Lexmark Optra E310 Owner's manual

Xerox Work Center 390
Toner Part Num.: 113R462
Page Yield @ 5%: 3,000 pgs
Resolution: 6,000 dpi
Xerox Docuprint
P8E/P8EX/WC385
Toner Part Num.: 13R00296
Page Yield @ 5%: 5,000 pgs
Resolution: 1,200 dpi
Lexmark Optra
E310/E312/E312L
Toner Part Num: 13T0301
Page Yield @ 5%: 3,000 pgs
Resolution: 1,200 dpi
Toner Part Num: 13T10
Page Yield @ 5%: 6,000 pgs
Resolution: 1,200 dpi
#1 Phillips Screwdriver
Small Flat Blade Screwdriver
Needlenose Pliers
Soft Lint-Free Cloth
Cotton Swabs
Anhydrous Isopropyl Alcohol
Vacuum or Compressed Air
Technical Instructions Printers /OEM Info Tools 1
E-mail: [e-mail] Website: www.futuregraphicsllc.com
Step 1
Using a Phillips screwdriver remove the
two screws from the top of the cartridge.
(See Photo1)
Step 2
With a small flat blade screwdriver release
the three clips located on the front of the
cartridge under the handle.
(See Photo 2)
Step 3
To separate the two sections, lift up on
the front of the toner hopper. Be careful
when separating the two sections, toner
will spill out of the toner hopper.
(See Photo 3)
NOTE: Do not break off the clips on the
back of the hopper.
Photo 1
Photo 2
Photo 3
E310TECH
US1800 394.9900
Int’l +1 818 837.8100
FAX [phone]
Int’l +1 818 838.7047
DALLAS, USA
US 1 877 499.4989
Int’l+1 972 840.4989
FAX [phone]
Int’l +1 972 840.1750
ATLANTA, USA
US 1 877 676.4223
Int’l +1 770 516.9488
FAX [phone]
Int’l +1 770 516.7794
MIAMI, USA
US 1 800 595.429
Int’l+1 305 594.3396
FAX [phone]
Int’l +1 305 594.3309
SANFORD,USA
US 1 800 786.9049
Int’l+1 919 775.4584
FAX [phone]
Int’l +1 919 775.4584
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX [phone]
Int’l +1 905 712.9502
NEWYORK, USA
US 1 800 431.7884
Int’l +1 631 345.0121
FAX [phone]
Int’l +1 631345.0690
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX [phone]
Int’l +62 02 9548.2635
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX [phone]
MONTEVIDEO,URY
URY 02 902.7206
Int’l +5982 900.8358
FAX [phone]
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX [phone]
MELBOURNE,AUS
AUS 1 800 003. 100
Int’l+62 03 9561.8102
FAX [phone]
Int’l [phone]
CORPORATE
LOS ANGELES, USA

Step 4
Using dry compressed air or a vacuum,
clean out both sections of the cartridge.
Step 5
Remove the three screws holding the end
caps on each side of the cartridge.
(See Photos 4 and 5)
Photo 4
Photo 5
Photo 6
Step 6
Removethe drum shutter arm from the
contact end cap, rotate the drum shutter
up towards the handle on the cartridge
until the tab on the shutter fits through the
notch on the end cap. (See Photo 6)
NOTE: Let the shutter dangle; Do not
removethe shutter from the other end
cap.
Step 7
Pull the contact end cap from the side of
the cartridge.
(See Photo 7)
NOTE: Do not lose the white bearing that
fits on the foam feed roller axle
(See Photo 8)
Photo 7 Photo 8
Need trust-worthy, detailed Technical
Instructions for another engine?
Visit: www.futuregraphicsllc.com
2 Lexmark Optra E310 Technical Instructions
Photo 9
Step 8
Located ONLY on the contact end cap of
the fax cartridge is a blown 100m fuse. This
fuse must be replaced each time this car-
tridge is recycled. Replace the fuse.
(See Photo 9)
Notes

Photo 11
Step 11
Remove the two metal gear axles from the
gear side of the hopper.
(See Photo 12)
Photo12
Step 12
On each end of the PCR thereis a screw
that holds the PCR saddles in place,
remove the two screws.
(See Photo13)
Photo 13
Step 13
Lift out the PCR. NOTE: Do not lose the
gear thatfits on the end of the PCR.
(See Photo 14)
Clean the PCR using a PCR cleaner.
Photo 14
Need help with a particular remanu-
facturing problem?
Call the Technical Resource Center from
8am - 5pm PST: 800 394.9900
Lexmark Optra E310 Technical Instructions 3
Step 10
Photo 11 shows the gear alignment of the
hopper. Remove the five white gears from
the hopper.
(See Photo 11)
Photo 10
Step 9
With the drum shutter still attached,
remove the end cap from the gear side of
the hopper.
(See Photo 10)
NOTE: Once again there is a white bearing
on the foam feed roller axle. Do not lose
the bearing.
Notes

