduit (Trunking)
2. Knock outs for rectangular conduit using additional keypad base.
3. To use the keypad tamper spring (see Keypad Front and Back and
Terminal Block Wiring, item 4) as a wall tamper:
a. Break out this plastic cylinder inside the back cover.
b. Screw it to the wall, keeping it in the same hole as it was
attached, so the back cover fits over it. The plastic cylinder
prevents the tamper spring from being affected by flat objects
wedged in behind the keypad. The additional keypad base is
optional. For installations using it there is a similar, shorter,
washer style, plastic break out.
c. Place it behind the plastic cylinder and screw them down
together.
d. Then, place the holes in the base and keypad backing over top of
them.
e. Fit the spring inside the plastic cylinder part and secure the
keypad front to the keypad back. The spring compressing should
reset the keypad tamper condition.

Hardware Components
18 — revision 1.007
2 LCD Keypad Notes
The LCD keypad can be connected to the NGP controller and used for programming. Please refer to the
NGP Hardware Installation Guide 55-60000E for instructions.
2.1 When a Keypad Is First Powered
When a keypad is first powered, it will display ComsLost #, for example, ComsLost 50624. The
keypad's module bus communications are not on line and the keypad's module bus, unique serial number (#)
is displayed for programming into the system. For more information, please refer to LCD Keypad on
page 31.
The left and right arrow keys in the upper right screen corner refer to the left and right arrow keypad buttons.
They can be pressed to display the following:
• The keypad version
• The module bus voltage, e.g., 13.054V
• Keypad firmware version, e.g., V0.6
2.2 Main Test Menu Selections
Using a keypad that has just been powered and not programmed into module programming, press any
number key five (5) times to display the Main Test Menu. This screen will also display the current
module bus power.
• Keypad tone volume adjustment:
Use the left and right arrow keys to indicate the various levels, visually and audibly. Press SAVE to save
the setting or RST to return the volume setting to the factory default.
• PRESS KEY
This selection allows you to press keypad keys and ensure they are working properly by seeing their
alpha/numerical value appear on the screen, hearing a keypad tone, and seeing the keypad red and
yellow lights turn on or off after each key pressed.
•CARD
This menu selection will display a card's number and if the card is ok or not when a card is held to the
keypad.
Pressing the keypad f key five (5) times for keypad serial number
After a keypad has been logged on to from the ComsLost screen using, for example, the service user's
code, e.g., 2482, or programmed into the system, or while being programmed in the Module Programming
Section, press the f keypad key five (5) times. This will cause the screen to display the type of keypad and
the keypad's serial number.

NGP Keypad Installation Guide
revision 1.007 — 19
2.3 User's Access Card Quick Enrollment
1. After a keypad has been programmed into the system, enter User Programming from the regular
keypad screens (not programming screens).
2. Proceed through the screens for assigning a user.
3. When the selection is made to assign a card for the user, hold the user's card to the keypad. The card
number will appear on screen. The card has been assigned to the user.
4. Press the escape key on the keypad to return to the main menus.
2.4 Point Mapping
• Some system expansion modules are assigned with inputs and outputs such as the 8 Point and 16 Point
Expanders.
In the Advanced Module programming section, the limits for the amounts of inputs and outputs start at
4 and 8 at a time and increase from there.
• When assigning, for example, inputs to an 8 point Expander, if the main control board has been assigned
with 12 inputs, inputs 001 to 012, the inputs on the 8 Point Expander would start at inputs 013 to 020.
This same style of point organizing continues throughout the system and is known as Point Mapping.
• Another characteristic that can occur is that not all points assigned to a module may be used.
Example: A Standard LCD keypad assigned as the first module on the module bus.
For all inputs to be used on this keypad, eight (8) inputs must be assigned. The first three (3) inputs are
assigned to the keypad's alert buttons: Fire, Police, and Auxiliary. If the main control board has inputs
001 to 012, these alert inputs will be 013 to 015. The next four (4) are assigned to the keypad's hardwire
inputs: 016 to 019. This leaves input 020, which is not used and must be skipped. The programmable
inputs for the next module assigned with eight (8) inputs after the keypad will be 021 to 028.
• This condition can also occur with outputs.
Example: An 8 Point Expander comes with outputs 1 and 2.
The 8 Point Expander does not have physical outputs 3 to 8 on the board. If more outputs are needed
with the 8 Point Expander, an output daughter card can be plugged on to the main board. The daughter
board is designed to represent outputs 9 to 16 on the Expander. This means sixteen (16) outputs need to
be assigned to the 8 Point Expander Module. Outputs 1 and 2 are programmable, 3 to 8 do not exist and
must be skipped. The daughter card's eight (8) outputs then begin programming from 9 to 16.
If a 16 Point Expander is used and all sixteen (16) outputs are needed, sixteen (16) outputs are assigned
to the module. A daughter card is again used and with this module. All sixteen (16) outputs are available
and programmable.

Hardware Components
20 — revision 1.007
3 NGP Controller
Note: Any expansion modules used with the NGP system, like the 8 Point and 16 Point Expanders,
can also be used on the NGP Main Control Unit, Module Bus (SNAPP).
3.1 Mounting a Control Box
On Dry Wall:
1. Use 1/8 in. hollow wall, expansion anchors.
2. Unscrew the screws from the anchors.
3. Hold the control box on the mounting surface.
4. Mark the mounting holes.
5. Force a starter hole in each mark with a sharp tool, e.g., a screw driver with a small, flat edge.
6. Hammer the anchors into each hole.
7. Align the box mounting holes over the anchor holes and screw in the anchor screws until tight.
On Concrete Surface:
1. Hold the control box on the mounting surface.
2. Mark the mounting holes.
3. Use a hammer drill with a 3/16 in. carballoy drill bit and make 1 in. deep holes in each marking.
4. Insert a # 6-8 plastic anchor in each hole and hammer them in.
5. Use # 8 x 1 in., Phillips, wood screws to screw into the plastic anchors and mount the box.
3.2 Control Box Dimensions
The dimensions of the control box enclosure, with the cover closed, are H 537 mm x W 343 mm x D 106
mm (H 21.14 x W 13.50 x D 4.17 inches).
Please refer to the NGP Hardware Installation Guide 55-60000E, section Enclosure, for more detailed
information.