Lex 3I510CW User manual

3I510CW / 3I510AW / 3I525CW / 3I525AW
667/800 MHz FSB / VGA / LAN / Audio /
Mini PCI / PCIe mini card
NO. 3I510CW / 3I510AW / 3I525CW / 3I525AW
Release date: July . 15 . 2010
All-In-One
Intel Atom D510 / D525, 667 / 800 MHz FSB
CF socket, Mini PCI, PCIe mini card
Multi-COM Board, Audio, LAN, SATA, USB

Copyright
Trademarks
This manual is copyrighted and all rights are reserved. It does not allow any non
authorization in copied, photocopied, translated or reproduced to any electronic or
machine readable form in whole or in part without prior written consent from the
manufacturer.
In general, the manufacturer will not be liable for any direct, indirect, special, incidental
or consequential damages arising from the use of inability to use the product or
documentation, even if advised of the possibility of such damages.
The manufacturer keeps the rights in the subject to change the contents of this
manual without prior notices in order to improve the function design, performance,
quality, and reliability. The author assumes no responsibility for any errors or omissions,
which may appear in this manual, nor does it make a commitment to update the
information contained herein.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark ofAward Software, Inc.
All other trademarks, products and or product's name mentioned here are for
identification purposes only, and may be trademarks and/or registered trademarks
of their respective companies or owners.
c Copyright 2010
All Rights Reserved.
User Manual edition 0.1, July . 23 .2010

1
1. Battery
Battery on board is consumables. We doesn’t guarantee the life time of it.
2. Fanless solution with HDD
Please be aware of specification & limitation for HDD when fanless solution
is implemented.
3. We will not give further notification if there is any change about the product
information and the manual.
4. SATA does not support Hot SWAP.
5. There would be 20% difference of WDT at room temperature.
6. Please make sure the voltage specification meet the requirement
of the equipment before plugging into the power.
7. SSD has 2 types, commercial grade and industrial grade, which provide
different read/write speed, operation temperature and life cycle.
Please contact sales for further information before ordering.
8. Caution ! Please notice that the heat dissipation problem could cause the
MB system unstable. Please handle the heat dissipation properly when
buying single MB.
9. Please avoid to approach the heat sink area and prevent being scalded when
using the Fanless products.
10. If the users repair, modify or destroy any component of product
unauthorized, We would not take responsibility or provide warranty.
11. DO NOT apply any other material onto the thermal pad in case reducing
cooling performance.
12. It is important to install a System Fan toward the CPU to prevent the
possibility of overheating / system hang up issues from D510 / D525 series
of motherboard or else customer is required to have well cooling system to
dissipate heat from CPU.
Warning !
+
-

2
Hardware Notice Guide
1. Before installing the power supply with this motherboard, please attach the 12V/DC
( 2 pin connector )of the adapter to motherboard first.
After that, plug the adapter power to AC outlet.
Always normally shut down the computer before you move the system unit or remove
the power supply from the motherboard.
Please unplug the 12V/DC ( 2 pin connector ) of the adapter from motherboard first.
Then unplug the adapter from the AC outlet.
Please refer to procedure from the photo 1
2. There will be high possibility to burn out the CPU if you change/ modify any parts of the
CPU cooler.
3. Please wear wrist strap and attach it to a metal part of the system unit before handling a
component.
You can also touch an object that is of ground connection or with metal surface if you don't
have wrist strap.
4. Please be careful when you handle this product. Pay attention to & don't touch the
sharp-pointed components at the bottom PCB .
5. Please pay attention to this: Remove or change any components form the motherboard
will VOID the warranty of the motherboard you purchased .
6. Before you install/remove any components or make any jumper setting on the motherboard,
please make sure to disconnect the power first.
( Please follow the instructions as of this guide )
7. Please only use single sided Mini PCI card, do not use the double sided Mini PCI card
which is not suitable.
8. This does not support 16 bit mini PCI card
9. Please follow this instruction carefully when using the "POWERON after PWR-Fair" function.
When the DC power adaptor runs out of power, unplug it from the DC current;
when power returns plug it back in only after 5 seconds. If there is a power outage,
unplug it from the AC current, when power returns plug it back in only after 30 seconds.
Otherwise it will cause system locking or serious damage.
Remark 1:
Always insert/unplug the 12V/DC ( 2 pin connector ) horizontally & directly from the
motherboard.
DO NOT twist the 12V/DC ( 2 pin connector ) gently, it is designed to fit snugly .
Moreover, erratic pull / push testing with the DC Jack might cause the unpredictable
damage to the component & system unit.
*

