LevelOne OfficeCon FSW-0822 User manual

LevelOne
FSW-0822
4+4PoE Ethernet Switch
User Manual
Version 1.0-0606

FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference that
may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection requirement of
Council Directive 89/336/EEC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date. Please check with your local
distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2006,All Rights Reserved.

Unpacking Information
Thank you for purchasing FSW-0822 Ethernet Switch. Before installation, please verify
that your package contains the following items.
1. One FSW-0822 Ethernet Switch
2. One AC power cord
3. Rack-mount brackets
4. Stackable kit
5. Manual CD
Introduction
General Description
The device is a powerful, high-performance Fast Ethernet Switch, with all 8 ports capable
of 10 or 100Mbps auto-negotiation operation (NWay), which means the switch could
automatically negotiate with the connected partners on the network speed and duplex
mode. It is ideal for micro-segmenting large networks into smaller, connected subnets for
improved performance, enabling the bandwidth demanding multimedia and imaging
applications. Moreover, the 10/100Mbps auto-sensing ability provides an easy way to
migrate 10Mbps to 100Mbps network with no pain.
This switch supports PoE, which supplies power for connected devices via CAT 5 and
above twisted cables. By integrating the data transmitting cable and power cord, it
eliminates the effort constructing your network. You could easily connect a Wireless AP or
a VoIP phone to this switch without looking outlets for them. Over current protection and
circuit shorting protection are also supported to ensure the safety.
The switch is plug-n-play without any software to configure and also fully compliant with all
kinds of network protocols. Moreover, the rich diagnostic LEDs on the front-panel provide
the operating status of individual port and whole system.
Key Features
 Complies with 10BASE-T specifications of the IEEE802.3 standard
 Complies with 100BASE-TX specifications of the IEEE802.3u standard
 Complies with IEEE 802.3af PoE standard (DTE power via MDI-X)
 Provides 4 PoE ports with classification identify
 Supports 15.4W maximum per PoE port
 Supports over current protection and circuit shorting protection
 8 * RJ-45 ports for 100BASE-TX and 10BASE-T connectivity
 Supports NWay protocol for speed (10/100Mbps) and duplex mode (Half/Full)
auto-detection
 Supports MDI/MDI-X auto crossover
 Wire-speed packet filtering and forwarding rate
-1-

 Store-and-forward architecture filters fragment & CRC error packets
 Supports 1K MAC entries
 768K Bits buffer memory
 Supports extensive LED indicators for network diagnostics
 Internal universal switching power supply
 FCC Class A, CE
The Front Panel
The front panel consists of LED indicators Please refer to the following paragraph for
detailed LED definition.
LEDs Definition
The switch contain 1* power LED for the device, 1*10/100M LED for each port and 1*PoE
LED for port 1 ~ port 4.
System LED
LED Status Operation
Steady Green The switch is powered on
Power Off The switch is powered off
Port LEDs
LED Status Operation
Steady Green The port is connected
Blinking Green Data transmitting /receiving
10/100M Off No valid link on this port
Green One PoE compliant device is connecting
with this port
PoE Off There is no PoE compliant device
connecting with this port
-2-

The Rear Panel
The rear panel consists of one power receptacle and 8 RJ-45 ports. Port 1 to Port 4 also
support connecting to PoE devices.
Power Receptacle
To be compatible with the electric service standards around the world, the switch is
designed to afford the power supply in the range from100 to 240VAC, 50/60Hz. Please
make sure that your outlet standard to be within this range.
To power on the switch, please plug the female end of the power cord firmly into the
receptacle of the switch and the other end into an electric service outlet. After the power
cord installation, please check if the power LED is lit for a normal power status.
Installation
This switch can be placed on your desktop directly, or mounted in a rack. The installation
is a snap. Users can use all the features of the switch with simply attaching the cables and
turning the power on.
Before installing the switch, we strongly recommend:
1. The switch is placed with appropriate ventilation environment. A minimum 25mm
space around the unit is recommended.
2. The switch and the relevant components are away from sources of electrical noise
such as radios, transmitters and broadband amplifiers
3. The switch is away from environments beyond recommend moisture
Desktop Installation
1. Attach the provided robber feet to the bottom of the switch to keep the switch from
slipping. The recommend position has been square-marked.
2. Install the switch on a level surface that can support the weight of the unit and the
relevant components.
3. Plug the switch with the female end of the provided power cord and plug the male
end to the power outlet.
-3-

Rack-mount Installation
Rack mounting facilitate to an orderly installation when series of networking devices
being installed. The switch is supplied with rack mounting brackets and screws for rack
mounting the unit.
Procedures to Rack-Mount the Switch in the rack:
1. Disconnect all the cables from the switch before continuing.
2. Place the unit the right way up on a hard, flat surface with the front facing you.
3. Locate a mounting bracket over the mounting holes on one side of the unit.
4. Insert the screws and fully tighten with a suitable screwdriver.
5. Repeat the two previous steps for the other side of the unit.
6. Insert the unit into the rack and secure with suitable screws (optional).
7. Reconnect all the cables.
Network Cables Installation
1. Crossover or straight-through cable: All the ports on the switch support
Auto-MDI/MDI-X functionality. Both straight-through or crossover cables can be
used to connect the switch.
2. Category 3,4,5 or 5e UTP/STP cable: To make a valid connection and obtain the
optimal performance. Appropriate cables corresponding to different
transmitting/receiving speed is required. To choose a suitable cable, please refer to
the following table.
Media Speed Wiring
10 Mbps Category 3,4,5 UTP/STP
10/100 Mbps ports 100 Mbps Category 5 UTP/STP
Ports that support PoE
(Port 1~Port4) 10/100 Mbps Category5,5e UTP/STP or above.
-4-

Product Specifications
Standard
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3af Power over Ethernet
IEEE802.3x flow control
Interface
8 * 10/100 Mbps auto MDI/MDI-X RJ-45 ports
(Port1~4 support PoE power feeding)
Network Data
Rate
10/100 Mbps Auto-negotiation
Transmission
Mode
10/100Mbps Full-duplex, Half-duplex
LED indications
System: Power
Ports: 10/100M, PoE
Memory
1K MAC entries
768K Bits buffer Memory
Emission
FCC Class A,
CE
Power
Consumption
4.848 Watts (max. with no PoE Device connected)
64.32 Watts (max. with 4 x 15.4 w PoE Device connected)
Operating
Temperature
00~ 400C (320~ 1040F)
Operating
Humidity
10% - 90%(non-condensing)
Power Supply
48V 1.35A
100-240V/47-63 Hz universal input
-5-