LevelOne FBR-1161 User manual

FBR-1161
ADSL2+ Modem Router
1WAN 1LAN 1USB
User Manual
V1.0

ii
Table of Content
1. INTRODUCTION....................................................................................................................................... 1
1.1. OVERVIEW ......................................................................................................................................... 1
1.2. FEATURES.......................................................................................................................................... 3
2. INSTALLATION ........................................................................................................................................ 6
2.1. IMPORTANT NOTE ............................................................................................................................... 6
2.2. PACKAGE CONTENTS.......................................................................................................................... 6
2.3. FRONT PANEL..................................................................................................................................... 7
2.4. REAR PANEL....................................................................................................................................... 8
2.5. CABLING ............................................................................................................................................ 9
3. BASIC INSTALLATION.......................................................................................................................... 10
3.1. BEFORE CONFIGURATION.................................................................................................................. 10
3.2. FACTORY DEFAULT SETTINGS............................................................................................................ 10
3.3. INSTALLING THE USB DRIVER.............................................................................................................11
3.3.1. For Windows XP & 2000.............................................................................................................11
3.3.2. For Windows 98SE & Me........................................................................................................... 14
3.4. CONFIGURING YOUR PC NETWORK PROPERTIES............................................................................... 16
3.4.1. Windows XP............................................................................................................................... 16
3.4.2. Windows 2000............................................................................................................................ 17
3.4.3. Windows 98SE/Me..................................................................................................................... 18
3.4.4. Configuring PC in Windows NT4.0 ............................................................................................ 19
3.5. LANAND WAN PORT ADDRESSES .................................................................................................... 20
3.6. ISPINFORMATION............................................................................................................................. 20
3.7. CONFIGURING WITH YOUR WEB BROWSER......................................................................................... 21
4. CONFIGURATION.................................................................................................................................. 22
4.1. QUICK START ................................................................................................................................... 22
4.2. INTERFACE SETUP ............................................................................................................................ 25
4.2.1. Internet....................................................................................................................................... 25
4.2.2. LAN............................................................................................................................................ 31
4.3. ADVANCED SETUP ............................................................................................................................ 33
4.3.1. Firewall....................................................................................................................................... 33
4.3.2. Routing....................................................................................................................................... 33
4.3.3. NAT ............................................................................................................................................ 35
4.3.4. ADSL.......................................................................................................................................... 40
4.4. ACCESS MANAGEMENT..................................................................................................................... 41
4.4.1. ACL............................................................................................................................................ 41

iii
4.4.2. IP Filter....................................................................................................................................... 42
4.4.3. SNMP......................................................................................................................................... 44
4.4.4. UPnP.......................................................................................................................................... 45
4.4.5. DDNS......................................................................................................................................... 46
4.5. MAINTENANCE.................................................................................................................................. 47
4.5.1. Administrator.............................................................................................................................. 47
4.5.2. Time Zone.................................................................................................................................. 48
4.5.3. Firmware.................................................................................................................................... 49
4.5.4. SysRestart.................................................................................................................................. 50
4.5.5. Diagnostics................................................................................................................................. 50
4.6. STATUS ............................................................................................................................................ 51
4.6.1. Device Info................................................................................................................................. 51
4.6.2. System Log................................................................................................................................ 53
4.6.3. Statistics..................................................................................................................................... 54
5. TROUBLESHOOTING ........................................................................................................................... 56