3
Photo 1
2
1
3
1
2
3
Insert
Unplug

4
The 3I510AW/3I525AW and 3I510CW/3I525CW areAll-In-One boards which could apply
to the use of Networking, POS or Automation Control Board. These are designed to
combine all necessary input and output affects interfaces, which makes them to be
ideal All-In-One control board for the demand of Networking, POS and
Automation Control applications. 3I510AW/3I525AW and 3I510CW/3I525CW are the
perfect platform for a whole range of small form factor.
High-performance and power-efficient communication platform, the embedded motherboard
of 3I510AW/3I525AW/ and 3I510CW/3I525CW are specially designed for advanced
embedded car PC or POS system applications where the economical use of power is in
high demand. With the sizable memory bandwidth of on board 1GB DDR2/DDR3 module
and the flexibility of expanding the memory to 4GB with DDR2/DDR3 SODIMM
(maximum of total 4GB memory), 3I510CW/3I525CW will ensure the high performance
levels required for today's most popular POS/Automation control applications including
Embedded Car PC, POS, ATM, Kiosk and Panel PC applications.
3I510AW/3I525AW and 3I510CW/3I525CW could have option for Intel or
Realtek LAN chipset with 10/100/1000 Mbps Ethernet for seamless broadband connectivity.
With the Wake-On LAN function and the PXE function in BIOS for Realtek LAN chipset,
it is perfect control board for networking devices.
3I510AW/3I525AW and 3I510CW/3I525CW also support with multi-COM ports of
five RS232 and one RS422/485 to meet the needs of multi-COM ports connectivity.
Not only Compact Flash card, these can also have expansion for PCIe mini card and
Mini PCI Card. In addition, there are multi-ports of Hi-Speed USB 2.0 to enhance the
host controller interface which will ensure the high performance level and flexible expansion.
The Compact Flash socket supports ATA interface. Asingle Flash chip holds the system
BIOS, and you can change the Flash BIOS by the Utility Update.
The All-In-One motherboards, 3I510AW/3I525AW and 3I510CW/3I525CW are fully
compatible with industry standards, plus technical enhancements, and thousands of
software applications developed for IBM PC/AT compatible computers. These control logic
provides high-speed performance for the most advanced multi user and
multitasking applications available today.
Chapter-1
General lnformation

5
1. Intel Atom D510/D525 CPU (FSB 667/800 MHz)
2. Intel Atom D510/D525 and ICH8M and Integrated Graphic Chip (DVMT 4.0)
3. 3I510CW / 3I525CW – 1GB of on board DDR2 / DDR3 memory and
1 x DDR2/DDR3 SODIMM socket (up to 4GB)
3I510AW / 3I525AW – 1 x DDR2 / DDR3 SODIMM socket (up to 4GB)
4. On board SSD flash memory 2 / 4 / 8 GB (option)
5. Support 2 x Realtek GbE or 1 x Realtek and 1 x Intel LAN GbE Chips
6. 18 bits LVDS Interface on Board (3I510CW / 3I525CW only)
7. Support 1 x Compact Flash Card Socket on Board
8. Support 2 x SATA ports
9. Support Mini PCI Socket on board and 2 x PCIe mini card for USB and PCIe interface
10. On board DC-IN +12V Power Supply or Wide range DC-IN from +6V to +35V (option)
11. Compact PCB Dimension: 145 x 102 mm (3.5 inch)
1-1 Major Feature

