LevelOne IFE-0501 User manual

LevelOne
IFE-0501/IFE-0502
4-Port PoE + 1-Port SC
Industrial Fast Ethernet Switch
User Manual
Ver. 1.0.0-0711
1

FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. It may
cause harmful interference to radio communications if the equipment is not installed
and used in accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
2

Content
INTRODUCTION......................................................................................4
FEATURES................................................................................................................. 4
PACKAGE CONTENTS ................................................................................................. 5
HARDWARE DESCRIPTION...................................................................6
PHYSICAL DIMENSION ................................................................................................ 6
FRONT PANEL ........................................................................................................... 6
TOP VIEW ................................................................................................................. 7
LED INDICATORS....................................................................................................... 8
PORTS...................................................................................................................... 9
CABLING ..................................................................................................................11
WIRING THE POWER INPUTS ..................................................................................... 12
WIRING THE FAULT ALARM CONTACT ......................................................................... 13
MOUNTING INSTALLATION.................................................................14
DIN-RAIL MOUNTING ............................................................................................... 14
WALL MOUNT PLATE MOUNTING ............................................................................... 16
HARDWARE INSTALLATION ...............................................................17
INSTALLATION STEPS ............................................................................................... 17
NETWORK APPLICATION....................................................................18
TROUBLESHOOTING...........................................................................19
TECHNICAL SPECIFICATION ..............................................................20
3

Introduction
The 4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch is a cost-effective solution
and meets the high reliability requirements demanded by industrial applications. Using
fiber port can extend the connection distance that increases the network elasticity and
performance. In addition, the industrial switch provides the PoE function for kinds of
Powered Devices to receive power as well as data over the RJ-45 cable.
Features
System Interface/Performance
yRJ-45 ports support Auto MDI/MDI-X Function
yEmbedded 4-port PoE Injection
yStore-and-Forward Switching Architecture
yBack-plane (Switching Fabric): 1.0Gbps
y1K MAC Address Table
yFiber cable up to 2km by Full-duplex Multi-mode(IFE-0501)
yFiber cable up to 30km by Full-duplex Single-mode(IFE-0502)
Power Supply
yDC 48V Redundant Power (Full load with PoE)
yOverload Current Re-settable Fuse Present
Case/Installation
yIP-30 Protection
yDIN Rail and Wall Mount Design
Provides EFT protection 3,000 VDC for power line
Supports 4,000 VDC Ethernet ESD protection
4

Package Contents
Please refer to the package contents list below to verify them against the checklist.
IFE-0501(or IFE-0502)
CD Manual
Pluggable Terminal Block (attached on the switch)
2 wall mount plates with screws
One DIN-Rail (attached on the switch)
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.
5

Hardware Description
In this paragraph, the Industrial switch’s hardware spec, port, cabling information, and
wiring installation will be described.
Physical Dimension
4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch dimension (W x D x H) is
30mm x 95mm x 140mm
Front Panel
The Front Panel of the 4-Port PoE + 1-Port Multi-mode SC Industrial Fast Ethernet
Switch is shown as below:
Front Panel of the IFE-0501 Industrial Fast Ethernet Switch
6

The Front Panel of the 4-Port PoE + 1-Port Single-mode SC Industrial Fast Ethernet
Switch is shown as below:
Front Panel of the IFE-0502 Industrial Fast Ethernet Switch
Top View
The top view of the 4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch has one
terminal block connector of two DC power inputs.
Top View of the IFE-0501/IFE-0502 Industrial Fast Ethernet Switch
7

LED Indicators
The diagnostic LEDs located on the front panel of the industrial switch provide
real-time information of system and optional status. The following table provides the
description of the LED status and their meanings for the switch.
LED Color Description
On Power input 1 is active
P1 Green
Off Power input 1 is inactive
On Power input 2 is active
P2 Green
Off Power input 2 is inactive
On Power input 1 or 2 has failed
Fault Red Off Power input 1 and 2 are both functional,
or no power inputs
On The port is supplying power to the
powered-deviceFWD
(1 ~ 4) Green
Off No powered-device attached or power
supplying fails
On Connected to network
Flashing Networking is active
5 LNK/ACT
(fiber port) Green
Off Not connected to network
On Connected to network
Flashing Networking is active
Green
(Upper LED) Off Not connected to network
On Full-duplex link
Flashing Collision occurs
1 ~ 4
(RJ-45) Yellow
(Lower LED) Off Half-duplex link or link down
8

Ports
RJ-45 ports
The UTP (RJ-45) Fast Ethernet ports will auto-sense for 10Base-T or 100Base-TX
connections. Auto MDI/MDIX means that the switch can connect to another switch or
workstation without changing straight through or crossover cabling. See the below
figures for straight through and crossover cable schematic.
RJ-45 Pin Assignments
Pin Number Assignment
1 Tx+
2 Tx-
3 Rx+
6 Rx-
“+” and “-” signs represent the polarity of the wires that make up
each wire pair.
All ports on this industrial switch support automatic MDI/MDI-X operation, user can
use straight-through cables (See figure below) for all network connections to PCs or
servers, or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at
one end of the cable, are connected straight through to pins 1, 2, 3 and 6 at the other
end of the cable. The table below shows the 10BASE-T/100BASE-TX MDI and MDI-X
port pin outs.
Pin MDI-X Signal Name MDI Signal Name
1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)
9

Straight Through Cable Schematic
Cross Over Cable Schematic
Fiber Port
The fiber port of SC type connector can work in multi-mode (2Km) or single-mode
(30Km). When you connect the fiber port to another one, please follow the figure
below to connect accordingly. Wrong connection will cause the port cannot work
normally.
ATTENTION
This is a Class 1 Laser/LED product.
Don’t stare into the Laser/LED Beam.
10