Lenovo 21D8 Owner's manual

ThinkPad P15v Gen 3 and ThinkPad T15p Gen
3
Hardware Maintenance Manual

Third Edition (July 2023)
© Copyright Lenovo 2023.
LIMITED AND RE TRICTED RIGHT NOTICE: If data or software is delivered pursuant to a General ervices
Administration “G A” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. G -
35F-05925.

Contents
About this m nu l . . . . . . . . . . . . iii
Ch pter 1. S fety inform tion . . . . . . 1
General safety . . . . . . . . . . . . . . . . 1
Electrical safety . . . . . . . . . . . . . . . . 1
afety inspection guide. . . . . . . . . . . . . 3
Handling devices that are sensitive to electrostatic
discharge . . . . . . . . . . . . . . . . . . 3
Grounding requirements . . . . . . . . . . . . 4
afety notices (multilingual translations) . . . . . . 4
Ch pter 2. Import nt service
inform tion . . . . . . . . . . . . . . . 19
trategy for replacing FRUs . . . . . . . . . . 19
trategy for replacing a solid-state drive . . . 19
How to use error message . . . . . . . . . 20
trategy for replacing FRUs for CTO, special-bid,
and standard models. . . . . . . . . . . . . 20
Product definition . . . . . . . . . . . . 20
FRU identification . . . . . . . . . . . . 20
Ch pter 3. Gener l checkout . . . . . 21
What to do first . . . . . . . . . . . . . . . 21
Checkout guide . . . . . . . . . . . . . . . 22
Diagnosing problems . . . . . . . . . . . 22
Quick test programs . . . . . . . . . . . 23
UEFI diagnostic program . . . . . . . . . 23
Bootable diagnostic programs . . . . . . . 23
Power system checkout . . . . . . . . . . . 24
Checking the ac power adapter . . . . . . . 25
Checking the built-in battery and operational
charging . . . . . . . . . . . . . . . . 25
Checking the coin-cell battery . . . . . . . 25
Ch pter 4. Rel ted service
inform tion . . . . . . . . . . . . . . . 27
Reset or restore Windows . . . . . . . . . . . 27
Passwords. . . . . . . . . . . . . . . . . 27
Power-on password . . . . . . . . . . . 27
NVMe passwords . . . . . . . . . . . . 27
upervisor password . . . . . . . . . . . 28
ystem management password. . . . . . . 28
How to remove the power-on password . . . 29
How to remove the NVMe password . . . . . 29
How to remove the system management
password . . . . . . . . . . . . . . . 29
Power management . . . . . . . . . . . . . 30
leep mode . . . . . . . . . . . . . . 30
Hibernation mode . . . . . . . . . . . . 30
ymptom-to-FRU index . . . . . . . . . . . 31
Numeric error codes . . . . . . . . . . . 32
Error messages . . . . . . . . . . . . . 33
Beep errors. . . . . . . . . . . . . . . 33
No-beep symptoms . . . . . . . . . . . 35
LCD-related symptoms . . . . . . . . . . 35
Intermittent problems . . . . . . . . . . . 36
Undetermined problems . . . . . . . . . 36
Ch pter 5. RAID . . . . . . . . . . . . 39
torage drive requirements for RAID levels . . . . 39
Configuring RAID with the Intel R T configuration
utility (for Intel models) . . . . . . . . . . . . 39
Ch pter 6. Speci l keys . . . . . . . . 43
Ch pter 7. Loc tions . . . . . . . . . 45
Locating computer controls and connectors . . . 45
Front view . . . . . . . . . . . . . . . 45
ide view . . . . . . . . . . . . . . . 47
Rear view . . . . . . . . . . . . . . . 48
Bottom view . . . . . . . . . . . . . . 50
Locating FRUs and CRUs . . . . . . . . . . . 51
Major FRUs and CRUs . . . . . . . . . . 52
LCD FRUs . . . . . . . . . . . . . . . 54
Miscellaneous parts . . . . . . . . . . . 55
Connector and cable guide . . . . . . . . 55
Looking up FRU information . . . . . . . . . . 58
Ch pter 8. FRU repl cement
notices . . . . . . . . . . . . . . . . . 59
ervice tool kit . . . . . . . . . . . . . . . 59
crew notices . . . . . . . . . . . . . . . 59
Retaining serial numbers . . . . . . . . . . . 60
Restoring the serial number of the system
unit . . . . . . . . . . . . . . . . . . 60
Retaining the UUID. . . . . . . . . . . . 61
Reading or writing the ECA information . . . . 61
Ch pter 9. Removing or repl cing
FRU. . . . . . . . . . . . . . . . . . . 63
General guidelines. . . . . . . . . . . . . . 63
Before servicing the computer . . . . . . . . . 63
Disabling the built-in battery . . . . . . . . 63
Removing the nano- IM card and the nano-
IM-card tray . . . . . . . . . . . . . . 64
1010 Keyboard . . . . . . . . . . . . . . . 64
© Copyright Lenovo 2023 i

