LevelOne FGP-1031 User manual

FGP-1031
Gigabit Switch Manual
Package Contents
• FGP-1031
•
User Manual
• Power Cord

CE Marking Warning
CE marking is a certification mark that indicates conformity with health, safety, and
environmental protection standards for products sold within the European Economic Area
(EEA).The CE marking is also found on products sold outside the EEA that have been
manufactured to EEA standards. This makes the CE marking recognizable worldwide even to
people who are not familiar with the European Economic Area.
WEEE
WEEE is waste electrical and electronic equipment. It is end-of-life electrical and electronic
equipment and covers virtually everything with a plug or battery. ... The EC introduced the
WEEEDirectivein2002to addresstheenvironmentalimpactsofunwanted electricaland
electronicequipmentat end-of-lifedisposal.
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received; including interference that may cause undesired
operation.

Features
Overview
1
Product Display
2
◆
◆
◆
◆
◆
◆
◆
◆
◆
PoE Standard:
Flow control method:full duplex adopts IEEE 802.3x ,half duplex adopts Back pressure.
Port supports Auto MDI/MDIX.
supports lightning protection(secondary level requirements).
Single port supports PoE power:30W(first port outputs
Exchanging Mechanism: Store and forward.
All ports support exchange at wirespeed.
Zero-configuration:automatically supply for adaptive devices.
Panel indicator monitors operating status and helps fault analysis.
IEEE802.3af/at PoE++/HiPoE, support all ports standard detection.
Support power supply for PoE devices such as AP and network monitoring cameras connected by
Cat5/6 ethernet cables.
Port
HiPoE_60W).
◆
Automatically detecting and supplying power for powered devices conformed to IEEEE
802.3af/at PoE++/HiPoE, unmanaged PoE switch supports first port output HiPoE_60W. It can
provide a convenient service for PoE network equipments like wireless access points(AP) and IPC
surveillance cameras.
Function Switch
Mark Mode Description
N
V
S
Standard Normal
Port Isolation
Super Mode
All ports communicate freely,adapting to common data transmission environment
Switch to VLAN mode;downlink isolating from each other,uploads and downloads data
through uplink;suppress network failure like broadcast storm and virus attack
Downlink speed limitation:10M(Ultral-far transmission:250 meters)
Indicator
Status
Always ON
Always OFF
Flashes Port circuit or cunrrent over-loaded
Port Isolation LED：V
Super Mode LED：S
Port Isolation mode ON
Super mode ON
PoE LED
Orange
Green
Powered equipments connected and power supply narmally
No powered equipments connected or no power supply
Network signal communicated
Network signal not communicated
Indicator Description
Normal
Power Unconnected
Always ON
Always ON
Always ON
Always OFF
Always OFF
Always ON
Power LED:P
PoE L ink
8FE P oE+2G E UP8FE P oE+2G E UP
Hyb rid PoE S witchHyb ri d PoE S witch
123 4 9-UP 1 0-UP 567 8
100M PoE port 1000M Uplink Function switchIndicator

G
NL
Figure1.2.1 three-pin power socket(Single-phase)
Check up the power cable securely wrapped and connected to the AC power adapter connector or not.
Ensure the adequate space for heat dissipation and ventilation around the switch.
Do not stack heavy objects on the switch.
Connection of the Power Cable
1. Check up that the power supply is consistent with the marked requirements on the switch or not ;
2. The built-in power adapter is not needed, and it can be directly connected to AC100~240V and
50~60Hz;see Fig.1.2.2.
Specification of power socket
The inspection after installation
3
Installation and attentions
Desktop
When installing the switch on the desktop, the device must be placed flat on the table to keep it stable.
Please leave aside enough space between the device and other surrounding objects for good ventilation.
For the safe installation operation of switch, suggestions are as follows:
The switch adopts single-phase three-pin power socket, the middle one is the G wire,
the left one is the N wire, and the right one is the L wire. Please check before operation.
Please check up the following items after installation:
1. Enough space around the switch for heat dissipation and smooth ventilation or not.
2. The s
3. The power supply, switch, frame and other equipments are properly grounded;
upplying power of the power socket conformed to the specification of the switch.
Fig 1.1.2 Power connection schematic diagram
PoE Link
8FE PoE+2GE UP8FE PoE+2GE UP
Hybrid PoE SwitchHybrid PoE Switch
123 4 9-UP 10 -UP 567 8

FGP-1031
8*10/100Base-TX PoE port（Data/Power）
2*10/100/1000Base-TX uplinkRJ45 port (Data)
1-8 port support PoE(first port supports output HiPoE_60W)
IEEE 802.3
IEEE 802.3i 10BASE-T
IEEE 802.3u100BASE-TX
IEEE 802.3x
IEEE 802.3ab1000BASE-T
IEEE 802.3af/at//PoE++
hasivo HiPoE
5.6Gbps
4.03Mpps
2K
2.5M
10BASE-T ： Cat3,4,5 UTP(≤250 meter)
100BASE-TX ： Cat5 or later UTP(150 meter)
1000BASE-TX ： Cat6 or later UTP(150 meter)
MAX 120W （AC100-240V 50/60HZ）
210mm*150mm*35mm
270*mm220mm*68mm
0.8kg/1.2kg
Function
Single port power
Power Pin
Total Power/Input Voltage
Hybrid Gigabit PoE Switch
N:(Standard Normal)+V:(Port Isolation)+ S(Super Mode)(specific port refers to user manual)
10/100/1000BaseT（X）Auto
Default1/2(+),3/6(-);Optional 4/5(+),7/8(-)
Average15.4W;MAX 30W
Built-in power AC：100～240V 50-60Hz 1A
-10～+55°C；5%～90% RH Non coagulation
-40～+75°C；5%～95% RH Non coagulation
Desktop(optional wall+machine hanger parts)
3KV 8/20us；
Ip30
CE mark, commercial；CE/LVD ； FCC Part 15
Class B；RoHS；
5
Parameter
Model
Product
Port
Network Protocol
Port Specification
Transmission Mode
Bandwidth
Packet Forwarding
MAC Address
Buffer
Transmission
Distance
Watt
LED Indicator
Power
Operating Temperature/
Humidity
Storage Temperature/
Humidity
Product size
/Packing size
（L*W*H）
N.W/G.W(kg)
Installation
Lightning protection
level
Certificate
Store and Forward(full wirespeed)
Standby Power Consumption:≤5W
P:Power LED(Over-power LED)
Uplnik:(Green=10/100M LED+Orange=1000M LED)
V:(Port Isolation LED）
S:(Super ModLED)
Port:(Green=Link LED+Orange=PoE LED)