Photo 18
Photo 19
Photo 15
Photo 20
Photo 21
Photo 17
Photo 16
4 Lexmark Optra E310 Technical Instructions
E-mail: [e-mail] Website: www.futuregraphicsllc.com
Step 14
Remove the three screws that
hold the wiper blade.
(See Photo 15)
Step 15
Lift out the wiper blade straight
up to remove.
Step 16
Grab the drum by the gears and
lift the drum out of the hopper.
Clean the drum using a lint free
cloth. (See Photo16)
Step 17
Remove the black gear from
the developer roller axle.
(See Photo 17)
Step 18
Release the two clips that hold the devel-
oper roller end cap.
(See Photo 18 and 19)
Remove the end cap.
Step 19
Slide the developer roller out through the
side of the hopper.
(See Photo 20)
Clean the developer roller using a dry lint-
free cloth.
Step 20
Remove the two screws that hold the
doctor blade.
(See Photo 21)
Step 21
Lift the doctor blade up. It may be neces-
sary to remove the small foam strips that
are connected to the back of the doctor
blade. Clean the doctor blade using
alcohol and a cotton swab.
Step 22
Apply a seal to the toner hopper.
Step 23
Reassemble in reverse order.

ENGINE FACT SHEET
P
Pr ro od du uc ct t
Drum
Technical Guide
Toner
D
De es sc cr ri ip pt ti io on n
Sinonar
Cartridge Remanufacturing Instructions - Lexmark E210
65gm Bottle
I
It te em mN Nu um mb be er r
E210SNR
E210TECH
E210TNR65
P
Pa ac ck kQ Qt ty y. .
5/100
1
10
FUTURE GRAPHICS PRODUCT LISTING
P
PR RI IN NT TE ER RM MO OD DE EL L
Lexmark E210
Samsung ML-1010
Samsung ML-1020M
Samsung ML-1210
Samsung ML-1220M
Samsung ML-1250
Samsung ML-1430
Samsung ML-4500
Samsung ML-4600
O
OE EM MN NU UM MB BE ER R
1OS0150
ML1210D3
ML1210D3
ML1210D3
ML1210D3
ML1210D3
ML1210D3
ML4500D3
ML4500D3
PRINTER MODEL COMPATIBILITY
2
2

ENGINE FACT SHEET
P
PR RI IN NT TE ER RM MO OD DE EL L
Lexmark Optra E310
Lexmark Optra E312
Lexmark Optra E312L
Olivetti PGL 8L
Samsung ML-5000A
Samsung ML-5000G
Samsung ML-5050G
Samsung ML-5100A
Xerox Docuprint P8e
Xerox Docuprint P8ex
Xerox WorkCentre 385
Xerox WorkCentre 390
O
OE EM MN NU UM MB BE ER R
1OS0150
ML1210D3
ML1210D3
ML1210D3
ML1210D3
ML1210D3
ML1210D3
ML4500D3
ML4500D3
113R296
113R296
113R462
PRINTER MODEL COMPATIBILITY
P
Pr ro od du uc ct t
Cartridge Box
Cartridge Tech Guide
Developer Roller
Docotr Blade
Cartridge Tech Guide
Drum
Fuse
PCR
Seal
Seal
Toner
Toner
Wiper Blade
D
De es sc cr ri ip pt ti io on n
Two-Color Self-Adhesive
Remanufacturing Intructions
Doctor Bar With Sponge
AEG
Drum Unit Reset Fuse, Fax
For Printer (Not for Fax) , New, Onyx
Adhesive Goldseal
Adhesive Onyx, Reinforced
Bulk Bag, 22 lb Per-Fil - Boxof 1, Sold per box
160gm Bottle
I
It te em mN Nu um mb be er r
ML5000LABEL
ML5000TECH
ML5000DVRROL
ML5000DRBLADEG
ML5000AEG
ML5000DRUMG
ML5000FUSED
ML5000PCR
ML5000GOLDSEAL
ML5000SEALONYXR
ML500010KG
ML5000TNR160
ML5000WBLADEG
P
Pa ac ck kQ Qt ty y. .
100
1
10
10
5/60
5/50
10
10
50
50
1
10
10/200
FUTURE GRAPHICS PRODUCT LISTING
Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment.
None of FG's products are genuine OEM replacement parts and no affiliation or sponsorship is to be implied between FG and any OEM.