LevelOne VOI-8001 User manual

1
VOI-8001
VOI-8002
VOI-8003
8-Port H.323/SIP VoIP Gateway
User Manual
Ver. 1.00-0608

2
Table of contents
CHAPTER 1. INTRODUCTION .............................................................. 3
1.1 OVERVIEW ..........................................................................................................3
1.2 PACKAGE CONTENTS...............................................................................................3
1.3 KEY FEATURE .......................................................................................................4
CHAPTER 2 GETTING STARTED ......................................................... 5
2.1 FRONT PANEL.......................................................................................................5
2.2 REAR PANEL ........................................................................................................6
CHAPTER 3 CONFIGURATION............................................................ 7
3.1 CONNECTION .......................................................................................................8
3.2 SYSTEM STATUS .................................................................................................. 10
3.3 REGISTER SERVER ............................................................................................... 11
3.4 VOIP CALL OUT.................................................................................................. 12
CHAPTER 4 WEB UI MANAGEMENT ................................................. 14
4.1 ACCESS TO WEB UI ............................................................................................. 14
4.2 WEB UI MANAGEMENT .......................................................................................... 15
4.2.1 Overview.................................................................................................. 15
4.2.3 Register Server Setting............................................................................. 54
4.2.4 Auto Provision function............................................................................. 60
4.2.5 Advance Setup ........................................................................................ 62
4.2.6 Application.............................................................................................. 74
4.2.7 System................................................................................................... 76
4.2.8 Route Function(/System Setup) ................................................................. 85
4.2.9 Backup/Restore ......................................................................................108
4.2.10 Save Modification.................................................................................111

3
Chapter 1. Introduction
1.1 Overview
The VOI-800x series VoIP Gateway is equipped with 8 standard phone ports, one
10/100BaseTX Fast Ethernet WAN port, and three 10/100BaseTX Fast Ethernet
LAN ports. With the integration of both voice and data, the offers ability to route
data information into network solution
VoIP Gateway has voice support that includes Quality of Service (QoS), voice
compression, echo cancellation, dynamic latency (jitter) buffers, silence
suppression, and comfort noise generation.
The VoIP Gateway is compatible with xDSL and Cable-modem Broadband
service providers with built-in support for DHCP Client, MAC Address Cloning,
PPPoE and multiple auto-provisioning methods.
1.2 Package Contents
- 8-Port VoIP Gateway
- CD User Manual
- Cat.5 Cable
- Power Adapter, 12VDC / 1.6A
Model No List
VOI-8001 8-Port FXS VoIP Gateway
VOI-8002 8-Port FXO VoIP Gateway
VOI-8003 4FXS+4FXO VoIP Gateway

4
1.3 Key Feature
VoIP
Support 8 simultaneous VoIP calls
Support T.38 FAX relay
Support QoS(ToS) for VoIP
Compliant with H.323 / SIP VoIP standard protocol
Extensible by external IVR/CDR/Billing servers for value- added application
Support register up to 4 Gatekeepers / Proxy servers
Support worldwide off net call by ITSP service
Support Multiple dialing plan / Call hunting group
Adaptive Jitter Buffer function
Multiple call profile for adjust VAD, Audio CODEC, H.245
tunneling, DTMF In/Out band, FAX relay, Frame Size, Q.931
Fast start parameters
VoIP Gateway
Support static and dynamic IP from DHCP, PPPoE
Built-in DHCP Server
Support TCP/UDP Port Mapping (Local Server Mapping)
Support User-definable Static Routing Table
Support Network Access Rules (LAN-to-WAN & WAN-to-LAN)
Self-Protection against DoS Attacks
Dynamic DNS Support
WAN: 10/100Mbps RJ-45 connector, auto-sensing
LAN: 3-port 10/100Mbps Ethernet Switch. (Auto MDI-II/MDI-X)
VoIP: 8 port FXO/FXS ports
LED Indicators : Power, Status, Ready, WAN linking , 3X LAN linking, Phone,
Line
Supported Protocol: UDP, TCP, Standard H.323,SIP, NAT,BOOTP, TFTP, FTP,
HTTP, TELNET, IEEE 802.3/ IEEE 802.3u
Selectable Coders: G.711, G.723.1, G.726, G.729A
DTMF / Call progress tone detection and generation
G.168 echo cancellation
1 Reset button for load factory default IP parameters setting
User friendly Web configure interface
Configuration/Upgrade Web and APS (Auto Provision Server)
Build-in watching dog for auto recovery

