Let's Go Aero H02264 User manual

Page 1 of 7
LANDING GEAR
Part No. H02264
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
4
4
1
1
4
4
4
8
8
8
16
24
4
4
1
LEG
CHANNEL
SHORT SUPPORT BAR
LONG SUPPORT BAR
NYLON SPACERS
3/8” X 1” BOLT
3/8” X 3/4” BOLT
3/8” WASHER
3/8 NUT NYLOCK
U-BOLT
1/4” NYLOCK NUT
1/4” WASHER
1/4” X 3/4IN BOLT
1/4 SHORT NYLOCK NUT
SECURITY STRAP
BLACKBOX
™
PARTS LIST
QTY. DESCRIPTION
TABLE OF CONTENTS:
BLACKBOX & SELECT GEARCAGE MODEL INSTALLATION
LANDING GEAR OPERATION
SAFE OPERATION NOTICE
2
5
7
.........................................
.............................................................................................
..................................................................................................
SECTION: PAGE NUMBER:
LG FOR BLACKBOX MANUAL 121321
7/16in Socket and Wrench
9/16in Socket & Wrench
Tools Needed
Landing Gear is an accessory option
designed for Let’s Go Aero BlackBox
and BlackBox PRO slideout cargo
carrier models.
Depending on your carrier, some
hardware will not be used and may be
discarded once installation is complete.
DO NOT
LUBRICATE LEGS
WARNING:
DO NOT EXCEED CARGO
WEIGHT LIMIT OF 300LBS
WARNING:
AB
E
K
CP
D
F G H
J
NHM
L
For More Information & Accessories,
Visit our Website - www.LetsGoAero.com
For Technical Support & Product Questions
Contact Us at 877-464-2376 or 719- 630-3800
Email: [email protected]
Mobility Aid Accessory for BlackBox & BlackBox PRO**

Page 2 of 7
BLACKBOX INSTALLATION
The following steps are intended for installation on BlackBox™ and BlackBox™ PRO models (P/N H01502 & H02196)
and GearCage® Cargo Models (P/N H00138 & H01397 ONLY)
For installation of Landing Gear on GearSpace and GearDeck Cargo Carriers refer to Page 2 of this manual.
STEP 1
STEP 2
The included Landing Gear Legs [A] are shipped in the
Nested position [Figure 1]. For assembly, the Legs must
be moved to the Deployed position [Figure 2].
For each Leg [A], pull the nested Legs outward to release
the spring loaded Engagement Tab [Figure 3].
Once released, swing to the Deployed position. [See Page
11 for more information on Landing Gear Nesting and
Deployment operation.]
Attached the one (1) Channel [B] by aligning the two (2) slots with the
holes on top of the Landing Gear Leg.
Using the hole located on the engagement side of each Landing Gear
Leg [A] fasten the Leg to the Channel using (1) 3/8” x 1” Bolt [F],
one (1) Nylon Spacer [E], one (1) 3/8” Washer [H], and one (1) 3/8”
Nylock Nut [J] per Landing Gear Leg.
NOTE: The Nylon Spacer [E] should be installed between the
Channel [B] and the Landing Gear Leg [A] as shown. [Figure 4].
On the hole located Smooth
Side of each Landing Gear Leg,
fasten the Leg to the Channel
using (1) 3/8” x 3/4” Bolt [G], one
(1) 3/8” Washer [H], and one (1)
3/8” Nylock Nut [J] per Landing
Gear Leg.
NOTE: Bolts should be
fastened in the slots so they are
positioned as far as possible
from the edge of the Channel [B]
as shown. [Figure 5]
Nested Deployed
[Figure 3]
[Figure 4]
[Figure 5]
[Figure 1]
[Figure 2]
ENGAGEMENT
TAB
TOOLS REQUIRED: 9/16IN SOCKET & WRENCH
ENGAGEMENT
SIDE
SMOOTH
SIDE
B
A
A
F
E
H
J
G
H
J
A
A
DO NOT
LUBRICATE LEGS
WARNING:

