LF WT7424-WB User manual

VANITY SET: WT7424-WB
INSTALLATION INSTRUCTIONS
VANITY CABINET + VANITY TOP + MIRROR
SINK BASE
Version 1.0
WT7424-WB
WT7430-WB
WT7436-WB
www.legionfurniture.com

Silicone
Pencil/Marker
Caulk Gun
Pliers Electric Drill
with DrillBits
Stud Finder Hammer
Philips
Screwdriver
Level
Safety Glass Tape Measure
Soft Cloth
or Blank
et
2
VANITY SET: WT7424-WB
VANITY CABINET + VANITY TOP + MIRROR
PRODUCT PACKAGE COMPONETS/TOOLS REQUIRED
VANITY COMBINATION
TOOLS REQUIRED FOR INSTALLATION
(NOT INCLUDED)
P-TRAP AND POP AND POP-UP
INSTALLATION DIAGRAMMAIN COMPONENTS
INSTALLATION ACCESSORIES
Wall Anchors Screws 1 1/4"
x 2 x 2
Other tools may be required
Silicon
Washer
Sink
Pop-up
Mounting
Ring
Silicon Washer
Brass Nut
Rubber Washer
Tail Pipe
Vanity Base Cabinet
Glass Basin
Wall Mount Mirror
x 1
x 1
x 1
www.legionfurniture.com

3
DIMENSIONS & SPECIFICATIONS
Front View Side View
ATTENTION! Due to manufacturing process any dimensions may have a tolerance up to 3/8". All sizes are for reference only.
It is highly recommended to pull all dimensions of actual model for installation and measuring purposes.
ATTENTION! If two or more vanity cabinets are installed next to each other there will be a
visible seam between vanity tops and between vanity cabinets or between drawer base cabinets.
VANITY SET: WT7424-WB
VANITY CABINET + VANITY TOP + MIRROR
Mirror
W
35 2/5"
34 3/5"
21 1/2"
20 3/10" 3/5"
7 1/2"
4 7/10"
1 9/10"
2 2/5"
2 2/5"
B
W
W
A
W
W
21 1/2"
22"
MODEL
T9313-24W 24" 9 3/10"
T9313-30W 30" 12 2/5"
T9313-36W 36" 15 2/5"
WAB
M
M
18 4/5"
24 9/10"
30 4/5"
22"
28 3/20"
34 1/10"
www.legionfurniture.com

4
INSTALLATION STEPS
All WT7424-WB vanity cabinets by
are installed from the inner side of the drawer
to avoid damage during transportation. Open
the drawers to install the handles. Unscrew
every handle and install them from the outer
side of the doors and drawers. See Figure 1
Note:It is highly recommended not to use
electric drill to avoid overtightening the screws
during handle installation.
INSTALL DOOR & DRAWER HANDLES
See Figure 1
Prior to installation of the glass vanity top you
must apply a silicone layer by a perimeter of
the vanity base cabinet and carefully lay down
the vanity top on top of the vanity cabinet.
See Figure 2
Note (single vanity sink cabinet installation):
Vanity top is slightly wider than the actual
cabinet. Make sure that outstanding edges are
equal at left and right sides.
Apply a silicone layer on the back side of the
vanity top that will be adjacent to the wall.
Allow the silicone dry for 48 hours prior to the
first use of the vanity cabinet.
VANITY CABINET ASSEMBLY
See Figure 2
VANITY SET: WT7424-WB
VANITY CABINET + VANITY TOP + MIRROR
LegionFurniture
come pre-assembled. All door and drawer handles
www.legionfurniture.com

Mirror Back View
Peel-Off
Film
5
INSTALLATION STEPS
MIRROR INSTALLATION
CHECK OUT NEXT PAGE WITH VARIETY OF COMBINATIONS EXAMPLES
Using a tape measure find a length of the vanity
top and divide it by 2. The result of the division
will be a center of the top. Using a tape measure
find the center of the top and mark a dot on the
wall just right above theb top using a pencil.
Using a level tool find a location of a second dot
to draw a vertical line that will serve as
installation center for the mirror.
Measure the distance between installation
brackets of the mirror and divide it by 2. The
result of the division will be a distance between
the drawn center line and center of a drilled
holes. Mark a center of the first hole and using a
level find and mark a location for a second
hole.Using an electric drill make the holes.
See Figure 3
Apply a silicone inside each hole. Insert wall
anchors (a hammer may be needed if the holes
are too tight.) Using a Philips Screwdriver insert
the mounting screws into the wall anchors (do
not screw in completely as the brackets of the
mirror must hang on top of the screws.) Align
the mirror with the wall and carefully hang the
mirror on the screws. Both screw heads must be
inserted into the brackets on the mirror during
hangin process. Make sure that the mirror is
secured safely on the wall.
See Figure 4
Note:
If the brackets can not reach the screws or
the mirror is loose after hanging you need to
adjust the screws using the Philips Screwdriver.
IMPORTANT! Using a stud finder locate wooden
studs. Screws for mounting mirror must be installed in
the wooden studs to support weight of the mirror.
IMPORTANT:
At the bottom of the back side of the mirror there are two foam blocks
with adhesive surface covered by a film. Remove the film before hanging
the mirror. These blocks will stick to the wall for extra support, leveling,
and preventing from moving.
Figure 3
Figure 4
WALL
WALL
WALL
WALL
VANITY SET: WT7424-WB
VANITY CABINET + VANITY TOP + MIRROR
www.legionfurniture.com

Retain these installation instructions
for future reference!
VANITY SET: WT7424-WB
VANITY CABINET + VANITY TOP + MIRROR
Legionfurniture reserves the right to modify this installation instructions at any time.
It is a customer's sole resposibility to inquiry for the updates of the installation instructions.
www.legionfurniture.com