5
Chapter 2 Getting Started
2.1 Front Panel
VOI-8001
VOI-8002
VOI-8003
(Ready) Flash: It means when the VoIP Gateway registration fail.
(Ready) Constant: It means when the VoIP Gateway registration successes.
(Status): This LED will flash quickly when the VoIP Gateway is either
performing a self test of booting up.
(Power): The LED light on when power on.
Note:
VOI-8001 displays 1~8 Phone LED only
VOI-8002 displays 1~8 Line LED only
VOI-8003 displays 1~4 Line and 5~8 Phone LED only

6
2.2 Rear Panel
VOI-8001
VOI-8002
VOI-8003
DC12V: For the included power adapter. Be sure to use only the 12VDC/1.6A
power adapter included with the product. Using the wrong power adapter can
damage the product and void the warranty.
Reset: Clear all settings and restore them to the initial values present when
the device was purchased. After performing the reset, make sure to redefine
the IP settings for the device in the ‘Connection’.
WAN: A 10/100 dual-speed Ethernet port fitted with an RJ-45 connector
used to connect the to WAN device (usually a DSL / Cable Modem).
LAN 1~3: Three of 10/100 dual-speed Ethernet port fitted with an RJ-45
connector used to connect the VoIP Gateway to a LAN device.
Phone [P]: Normal RJ-11 phone jacks used to connect analog telephones
and fax machines.
Line [L]: Normal RJ-11 phone jacks used to connect analog phone line or
PSTN (landline)
Note:
Do not place heavy objects on the VoIP Gateway. Placing the VoIP Gateway in a well ventilated
area is very important. Not doing so may cause damage to the unit.

7
Chapter 3 Configuration
The default setting of DHCP Server inside VoIP Gateway is turn ON, So please set up
your PC TCP/IP network as “Get IP Automatically” from DHCP to get internal IP from
VoIP Gateway. By default, The VoIP Gateway will become the network gateway and
default IP is 192.168.22.1 and will assign your PC IP as 192.168.22.X.
Please go to “Control Panel”→”Network”. In the “Configure” page, choose the TCP/IP of
LAN card, and press “Properties” please choose “Obtain IP Address Automatically”
Launch your browser and open the Internal UI WAP page as 22http://192.168.22.1
The default User name is voip
The default Password is 1234

8
3.1 Connection
Click “Connected Type” option below “System Setup\Wan” item:
To use Static-IP ADSL connection, please select “Static IP Address” and enter
WAN IP settings.
Please select the type of Internet connection you have
and set up the VoIP Gateway to use the Dynamic IP
Address, Static IPAddress, PPPoE, PPTP or L2TP
connection.
If your ISP has not given you an IP address, select
Dynamic IP Address (default). If you have been given
a specific IP address, select Specify an IP Address.

9
To use PPPoE ADSL connection, please select Yes in use “PPPoE” ADSL
service and enter the “username” and “password” in the PPPoE setup
section. Most of ADSL ISPs assign dynamic-IP settings to the VoIP Gateway
when using PPPoE. Please select Obtain IP Address Automatically(default
setting). You can leave the Primary and Secondary DNS IP settings in default.
The VoIP Gateway automatically obtains these settings from your ISP when
the PPPoE connection is successfully established.
Please remember to setting the Primary and Secondary DNS IPs, supplied
by your ISP

10
3.2 System status
This page reveals the status of the VoIP Gateway including WAN, LAN and some
hardware/firmware information.

11
3.3 Register Server
If this VoIP Gateway wants to use SIP Proxy or GateKeeper service to transfer
the VoIP call, you can input the server information here. The VoIP Gateway can
register to up to four servers simultaneously.
This page reveals the status of the server registration information.
Here is the server configuration page, please ask the information form your
ITSP.
Remark: For Notify remark for this rule. Please use UNDERLINE to
replace the SPACE due to HTTP protocol limitation.

