LF Style Selections 0402374 User manual

1
1
ATTACH YOUR RECEIPT HERE
Serial Number____________________________ Purchase Date_________________________
ITEM #0402374
VANITY WITH ENGINEERED
STONE TOP
MODEL #30BV8045-0560
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.
Français p. 7
Español p. 13
Style Selections® is a registered trademark of
LF, LLC. All Rights Reserved.

2
2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Vanity 1
B Backsplash 1
C Left Door 1
D Right Door 1
E Drawer 1
F Vanity Base 1
AD
E
F
C
B

3
3
PREPARATION
SAFETY INFORMATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt
to assemble the product. Contact customer service for replacement parts.
Estimated assembly time: 60 minutes and 24 hours for adhesive to dry.
Tools required for assembly (not included): Phillips Screwdriver, Utility Knife or Scissors,
Power Drill, Drill Bit, Wall Mounting Hardware, Adhesive
Helpful Tools (not included): Measuring Tape, Level
Please read and understand this entire manual before attempting to assemble, operate or install the
product. If you have any questions regarding the product, please call customer service at
1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.
WARNING
• Some steps are more easily handled with two adults.
• Assembly and unpacking requires 2 adults.
• Do not try to pry off top from vanity. Damage to top or vanity may occur.
CAUTION
• Before installation, carefully use scissors or utility knife to cut and unwrap all parts. Make sure you
do not discard the hardware.
• Use care when assembling your new vanity; take your time and follow the assembly
instructions closely.
HARDWARE CONTENTS
Screw Touch-Up Pen
(Not to Scale)
Qty. 8 Qty. 1
AA BB
W3504

4
4
ASSEMBLY INSTRUCTIONS
2. Clean area where the vanity (A) will
be permanently located. Find and
mark the locations of the wall studs
behind the wall.
Place vanity (A) against wall in desired
location. Be sure vanity (A) location is
accessible to water supply and drain lines
before mounting.
IMPORTANT SAFETY STEP!
Drill hole through vanity (A) mounting
area. Use proper hardware
(not included) to secure vanity (A) to
wall stud with at least one fastener, such
as a wood screw or toggle bolt. If
possible, secure vanity (A) to two wall
studs for increased stability.
1.Place vanity (A) on it’s back on a
scratch-free surface. Insert screw (AA)
into the predrilled holes in the vanity
base (F) using a Phillips screwdriver.
3. Apply adhesive to the unpolished back
side and bottom of the backsplash (B).
Position the backsplash (B) as shown in
Fig. 2 on the top and against the wall.
Clean any excess adhesive before
allowing to dry.
2
3
9DQLW\0RXQWLQJ
$UHD
6WXG
9DQLW\0RXQWLQJ$UHD
$'+(6,9(
Unpolished
Back
B
AA
A
1
AA Screw x 8
F
A

5
5
4. It may be easier to remove the drawer (E)
prior to installing the faucet and drain set
(not included). To remove the drawer,
fully extend drawer (E) out and locate the
black plastic levers located on the metal
glide tracks on the left and right sides of
the drawer box. At the same time, push
down on the right plastic lever and up on
the left plastic lever while gently pulling
the drawer (E) out from vanity (A) to
disengage the drawer box from the
glides. Set the drawer (E) aside until
final step.
5. To reinstall the drawer (E) pull the
glides all the way out from vanity (A), and
line them up to the tracks on drawer (E).
Carefully engage both tracks and slowly
push drawer (E) back into the cabinet
(A). Keeping the drawer (E) centred as
you push.
Note: There is no need to activate any
levers to reinstall the drawer.
4
5
6
$&%
E
E
A
Warning: Do not use tool to pry off top
from Wood Cabinet. Damage to top or
Wood Cabinet may occur.

6
6
CARE AND MAINTENANCE
• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
Make sure to dry the wood immediately with a soft cloth or towel.
• The engineered stone top can be cleaned using standard stone cleaning agents available
at your local supplier.
• Tips for using touch-up pen (BB): For scratches, stroke in direction of scratch; for worn areas,
stroke in direction of wood grain. Rub excess colorant promptly with a soft cloth.
For replacement parts, call our customer service department at
1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.
REPLACEMENT PARTS LIST
Part Description Part number
B Backsplash P30BV8045-B
C Left Door P30BV8045-C
D Right Door P30BV8045-D
E Drawer P30BV8045-E
F Vanity Base P30BV8045-F
G Adjustable Hinge P30BV8045-G
H Handle P30BV8045-H
BB Touch-Up Pen P30BV8045-BB
Printed in China
W3504
B
C D
BB
E
F
HG