1
1. Introduction
1.1. Overview
Welcome to the LevelOne FBR-1161. Your router is an “all-in-one” unit, combining an ADSL
modem, ADSLrouter and Ethernet network switch, providing everything you need to get the
machines on your network connected to the Internet over yourADSLbroadband connection.
The FBR-1161 complies with ADSL2+ standards for worldwide deployment and supports
downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It is designed for
small office, home office and residential users, enabling even faster speed Internet
connections. User can enjoy ADSLservices and broadband multimedia applications such as
interactive gaming, video streaming and real-time audio much easier and faster than ever
before.
The product supports PPPoA (RFC 2364 –PPP (Point-to-Point Protocol) over ATM
Adaptation Layer 5), RFC 1483 encapsulation overATM (bridged or routed), PPP over
Ethernet (RFC 2516), and IPoA (RFC1577) to establish a connection with ISP. The product
also supports VC-based and LLC-based multiplexing.
It is the perfect solution to connect a small group of PCs to a high-speed broadband Internet
connection. Multi-users can have high-speed Internet access simultaneously.
This product also serves as an Internet firewall, protecting your network from being
accessed by outside users. Not only provide the natural firewall function (NetworkAddress
Translation, NAT), it also provides rich firewall features to secure user’s network. All
incoming data packets are monitored and filtered. Besides, it can also be configured to
block internal users from accessing to the Internet.
The product provides two levels of security support. First, it masks LAN users’ IP addresses
which are invisible to outside users on the Internet, making it muchmore difficult for a hacker
to target a machine on your network. Secondly, it can block and redirect certain ports to limit
the services that outside users can access. For example, to ensure that games and other
Internet applications will run properly, user can open some specific ports for outside users to
access internal services in network.
Integrated DHCP (Dynamic Host Control Protocol) services, client and server, allow multiple
users to get their IP addresses automatically on boot up from the product. Simply set local

2
machines as a DHCP client to accept a dynamically assigned IP address from DHCP server
and reboot. Each time local machine is powered up; the router will recognize it and assign
an IP address to instantly connect it to the LAN.
For advanced users, Virtual Service function allows the product to provide limited visibility to
local machines with specific services for outside users. An ISP (Internet Service Providers)
provided IP address can be set to the product and then specific services can be rerouted to
specific computers on the local network. For instance, a dedicated web server can be
connected to the Internet via the product and then incoming requests for HTML that are
received by the product can be rerouted to the dedicated local web server, even though the
server now has a different IP address. In this example, the product is on the Internet and
vulnerable to attacks, but the server is protected.
Virtual Server can also be used to re-task services to multiple servers. For instance, the
product can be set to allow separated FTP, Web, and Multiplayer game servers to share the
same Internet-visible IP address while still protecting the servers and LAN users from
hackers.

3
1.2. Features
ADSL Multi-Mode Standard
supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It
also supports rate management that allowsADSL subscribers to select an Internet
access speed suiting their needs and budgets. It is compliant with Multi-Mode standard
(ANSI T1.413, Issue 2; G.dmt(G.992.1); G.lite(G992.2)), G.hs (G994.1), G.dmt.bis
(G.992.3), G.dmt.bisplus (G.992.5)). The AnnexA and B are supported in different H/W
platforms.
Fast Ethernet Switch
A 10/100Mbps fast Ethernet switch is built in with automatic switching between MDI
and MDI-X for 10Base-T and 100Base-TX ports.An Ethernet straight or cross-over
cable can be used directly for auto detection.
Multi-Protocol to Establish A Connection
Supports PPPoA(RFC 2364 - PPP overATM Adaptation Layer 5), RFC 1483
encapsulation overATM (bridged or routed), PPP over Ethernet (RFC 2516) and IPoA
(RFC1577) to establish a connection with the ISP. The product also supportsVC-based
and LLC-based multiplexing.
Quick Installation Wizard
Supports aWEB GUI page to install this device quickly. With this wizard, end users can
enter the information easily which they get from their ISP, then surf the Internet
immediately.
Universal Plug and Play (UPnP) and UPnP NAT Traversal
This protocol is used to enable simple and robust connectivity among stand-alone
devices and PCs from many different vendors. It makes network simple and affordable
for users. UPnP architecture leverages TCP/IP and the Web to enable seamless
proximity networking in addition to control and data transfer among networked devices.
With this feature enabled, users can now connect to Net meeting or MSN Messenger
seamlessly.
Network Address Translation (NAT)
Allows multi-users to access outside resources such as the Internet simultaneously
with one IP address/one Internet access account. Many application layer gateway
(ALG) are supported such as web browser, ICQ, FTP, Telnet,E-mail, News, Net2phone,
Ping, NetMeeting, IP phone and others.
Firewall
Supports simple firewall with NAT technology and provides option for blocking access
from Internet, like Telnet, FTP, TFTP, WEB, SNMP and IGMP.
Domain Name System (DNS) relay
Provides an easy way to map the domain name (a friendly name for users such as