12
3.4 VoIP Call Out
User key in the phone number through phone set dial pad, then VoIP Gateway
translate the phone number by the routing table setting here to destination IP & dial
out number then Call out via network protocol
Remark: For Notify remark for this rule. Please use UNDERLINE to
replace the SPACE due to HTTP protocol limitation.
Area Code: Define the Prefix number fit this rule, any phone number
prefix digits matched with the rule will call out by this rule define. Please
Notify there is a compare order rule on this routing table. That mean the
VoIP Gateway will check the rule list from top to bottom one by one, any rule
item matched with the prefix digits that user key in will go to call out directly
no regard to the rest rules below. For Example, if a rule item for area code
8862 is on Index 5, another rule item for area code 886 on Index 6 below
that will be ignored.
Min Digits: The length of the dialed number should not less than this
digits. For example, if the field is entered into ‘3’, the length of the dial
number should be 3 digits at least.
Max Digits: The length of the dialed number should not more than this
digits. For example, if the field is entered into ‘10’, the length of the dial
number should be 3 digits at most.
a. IP Address: Define the destination IP for call out number fit this rule, user
can input below format:

13
IP address, for example: 168.56.9.22
URL, route via URL. For example: www.freeworlddialip.com .This VoIP
Gateway can setup to register to DDNS service (/System Setup
/Advanced/ Dynamic DNS/)to let user call out to another VoIP
Gateway with dynamic IP by URL.
rsn , route via server, it will get the destination IP by server setting
(/VoIP Setup/Register server/) in advance. For example: rs1 for
server 1. rs2 for server 2. rs for all the server available ( search
sequence: rs1 > rs2 > rs3 > rs4). rs3_2_1 will try rs3 first, then rs2,
then rs1.
IP address, for example: 168.56.9.22
All the setting above can be added by port number, for examples:
168.56.9.22:8495 will call to 8495 port.
Strip: the number of digits will be ignored by user input. For example, if
user key in the number is 886212345678 and the STRIPE field is setting to
4, the first 4 digits 8862 will be truncated and actually call out number will
be 12345678.
Prefix: The numbers will be added on the prefix of user key in number.
For examples, if user key in the number is 12345678 and the PREFIX field is
setting to 0028862, the actually call out number will be 002886212345678.
Another example, if user key in the number is 90, STRIP field is setting to 2,
and the PREFIX field is setting to 0,12345678, the actually call out number
will be 0,12345678 ( , mean wait 1 second). This example is especially for
speed dial function.
To add new rule item on routing table, please assign the item number you want to
insert before, input AREA CODE and IP address then press ADD button to add it on
the list. Then modify the necessary information on the routing table list.
Please remember to press the modify button to take it effect. For store back to flash
memory, please press “Save Modification”.

14
Chapter 4 Web UI Management
4.1 Access to Web UI
The VoIP Gateway provide user friendly Web interface to let you configure your VoIP
Gateway function
The default setting of DHCP Server inside VoIP Gateway is turn ON, So please set up
your PC TCP/IP network as “Get IP Automatically” from DHCP to get internal IP from
VoIP Gateway. By default, The VoIP Gateway will become the network gateway and
default IP is 192.168.22.1 and will assign your PC IP as 192.168.22.X.
Please go to “Control Panel”→”Network”. In the “Configure” page, choose the TCP/IP of
LAN card, and press “Properties” please choose “Obtain IP Address Automatically”
Launch your browser and open the VoIP Gateway Internal UI WAP page as
http://192.168.22.1
The default User name is voip
The default Password is 1234

15
4.2 Web UI Management
The VoIP Gateway provide user friendly Web interface to let you configure your VoIP
Gateway function and VoIP function. There are a help on line content within each
setting page. Please press Help hyperlink to view the on line help. There are 3 main
functions for web, VoIP, System Setup (VoIP Gateway) & System maintenance. Each
function is setup by the function below:
4.2.1 Overview
Route function
zConnection (Setting WAN connecting)
zLAN Setting
zFirewall Basic setup
zNetworks System Status Display
zDynamic DNS Setting
zDHCP Server Setting
zStatic Routing Setting
zLocal Server Setting
zDMZ Setting
VoIP function
zPort Status Display
zLine Configure Setting
zLine Setting
zTone Setting
zVoIP Call Out Routing Table Setting
zVoIP Call In Routing Table Setting
zVoIP Call In IVR
zVoIP Routing Profile Setting
zVoIP Forwarding Profile Setting
zAuthorization
zRegister Status