6
1. CPU: Intel Atom D510/D525, 1.66 / 1.8GHz CPU ( FSB 667 / 800 Mhz )
2. ChipSet: Intel Atom D510/D525 and ICH8M
3. Memory: 3I510CW / 3I525CW - 1GB of on board DDR2 / DDR3 memory and
1 x DDR2/DDR3 SODIMM socket (up to 4GB)
3I510AW / 3I525AW - 1 x DDR2/DDR3 SODIMM socket (up to 4GB)
4. VGA: Internal Graphics Memory with dynamic video memory technology (DVMT4.0)
5. I/O Chip: F81801U and F81216AD IO chipset
6. SATA: Two SATA ports with independent DMA operation supported
7. NAND flash memory (Option): Support Compact Flash card type II for ATA interface
On board SSD 2 / 4 / 8 GB (option)
8. LAN: 2 x Realtek RTL8111DL or Intel 82583V (LAN 1 only) and
Realtek RTL8111DL PCIE LAN chipset
9. Storage Device: 1 x 50 pins Compact Flash Socket
10. Serial Port: 5 x RS232 + 1 RS422 / 485 or 5 x RS485 + 1 RS232 (optional)
11. USB: 7 x USB 2.0 (2 external + 5 internal ports)
12. Keyboard & Mouse: 1 x 6 pin wafer connector
13. Sound: Intel HD audio specification Rev. 1.0 Compliant
14. LVDS (3I510CW / 3I525CW only): support 18bits LVDS interface and resolution of
1366 x 768 maximum
15. WDT / DIO: Hardware watch dog timer support, 0~255 sec programmable
Hardware digital Input & Output, 8 x DI / 8 x DO
16. Touch screen (3I510CW / 3I525CW only): C8051F321 USB/COM interface
touch screen controller, support 4-, 5-, 8- wire Analog resistive touch screen
17. Audio Amplifier (optional): 6-W/CH into an 8-ΩLoad from a 12-V Supply.
Up to 92% Efficient, Class-D operation
18. Expansion interface: 1 x Mini PCI socket for PCI Rev. 2.2 interface &
2 x PCIe mini card support USB and PCIe by one interface
19. BIOS: Award BIOS version V6.1
20. Dimension: 145 x 102 mm (3.5 inch)
21. Power: On board DC-IN Convert into system power +12VAD/±5% to +5V/±5% and
+3.3V/±5% or Wide range DC-IN from +6V to +35V (option)
22. Power Consumption: Please refer to page 79
1-2 Specification

7
1-3 Installing the SO-DIMM
1. Align the SO-DIMM with the connector at a 45 degree angle.
2. Press the SO-DIMM into the connector until you hear a click.

8
Notices:
1.The connectors are designed to ensure the correct insertion. If you feel resistance,
check the connectors & golden finger direction, and realign the card.
2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of
the card firmly.

9
1-3-1.1 Removing the SO-DIMM
1. Release the SO-DIMM by pulling outward the two retaining clips and the SO-DIMM
pops up slightly.
2. Lift the SO-DIMM out of its connector carefully.

10
1-4 Installing the Mini PCI card
1.Align the Mini PCI card with the connector at
a 45 degree angle. 2. Press the Mini PCI into the connector until you hear
a click.
Notices:
1.The connectors are designed to ensure the
correct insertion. If you feel resistance, check the
connectors & golden finger direction, and realign the card.
2. Make sure the retaining clips (on two sides of the slot)
lock onto the notches of the card firmly
1-4-1.1 Removing the Mini PCI card
1. Release the Mini PCI card by pulling outward
the two retaining clips and the card pops up slightly. 2. Lift the mini PCI card out of its connector carefully.

11
1-5 Directions for installing the Mini Card
1. Unscrew the screw on the board
3. Gently push down the Mini Card and screw the screw back.
2. Plug in the Mini Card in a 45 angle

3I510CW / 3I510AW / 3I525CW / 3I525AW
12
1-6 Packing List
Please contact with your dealer if any of these items is missing or damaged
on delivery. And please keep all parts of the delivery package with packing
materials in case if you need to deliver or store the product in the future.
*The packing list above is for the users who purchase single motherboard. The users
who purchase the board with chassis may refer to the packing list in the Assembly Guide.
1 Mainboard
2 Utility CD Disk
3 PS/2 Cable
4 DC Cable
5 SATA Power Cable
123456
78910 11
6 SATA Data Cable
7 User’s Manual
8 DC 12V Power Adapter (2P)
9 USB Cable
10 COM Cable
11 Audio Cable (Line out & Mic in)