4
www.yahoo.com) and IP address. When a local machine sets its DNS server with this
router’s IP address, every DNS conversion request packet from the PC to this router
will be forwarded to the real DNS in the outside network.
Dynamic Domain Name System (DDNS)
The Dynamic DNS service allows you to alias a dynamic IP address to a static
hostname. This dynamic IP address is the WAN IP address. For example, to use the
service, you must first apply for an account from a DDNS service like
http://www.dyndns.org/.
PPP over Ethernet (PPPoE):
Provides embedded PPPoE client function to establish a connection. Users can get
greater access speed without changing the operation concept, sharing the same ISP
account and paying for one access account. No PPPoE client software is required for
local computer. The Automatic Reconnect and Disconnect Timeout (Idle Timer)
functions are provided, too.
Virtual Server
User can specify some services to be visible from outside users. The router can detect
incoming service request and forward it to the specific local computer to handle it. For
example, user can assign a PC in LAN acting as WEB server inside and expose it to
the outside network. Outside user can browse inside web server directly while it is
protected by NAT. A DMZ host setting is also provided to a local computer exposed to
the outside network, Internet.
Users can specify some services to be visible from outside users. The router can detect
incoming service requests and forward either a single port or a range of ports to the
specific local computer to handle it. For example, a user can assign a PC in the LAN
acting as a WEB server inside and expose it to the outside network. Outside users can
browse inside web servers directly while it is protected by NAT.A DMZ host setting is
also provided to a local computer exposed to the outside network, Internet.
Dynamic Host Configuration Protocol (DHCP) client and server
In the WAN site, the DHCP client can get an IP address from the Internet Service
Provider (ISP) automatically. In the LAN site, the DHCP server can allocate a range of
client IP addresses and distribute them including IP address, subnet mask as well as
DNS IP address to local computers. It provides an easy way to manage the local IP
network.
RIP1/2 Routing
Supports RIP1/2 routing protocol for routing capability.
Simple Network Management Protocol (SNMP)
It is an easy way to remotely manage the router via SNMP.
Web based GUI

5
Supports web based GUI for configuration and management. It is user-friendly and
comes with on-line help. It also supports remote management capability for remote
users to configure and manage this product.
Firmware Upgradeable
Device can be upgraded to the latest firmware through the WEB based GUI.

6
2. Installation
2.1. Important Note
Warning:
Do not use the FBR-1161 in high humidity or high temperatures.
Do not use the same power source for the FBR-1161 as other equipment.
Do not open or repair the case yourself. If the FBR-1161 is too hot, turn off the power immediately and
have it repaired at a qualified service center.
Avoid using this product and all accessories outdoors.
Attention:
Place the FBR-1161 on a stable surface.
Only use the power adapter that comes with the package. Using a different voltage rating power adaptor
may damage the router.
2.2. Package Contents
FBR-1161 ADSL2+ Modem/Router
AC-AC Power Adapter (12V AC, 1A)
Quick Installation Guide
CD-ROM containing the User Manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
USB Cable (1.5M)

7
2.3. Front Panel
LED
Description
PPP
Lit steady when there is a PPPoA/ PPPoE connection.
ADSL
Lit when successfully connected to an ADSL DSLAM (“linesync”)
USB
Lit when the USB port is connected to the PC and working properly
LAN
Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
SYS
Lit when the system is ready.
PWR
Lit when power is ON.

8
2.4. Rear Panel
Port
Description
Switch
Power ON/OFF switch
POWER
Connect the supplied power adapter to this jack.
RESET
After the device is powered on, press it to reset the device or restore to
factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this is used when
you can not login to the router, e.g. forgot the password)
LAN
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to the LAN ports
when connecting to a PC or an office/home network of 10Mbps or
100Mbps.
USB
Connect the supplied USB cable to this port when connecting to the
PC
ADSL
Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
RESET
LAN
USB
ADSL
Power
Switch