16
System Maintenance function
zConfigurations Backup/Restore
zVoIP Module Backup/Restore
zReboot System
zSave Modification
Gateway Manual overview

17
4.2.2 VoIP Function
4.4.2.1 VoIP Setup/ Port Status/
This page will display the current and last time VoIP call status & result.
a. The PC time : will show the date & time that your connected PC now.
b. The VoIP Gateway time : will show the date & time on this VoIP Gateway,
the date& time may get from SNTP server or setting from your PC. You may
set the SNTP server from /System Setup/Administrator/Date & Time/.
A. Ports Message
a. Port: display the port number, e.g. 1 or 2.
b. Type: Telephone interface type:
FXO: (DAA interface) for connect to telephone line or PBX extension
line.
FXS: (SLIC interface) for connect to regulate phone set.
c. Display Name: display the remote party name of this VoIP call.
d. Status: Current status of this port.
Idle: Standby for make a phone call.
Signal: Waiting for DTMF press or VoIP protocol connecting.
In: There is a phone call made from phone port and call out to Network
by VoIP.

18
Out: There is a phone call made from Network VoIP and pick up by
phone set.
e. Connected IP: The remotely party IP of this VoIP call.
f. Caller ID: Caller ID received from telephone line port.
g. Start Time: Date & time of this VoIP call begin on this port.
h. End Time: Date & Time of last VoIP call End on this port.
i. Talking Sec: Total talked seconds of last VoIP call on this port.
j. Dialed number:
On the VoIP call out (line status display “In”). This will display the real
dial out number for VoIP call.
On the VoIP call in (line status display “Out”). This will display the
number will dial out to phone line.
Release by: This will display the reason of this call termination.
B.Error Message
For some reason,(ex. All lines of this VoIP Gateway are busy) here will display
the failure information about the last failure VoIP Call.

19
4.2.2.2 VoIP/Line Configure/ Line Setting
/VoIP Setup/Line Configure/Line Setting/
This page will setup the phone line information each port.
a. Port: display the port number, e.g. 1 or 2.
b. Interface: Telephone interface type:
FXO: for connect to telephone line or PBX extension line.
FXS: for connect to regulate phone set
a. Name: Line name for this port. This will send and display on the remote
side during VoIP call
b. Line number: Telephone number assigned to this line.
c. TxGain: Transmitter Gain. This will adjust the speaker volume of local
phone set. The adjust range is from +3 to -13dB. Higher value will cause
louder sound come from local phone set.
d. RxGain: Receiver Gain. This will adjust the microphone volume of local
phone set. The adjust range is from -3 to +13dB. Higher value will increase
amplifier the sound get from local phone set.
e. Inbound: Enable or disable the VoIP call to Internet. Disable the inbound
option will not allow any call made from phone set to Internet.
f. Outbound: Enable or disable the VoIP call from Internet. Disable the
Outbound option will not allow any call made from Internet to phone set.
g. Hotline: When Enable, it will allow you to make a VoIP call without Press
any number. That mean it will direct call out by VoIP when you off hook the
phone of this line.
For example, if you want line 1 to become a hot line for VoIP call, every time

20
when you off hook the phone connected to the line 1, it will directly call to
another VoIP gateway location at 168.56.09.22 and dial 601. You can enable the
line 1 as hot line, and add a routing rule on the routing table on /VoIP
Setup/Routing Setup/VoIP Call Out/ to assign the AREA CODE to hl1 to
handle the VoIP Gateway rule for hot line function. And please also remember to
Strip 3 digits to stripe the “hl1” symbol and remember add real phone number
you want to dial on Prefix. In this case, the setting example on call out routing
(/VoIP Setup/Routing Setup/VoIP Call Out/) for hot line application is as
below:
Index Remark Area Code IP Address Strip Prefix Profile Delete
1 Hot_Line_Call Hl1 10.1.1.1 3 601 22Delete