13
Hardware Installation
This chapter provides the information how to install the hardware of
3I510AW / 3I510CW / 3I525AW / 3I525CW.
Please follow section 1-6, 2-1 and 2-2 to check the delivery package and unpack
carefully. Please follow the jumper setting procedure.
Chapter-2
2-1 Unpacking Precaution
The 3I510AW / 3I510CW / 3I525AW / 3I525CW board has been well packed with
an anti-static bag to protect its sensitive components and circuitry from damage due to
static electric discharge.
You should follow these
steps to protect the board from the static electric
discharge whenever you handle the board:
1. Ground yourself by a grounded wrist strap at all times when you
handle the 3I510AW / 3I510CW / 3I525AW / 3I525CW.
Well secure the ALLIGATOR clip of the strap to the end of the shielded wire lead from
a grounded object. Please put on and connect the strap before handling the
3I510AW / 3I510CW / 3I525AW / 3I525CW for harmlessly discharge any static electricity
through the strap.
2. Please use anti-static pad to put any components, parts, or tools on the pad whenever
you work on them outside the computer. You may also use the anti-static bag instead of
the pad. Please ask your local supplier for necessary parts on anti-static requirement.
3. Do not plug any connector or set any jumper when the power is on.
1. Do not touch the board or any other sensitive components without all necessary
anti-static protection.
2. Please pay attention to the voltage limitation of DC-IN12 V 5 %.
Overuse of DC-IN voltage limitation or change to another power adapter
( not provided with this system ) will VOID warranty.
NOTE!
+
-

14
2-2 Unpacking checkup
First of all, please follow all necessary steps of section 2-1 to protect 3I510AW / 3I510CW
/ 3I525AW / 3I525CW from electricity discharge. With reference to section 1-6,
please check the delivery package again with following steps:
1. Unpack the 3I510AW / 3I510CW / 3I525AW / 3I525CW board and keep all
packing material, manual and driver disc etc, do not dispose !
2. Is there any components lose or drops from the board? DO NOT CONTINUE
TO INSTALL THIS BOARD! CONTACT THE DEALER YOU PURCHASED THIS
BOARD FROM, IMMEDIATELY.
3. Is there any visible damage on the board? DO NOT CONTINUE TO INSTALL
THIS BOARD!CONTACT THE DEALER YOU PURCHASED THIS
BOARD FROM, IMMEDIATELY.
4. Check your optional parts (i.e. DDR, CF etc.), all necessary jumpers
setting to jumper pin-set, and CMOS setup correctly.
Please also refer to all information of jumper settings in this manual.
5. Check your external devices (i.e. Add-On-Card, Driver Type etc.)
for complete add-in or connection and CMOS setup correctly.
Please also refer to all information of connector connection in this manual.
6. Please keep all necessary manual and driver disc in a good condition for future
re-installation if you change your Operating System.

15
2-3 Dimension 145 x102 mm (3.5 inch)
2.99
10.48
32.52
65.91
91.29
107.82
119.97
130.47
137.18
146
3.68
15.75 51.25 97.68
102
2.99
20.45
35.42
56.51
6.5
6.28
6.2
7.15
14.3
11.48

16
2-4 Layout - 3I510AW / 3I510CW / 3I525AW / 3I525CW
JVU5
CC6
CC11
CC5
JVC4
CC4
CC3
CA2
CC1
CC2
CA1
CPI11
CL1
JSC3
CKM1
CL2
CU2
MPCE1
CF1
CU1
CL21
CG11
CG1
CPI1
JVC1
JSB1
CFP1
CA3
CU7CU5 CU3
CU4
CU8
CAR1CAL1
CU6
CPO1
SWP1
CPP1
FAN1
LVDS1
MPCE2
JSD1
CIO1
CIO2
CT1
LED1
JVL1
JVP1
SODIM1
CPI12 COS1
CO1
COH1

17
2-5 Diagram- 3I510AW / 3I525AW
JVU5
CC6
CC5
JVC4
CC4
CC1
CC2
CL1
JSC3
CKM1
CL2
CU2
MPCE1 CF1
CU1
CG11
CG1
CPI1
JVC1
JSB1
CA3
CU7CU5 CU3
CU4
CU8
CAR1
CAL1
CU6
CPO1
SWP1
FAN1
MPCE2
CIO1
CIO2
LED1
SODIM1
CPI12 COS1
CO1
COH1
CC3

18
2-5-1 Diagram- 3I510CW / 3I525CW
JVU5
CC6
CC5
JVC4
CC4
CC1
CC2
CL1
JSC3
CKM1
CL2
CU2
MPCE1 CF1
CU1
CG11
CG1
CPI1
JVC1
JSB1
CFP1
CA3
CU7
CU5 CU3
CU4
CU8
CAR1
CAL1
CU6
CPO1
SWP1
CPP1
FAN1
LVDS1
MPCE2
JSD1
CIO1
CIO2
CT1
LED1
JVL1
JVP1
SODIM1
CPI12 COS1
CO1
COH1
CC3