1020 Base cover assembly . . . . . . . . . . 66
1030 peaker assembly . . . . . . . . . . . 67
1040 Coin-cell battery . . . . . . . . . . . . 68
1050 M.2 solid-state drive . . . . . . . . . . . 68
1060 Wireless WAN card (for selected models) . . 69
1070 Memory module . . . . . . . . . . . . 70
1080 DC-IN bracket and DC-IN cable . . . . . . 71
1090 Thermal fan assembly . . . . . . . . . . 71
1100 Built-in battery . . . . . . . . . . . . . 72
1110 IO bracket. . . . . . . . . . . . . . . 73
1120 Fingerprint reader, bracket and cable . . . . 74
1130 ystem board . . . . . . . . . . . . . 75
1140 mart card reader and smart card reader
cable . . . . . . . . . . . . . . . . . . . 77
1150 LCD unit . . . . . . . . . . . . . . . 78
1160 Keyboard bezel assembly . . . . . . . . 80
2010 LCD bezel assembly . . . . . . . . . . . 81
2020 LCD panel and LCD elastic adhesive tapes . . 81
2030 Camera / mic combo board . . . . . . . . 84
2040 Camera/LED cable . . . . . . . . . . . 84
2050 LCD hinges . . . . . . . . . . . . . . 85
2060 Wireless LAN / WAN antenna assembly . . . 86
2070 LCD cover assembly. . . . . . . . . . . 87
Appendix A. Notices . . . . . . . . . . 89
Appendix B. Abbrevi tion t ble . . . . 91
ii ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

About this m nu l
This manual contains service and reference information for the following products:
Product n me M chine type (MT)
ThinkPad P15v Gen 3 21D8, 21D9, 21EM, and 21EN
ThinkPad T15p Gen 3 21DA and 21DB
ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 might be shipped with different microprocessors, namely
Intel® and Advanced Micro Devices (AMD). Hereby Intel models and AMD models are used to distinguish
computer models with different microprocessors.
Use this manual along with the advanced diagnostic tests to troubleshoot problems.
Import nt:
• This manual is intended only for trained service technicians who are familiar with products. Use this
manual along with the advanced diagnostic tests to troubleshoot problems effectively.
• Depending on the model, some hardware configuration and software programs might not be available on
the computer. ome statements in this manual might not be applicable to the computer.
• Before servicing a product, be sure to read all the information under Chapter 1 “ afety information” on
page 1 and Chapter 2 “Important service information” on page 19.
© Copyright Lenovo 2023 iii

iv ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

Ch pter 1. S fety inform tion
This chapter presents following safety information that you need to be familiar with before you service a
notebook computer.
• “General safety” on page 1
• “Electrical safety” on page 1
• “ afety inspection guide” on page 3
• “Handling devices that are sensitive to electrostatic discharge” on page 3
• “Grounding requirements” on page 4
• “ afety notices (multilingual translations)” on page 4
Gener l s fety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Ensure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, ensure that other service technicians and the customer's personnel are not
in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal
objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
Electric l s fety
Observe the following rules when working on electrical equipment.
© Copyright Lenovo 2023 1

Import nt:
• Use only approved tools and test equipment. ome hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
• Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges (E D). Do not use this type of mat to protect yourself from electrical
shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you. That person must be there
to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
CAUTION:
An electric l shock c n occur only when there is complete circuit. By observing the bove rule,
you m y prevent current from p ssing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– tand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages. Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring high
voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on:
– Power supply units
– Fans
– Units similar to those listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– witch off power.
– end another person to get medical aid.
2ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

S fety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service
technicians from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-ThinkPad / non-Lenovo features or options not covered by
this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the
beginning of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the authorized type specified for your computer. Go to: https://
support.lenovo.com/partslookup.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad / non-Lenovo alterations. Use good judgment as to the safety of
any non-ThinkPad / non-Lenovo alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered
with.
H ndling devices th t re sensitive to electrost tic disch rge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (E D). E D damage can occur when there is a difference in charge between objects.
Protect against E D damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific E D procedures when they exceed the requirements noted here.
Chapter 1.afety information 3

2. Ensure that the E D protective devices you use have been certified (I O 9000) as fully effective.
When handling E D-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling E D-sensitive devices.
• elect a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against E D damage is desirable but not necessary.
– Attach the E D ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an E D common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
S fety notices (multilingu l tr nsl tions)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• panish
• Traditional Chinese
DANGER
4ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

DANGER
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1.afety information 5

DANGER
6ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

PERIGO
PERIGO
PERIGO
Chapter 1.afety information 7

PERIGO
PERIGO
PERIGO
PERIGO
PERIGO
DANGER
DANGER
8ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1.afety information 9

DANGER
VORSICHT
VORSICHT
VORSICHT
VORSICHT
10 ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

VORSICHT
VORSICHT
VORSICHT
VORSICHT
Chapter 1.afety information 11

12 ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual

Chapter 1.afety information 13

14 ThinkPad P15v Gen 3 and ThinkPad T15p Gen 3 Hardware Maintenance Manual