LevelOne FSW-0511 User manual

LevelOne
User Manual
FSW-0511 / FSW-0811
5/8-Port Fast Ethernet Switch
V1.0.0-0803

2
FCC Certifications
This Equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE Marking Warning
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 Class B for ITE, the essential protection
requirement of Council Directive 89/336/EEC on the approximation of the
laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent
from the company.

3
Package Contents
•FSW-0511 or FSW-0811
•Power Adapter
•User Manual
•Wall-Mounting Kit
Installation
1. Please inspect the Power Adapter carefully, and make
sure that it is properly connected to a power source.
2. Power on. It will be automatically initialized and the LED
indicators should respond as follows:
a. All of the Link/Act LED indicators will flash
momentarily, which represent a resetting of the
system.
b. The Power LED indicators will light up.

4
Features & Specifications
y5/8 auto-negotiation 10/100 Mbps Ethernet ports
yAuto MDI/MDI-X at each port
ySupports IEEE802.3x flow control for Full Duplex mode and
backpressure for Half Duplex mode
yData filtering and forwarding at full wire speed
yStore-and-Forward switching technology
Standards IEEE802.3 10Base-T, IEEE802.3u 100Base-TX
Data Transfer
Rate 10Mbps (Half Duplex), 20Mbps (Full Duplex)
100Mbps (Half Duplex), 200Mbps (Full Duplex)
Network
Media
(Cable)
10BASE-T: UTP category 3, 4, 5 cable (maximum
100m) EIA/TIA-568 STP (maximum 100m)
100BASE-Tx: UTP category 5, 5e cable (maximum
100m) EIA/TIA-568 STP (maximum 100m)
Interface 5/8 10/100MbpsAuto-Negotiation ports
Power
Supply FSW-0511 AC 12V~ 0.35A/ DC 12V 0.35A
FSW-0811 AC 9V~ 0.8A/ DC 12V 1A
Temperature Operating Temperature: 0℃~40℃
Storage Temperature: -10℃~70℃
Humidity Operating Humidity: 10%~90% non-condensing
Storage humidity: 5%~95% non-condensing

5
LED Definition
FSW-0511/FSW-0811 Front Panel
PWR This indicator will light up when the Switch powers up
Link/Act One LED indicator will light green when a device is
connected to the corresponding port. It flashes when
data is being transmitted or received on the connection.
Rear Panel
The rear panel of the FSW-0511/FSW-0811 consists of 5/8
10/100Mbps RJ45 Ports. All ports can work as the Uplink port.

6
Technical Support
Thank you for selecting LevelOne products. LeveOne’s website
contains the latest user documentation and soft-ware updates
for LevelOne products.
Please contact LevelOne Technical Support through our
website.
World Wide Web
http://www.level1.com