Page 3 of 7
STEP 3
STEP 4
13 inches
13 inches
21 inches 21 inches
Using two (2) U-Bolts [K], two
(2) 1/4” Washers [M], and two
(2) 1/4” Nylock Nuts [L] each,
attach two (2) Legs [A] to the
Carrier’s Frame Bars with
the wheels facing towards
the vehicle [Figure 6 & 8] by
slipping the U-Bolts between
the Frame Bars and the carrier
floor panels on the underside
of the carrier.
Legs [A] should be each
approximately 13” from the
center of the carrier.
NOTE: One (1) U-Bolt [K] will
share a slot with a 3/8” x 3/4”
Bolt [G] from STEP 2 as shown
[Figure 7].
Hand-tighten hardware only
at this time for loose fit.
In the same manor as Step 3,
attach the 3rd and 4th Leg [A]
facing away from the vehicle
to the carrier Frame Bars using
(2) U-Bolts [K], two (2) 1/4”
Washers [M], and two (2) 1/4”
Nylock Nuts [L] each [Figure 9
& 10].
These Legs [A] should be
wider set than the Legs used
in Step 3. Each approximately
21” from the center of the
carrier [Figure 11].
Hand-tighten hardware only
at this time for loose fit.
SHOWN WITHOUT CARRIER
FLOOR PANELS FOR CLARITY
SHOWN WITHOUT CARRIER
FLOOR PANELS FOR CLARITY
(REMOVING FLOOR PANELS IS NOT
NECESSARY FOR INSTALLATION)
[Figure 6] [Figure 8]
[Figure 7]
[Figure 9]
[Figure 10]
[Figure 11]
K
M
L
Frame Bar
Frame Bar
M
L
M
L
Frame Bar
TOOLS REQUIRED: 7/16IN SOCKET & WRENCH
TOOLS REQUIRED: 7/16IN SOCKET & WRENCH
B
K
A
B
A
A
A
A
K
K
K
K

Page 4 of 7
STEP 5
STEP 6
Using the Legs [A] that face away from the vehicle, remove one bolt and
associated hardware from each L eg [Figure 13].
NOTE: Remove the bolt that is located furthest away from the vehicle
on the interior of the carrier as shown [Figure 12].
Attach the Long Support Bar [D] to the Legs using one (1) 1/4
x 3/4in Bolt [N], two (2) 1/4in Washers [M], and one (1) Short
Nylock Nut [O] on
each side as shown
[Figure 14 & 15].
[Figure 15]
[Figure 13]
SHOWN WITHOUT FLOOR
PANELS FOR CLARITY
SHOWN WITHOUT CARRIER
FLOOR PANELS FOR CLARITY
[Figure 12]
A
[Figure 14]
TOOLS REQUIRED: 9/16IN SOCKET & WRENCH
TOOLS REQUIRED: 9/16IN SOCKET & WRENCH
A
D
D
N
O
M
M
A
STEP 7
Following the same
procedure as Step
9 using the Legs [A]
that face towards the
vehicle, remove two
(2) existing Leg Bolts
located closest to
the vehicle and the
associated Hardware
from each leg.
Re-attach the hardware
installing the Short
Support Bar [C] as
shown
[Figure 19 & 20].
SHOWN WITHOUT CARRIER FOR CLARITY
[Figure 17]
[Figure 16]
TOOLS REQUIRED: 9/16IN SOCKET & WRENCH, 7/16IN SOCKET & WRENCH,
LEG
HARDWARE
LEG
HARDWARE
LEG BOLT
LEG BOLT
A
A
C
C

