Lex Slim Dimmer User manual

Slim Dimmer
Portable Single Dimmer
User Manual
(Model LDT1.8K)
LM-SLIMDIM000-Rev. 002
TYPE 3R Rainproof TYPE 1 Indoor or
TYPE 3R Rainproof
TYPE 3R Rainproof TYPE 1 Indoor or
TYPE 3R Rainproof
PowerGATE®
Switches & Panels
PowerPLUS
Installed Distribution Boxes
TM
PowerRAMP®
Cable Protectors
Power Control Solutions
™
Dimming & Control
™
PowerHOUSE
Portable Distribution Boxes
TM
PowerPARTS
Wiring Devices
TM
PowerRACK
Rolling Distribution Racks
TM
WeldingRACK
WR6
TM
PowerFLEX
Cable Assemblies
TM
LuxCommander®
Portable Work Lights
Smart Power™
Energy Storage

The Slim Dimmer is a unique single portable 1.8kW dimming solution that can be used individually or as a part of
a complete dimming system. It is perfect for lm, television, studios, location shoots, or anywhere you need just
one dimmer or just one more dimmer.
Unpacking and Inspection
Before you begin your installation check the shipment carefully to conrm it arrived complete and undamaged.
1. Check the contents against the packing list to ensure the device is the correct model
2. Check the panel for loose or broken components, which might have resulted from shipping
3. Inspect for signs of damage to wiring devices, circuit breakers, handles or device enclosure
If there is any damage to the Slim Dimmer contact Lex Products toll free at 800-643-4460 or email
[email protected].
Safety Notice
The Slim Dimmer is built and tested with safety as a primary consideration, but all electrical equipment must be
used with care. Observe all normal precautions when operating this dimmer.
1. Review all instructions before use and save for future reference
2. The device shall be connected to a mains outlet with overcurrent protection and grounding.
3. This product is for use in dry locations only
4. Unplug dimmer from power before servicing
5. Do not modify dimmer or housing in any manner
Slim Dimmer Components
Fig. 1
Introduction
NEMA 5-15 Power Inlet
Safety Cable Mounting Point
Level Control Slider
Fig. 2
15A Circuit Breaker
NEMA 5-15 Receptacle
LED Display

1. Line Power Connection
• Connect the Slim Dimmer to a 120VAC 15A 60Hz power source using the NEMA 5-15 plug (Fig. 2)
• If the breaker (Fig. 2) trips, check the power source and cables being used before resetting
• Do not power the unit from a dimmed circuit
2. Load Power Connection
• The Slim Dimmer portable dimmer can control incandescent loads
• To prolong lamp life, set the control output to zero before connecting the load, see below
• Plug load(s) up to the capacity of the dimmer, into the NEMA 5-15 receptacle (Fig. 2) using properly
grounded and appropriately rated cords
1. Hanging
• If desired, a C-clamp may be attached to the dimmer for hanging, using a thread adapter and the 14”-20
threaded insert in the case of the dimmer
— Mounting hardware is available from Lex Products
• The ¼”-20 threaded insert can also accommodate a variety of alternate photographic and motion picture
mounting or hanging products
— Additional thread adapters are available from Lex Products.
• When hanging a safety cable (not included) must be used
• The dimmer is equipped with two holes on the face of the enclosure (Fig. 1) through which a safety cable
may be threaded and xed to a suitable structure (such as around the pipe to which the dimmer is clamped)
2. Resting
• The dimmer case may get hot when operated at or near full load
• The dimmer should only be hung or placed on ooring, equipment or furniture that is not susceptible to heat
damage.
1. The dimmer’s digital display will illuminate when powered
2. Slide the dimmer’s built-in fader to provide the desired lighting level
3. The digital display will indicate a percentage (0-100%), permitting the dimmer to be easily and repeatedly set to a
specic level
• It also permits multiple independent Slim Dimmers to be easily set to the same level
Connecting Power and Control Wiring
Installation
Setting Up for Operation

1. If the dimmer does not operate as expected, check the power source and check all cables and connectors
2. Be sure the push to reset breaker is on pushed in (Fig. 2)
• The dimmer is protected by an on-board 15 Amp, push-to-reset circuit breaker
• During normal operation the breaker “button” will be ush with the surface of the unit
• When the breaker is tripped, the button will pop up above the surface of the unit
3. LED display does not illuminate.
• Check to be sure that the power is being supplied to the dimmer
• Ensure the push to reset breaker is ush with the surface of the unit
4. Connected load is ghosting and will not shut off
• Slide the Level Control slider back and forth between 0% and 100%
• If the load remains on at 0%, contact Lex Products Support or your dealer for repair
WE DELIVER THE POWERTM
Lex Products Corporation
11 Forest Parkway
Shelton CT 06484
203.363.3738
203.363.3742 Fax
Lex West
12701 Van Nuys Boulevard
Suite Q
Pacoima, CA 91331
818.768.4474
818.768.4040 Fax
www.lexproducts.com
[email protected]
800.643.4460
© Copyright Lex Products 2021
Produced in the United States of America
All Rights Reserved.
Lex Products logo and lexproducts.com are
trademarks or registered trademarks of Lex
Products in the United States,
other countries, or both.
Troubleshooting
LM-SLIMDIM000 - Rev. 002
Technical Support
• Lex Products is available to help answer any product related inquiries
• For any questions or technical advice, please call toll free 800-643-4460 or email [email protected].