9
2.5. Cabling
Through USB Port
The product can be used as a Network Adapter on your PC. That means you do not have to
install a network adapter first on your PC before connecting the ADSL Modem/Router. Just
connect the supplied USB cable to the USB port of the ADSL2+ Modem/Router and connect
the other end to the PC.
Make sure that yourADSL Modem/Router and PC are turned on. On the front of the product
is a bank of LEDs. As a first check, please verify that the PWR, SYS, USB and ADSL LEDs
are lit. So long as the cables are connected and the LEDs are lit normally, follow section
“Installing the USB Driver” below to setup this device.
Through Ethernet Port
The product’s LAN port is wired just like a Network Adapter’s port. From the product directly
to a PC, the cable should be an Ethernet crossover cable. From the product to a hub or
switch, the cable should be an Ethernet straight through cable to a normal hub/switch port,
or an Ethernet crossover cable to an uplink port.
The most common problem associated with Ethernet is bad cabling or ADSLline. Make sure
that all connected devices are turned on. On the front of the product is a bank of LEDs. As a
first check, please verify that the PWR, LAN LNK and ADSLSYN LEDs are lit. If they are not,
verify that you are using the proper cables.
So long as the cables are connected and the LEDs are lit normally, follow section
“Configuring the Network Properties” below to modify the network settings.
Attention:
Since the product cannot auto-detect whether your cable is correct or not, please make sure you are
using the right cable to a PC or a Hub.

10
3. Basic Installation
The router can be configured with your web browser. A web browser is included as a
standard application in the following operating systems: Windows 98SE/Me/NT/2000/XP,
etc. The product provides a very easy and user-friendly interface for configuration.
3.1. Before Configuration
PCs must have an Ethernet interface installedproperly and be connected to the router either
directly or through an external repeater hub, and have TCP/IP installed and configured to
obtain an IP address through a DHCP server or a fixed IP address that must be in the same
subnet as the router. The best and easiest way is to configure the PC to get an IP address
automatically from the router using DHCP. If you encounter any problems accessing the
router’s web interface it may also be advisable to uninstall any kind of software firewall on
your PCs, as they can cause problems accessing the 192.168.1.254 IP address of the
router.
Note:
Any TCP/IP capable workstation can be used to communicate with or through the ADSL2+
Modem/Router. To configure other types of workstations, please consult the manufacturer’s
documentation.
3.2. Factory Default Settings
Web Interface:
Username: admin
Password: admin
LAN Device IP Settings:
IPAddress: 192.168.1.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site:
PPPoE
DHCP server:
DHCP server is enabled.
Start IPAddress: 192.168.1.100
IP pool counts: 100
Attention:
If you ever forget the password to log in, you may press the RESET button up to 6 seconds to restore the
factory default settings.

11
3.3. Installing the USB Driver
If you connect the device through USB port instead of Ethernet port, for the first time the
USB cable is connected to the PC, Windows will automatically detect the device. Follow the
steps to install the USB driver.
3.3.1. For Windows XP & 2000
Start Windows. Then insert the installation
CD into the CD-ROM drive. In next window,
to specify the CD ROM driver directory and
to continue.
To choose the setup language. ”and click
“Next >”. (There are three languages that
user can choose: English. German and
French)

12
Then follow screen.
To click the type of setup you prefer, then
click Next >.
To setup enough information of coping the
program files then click Next >.

13
Please plug USB cable into ADSL USB
Modem.
Then, click “Finish”.

14
3.3.2. For Windows 98SE & Me
Start Windows. Then insert the installation
CD into the CD-ROM drive. In next window,
to specify the CD ROM driver directory and
to continue.
To choose the setup language. ”and click
“Next >”. (There are three languages that
user can choose: English. German and
French)
Then follow screen.

15
To click the type of setup you prefer, then
click Next >.
To setup enough information of coping the
program files.
Select “Want to restart my computer now”
and click OK>
Then, click “Finish”.

16
3.4. Configuring Your PC Network Properties
3.4.1. Windows XP
Go to Start / Control Panel (in Classic View).
In the Control Panel, double-click on
Network Connections
Double-click Local Area Connection.
In the Local Area Connection Status
window, click Properties.
Select Internet Protocol (TCP/IP) and click
Properties.
Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
Click OK to finish the configuration.

17
3.4.2. Windows 2000
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on
Network and Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and
click Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.