Page 5 of 7
STEP 8
Center the each Leg assembly and then tighten and fully secure all hand-tightened hardware from Steps 3 & 4. Check all
connections before beginning Landing Gear Operation or operating the vehicle.
Always check connections and hardware before operating the tow vehicle.
WARNING:
LANDING GEAR OPERATION
The following instructions are for Landing Gear Nesting, Deployment and Extension Operations.
Starting with the narrower set of Legs [A] located closer to
the vehicle, pull each Landing Gear Leg downward until both
Engagement Tab’s release [Figure 18,19, & 20].
NESTING LEGS FOR TRANSIT- STEP 1
[Figure 20]
[Figure 18] [Figure 24]
ENGAGEMENT
TAB ENGAGED
ENGAGEMENT
TAB RELEASED
[Figure 19]
ONLY TWO LEGS
SHOWN FOR CLARITY
C
A
A
A
Swing Spring loaded Legs to nested position and
release the Engagement Tab into the notch to secure
[Figure 21 & 22].
Repeat for the wider set of legs farthest from the
vehicle.
NESTING LEGS FOR TRANSIT - STEP 2
A
[Figure 22]
[Figure 21]
ENGAGEMENT
TAB ENGAGED
ONLY TWO LEGS
SHOWN FOR CLARITY

Page 6 of 7
Never operate the vehicle unless the Landing Gear accessory is fully engaged into the Nested Engagement position.
WARNING:
Starting with the wider set of Legs [A] located
furthest from the vehicle, pull each Landing Gear Leg
parallel until each Engagement Tab releases [Figure
24, 25, & 26].
With the Engagement Tabs of both Legs [A] released,
push the Legs down until the Tabs re-engage in the
Deployed position [Figure 28, 29, 30 & 31].
Repeat Deployed Steps 1 & 2 for the thinner set of
Landing Gear Legs [A] located closest to the vehicle.
DEPLOYING FOR MOBILITY USE - STEP 1
DEPLOYMENT - STEP 2
[Figure 26]
[Figure 24]
[Figure 28]
[Figure 29]
ENGAGEMENT
TAB ENGAGED
ONLY TWO LEGS
SHOWN FOR CLARITY
ONLY TWO LEGS
SHOWN FOR CLARITY
ONLY TWO LEGS
SHOWN FOR CLARITY
[Figure 25]
ENGAGEMENT
TAB RELEASED
ENGAGEMENT
TAB RELEASED
ENGAGEMENT
TAB ENGAGED
[Figure 31]
[Figure 30]
A
A
A
NESTING LEGS FOR TRANSIT - STEP 3
Wrap the included Security Strap [P] around the Long
and Short Support Bars [C & D] and remove slack to
secure bars during transit. [Figure 23]
SHOWN WITHOUT CARRIER FOR CLARITY
[Figure 23]
C

Page 7 of 7
LEG EXTENSION: With all four Landing Gear Legs [A] in the Deployed
position, press down on the Extension Levers located on each Leg [A]
working with each bonded set in tandem to release the wheel extensions
[Figure 32].
Slide each Leg [A] downward until they reach the ground.
LEG RETRACTION: Press down and hold the Extension Levers to release
the wheel extensions [Figure 14].
Grabbing from the bottom of each wheel, push the Landing Gear Legs up
towards the carrier until desired Leg length is reached or the Legs become
fully retracted and release the extension.
EXTENSION & RETRACTION
EXTENSION
LEVER
[Figure 32]
Landing Gear wheels may be deployed on smooth & level surfaces
only. Failure to adhere to product guidelines may void warranty.
NOTICE:
A
SAFE USE OPERATION
The Landing Gear accessory’s maximum payload weight is 300 lbs (available cargo weight). Do not exceed this
carrying capacity.
Landing Gear may only be used on smooth & level surfaces.
Landing Gear weighs 40 lbs. Do not exceed the receiver hitch manufacturer’s tongue weight rating.
Do not use this accessory for purposes other than those for which they were designed. Failure to follow the guidelines of
the product’s instructions will void the warranty.
NEVER EXCEED LANDING GEAR PAYLOAD CAPACITY OR BEGIN TRANSPORT WITHOUT THE LANDING
GEAR FULLY ENGAGED IN THE NESTED POSITION. LANDING GEAR WHEEL MAY ONLY BE DEPLOYED ON
SMOOTH, LEVEL SURFACES. ALWAYS CHECK AND SECURE ALL CONNECTIONS BEFORE TRANSIT.
WARNING:
Let’s Go Aero 1 Year Limited Warranty
For information and to register on line at www.LetsGoAero.com/warranty
WARRANTY:
Copyright©2022, Lets Go Aero, Inc., All rights reserved.