LF Style selections LWUSTCB User manual

F
1
Serial Number Purchase Date
ATTACH YOUR RECEIPT HERE
ITEM #5120860
MODEL #LWUSTCB
LONG HANG TOWER
2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Top panel 1
B Top frame 1
C Back post 2
D Front post 2
E Left side frame 1
F Right side frame 1
G Connect beam 2
H Bottom stretcher 1
I Shelf 1
J Bottom panel 1
K Metal pole 1
A
C
C
E
G
G
H
I
J
K
D
D
B
STYLE SELECTIONS is a trademark or registered
trademark of LF, LLC. All rights reserved.
Call customer service at 1-877-888-8225,8 a.m. - 8 p.m., EST, Monday - Sunday.

43
HARDWARE CONTENTS (not shown actual size)
PREPARATION
SAFETY INFORMATION
WARNING
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
Please read and understand this entire manual prior to assembling the product.
1. Do not allow children to climb or play in or around this product.
2. Use this unit for its intended purpose only. Do not use shelves as step ladder.
3. To avoid damage, assemble the product on a sturdy, level and protective surface.
4. Make sure all bolts/screws are tightly fastened before the unit is used.
5. Check bolts/screws periodically and tighten them if necessary.
MAXIMUM LOAD: 25 lb
(EVENLY DISTRIBUTED)
MAXIMUM LOAD: 20 lb
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 50 minutes
Tools Required for Assembly (not included): Rubber Mallet, Marking Pencil, Stud Finder, Phillips
Screwdriver, Power Drill and Drill Bit.
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM WEIGHTS INDICATED. USE
WITH PRODUCTS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN
INSTABILITY CAUSING POSSIBLE INJURY. DISTRIBUTE WEIGHT EVENLY.
AA
EE II
BB
FF GG
CC DD
1/4” x 12 mm
Bolt
Qty. 40
M4 x 35 mm
Screw
Qty. 22
L-bracket
Qty. 4
Hex wrench
Qty. 1
M 4 x 15 mm
Bolt
Qty. 2
Metal plate
Qty. 2
Pole holder
Qty. 2
Back Crosser
Qty. 1
M5 x 65 mm
Screw
Qty. 1
LLJJ KK
Drywall Anchor
Qty. 1

5 6
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
1. Attach connect beams (G) and bottom stretcher (H)
between the side frames (E and F) using 1/4” x 12 mm
bolts (AA). Tighten with hex wrench (CC).
4. Attach top panel (A), shelf (I) and bottom panel (J) to
assembly. Secure in place with M4 x 35 mm screws (BB).
5. Attach pole holders (FF) to metal pole (K), securing
with M4 x 15 mm bolts (EE).
6. Attach pole holders (FF) to top frame (B), using
1/4” x 12 mm bolts (AA). Tighten with hex wrench (CC).
2. Attach top frame (B), left side frame (E) and right side
frame (F) to back posts (C) and front posts (D), using
1/4” x 12 mm bolt (AA). Tighten with hex wrench (CC).
3. Attach L-bracket (DD) to assembly, using
1/4” x 12 mm bolt (AA). Tighten with hex wrench (CC).
1 4
5
6
2
3
AA
FF
EE
DD
AA
AA
BB
FF
FF
FF
AA
AA
AA
DD
CC
CC
CC
G
K
H
F
A
I
E
J
F
B
B
B
E
D
E
F
Hardware Used
Hardware Used
Hardware Used
Hardware Used
Hardware Used
Hardware Used
1/4” x 12 mm Bolt
M4 x 15 mm Bolt
L-bracket
M4 x 35 mm Screw
1/4” x 12 mm Bolt
1/4” x 12 mm Bolt
1/4” x 12 mm Bolt
Hex wrench
Pole holder
Hex wrench
Hex wrench
Hex wrench
x 4
x 22
x 2
x 4
x 10
x 16
x 4
x 1
x 2
x 1
x 1
x 1
AA
BB
EE
DD
AA
AA
AA
CC
FF
CC
CC
CC
G
C
C
E
F

7 8
ASSEMBLY INSTRUCTIONS
8. If you buy more than one unit, you can collect
more style.
9. Secure units together by attaching the metal plates (II)
with the 1/4” x 12 mm bolts (AA) into the holes. Tighten
with hex wrench (CC).
NOTE: Must install step 7 for all secured units
9
II
AA CC
Hardware Used
Metal plate
1/4” x 12 mm Bolt
Hex wrench
x 2
x 6
x 1
II
AA
CC
Wall
7. Adjust oor levelers to level the unit against the wall
where desired. Using top frame (B) as a template, mark
one mounting holes location on the wall. Drill one pilot
holes into the wall where previously marked. Make sure
that the drilled holes can t for the wall anchors (sold
separately) properly. Press the anchors into the holes
and gently tap with a hammer until ush in the holes. If
the mounting hole coincides with a wooden stud, there is
no need wall anchor. Align top frame (B) and back cross-
ers (GG) over the drywall anchors (KK) and secure with
M5 x 65 mm screw (JJ). Tighten securely with phillips
screwdriver.
7
Hardware Used
BJJ
KK GG
Drywall Anchor x 1
x 1
KK
Back Crosser
x 1
JJ
GG
M5 x 65 mm
Screw 8
CARE AND MAINTENANCE
LIMITED LIFETIME WARRANTY
This product is warranted to the original purchaser. If there is a failure in this unit due to defects in
materials or workmanship, the manufacturer will repair or replace this item at our discretion without
charge. Warranty is void if product has been assembled incorrectly, misused, abused by
overloading, altered in any way or damaged due to accident. This warranty is not transferable and
does not cover chipping, aking, scratches, rust, dents, or other damages to the surfaces of this
product. Responsibility of the manufacturer is limited to repair or replacement of this product. The
manufacturer is not responsible for consequential, incidental, or other damages or losses resulting
from product failure.
This warranty is in lieu of all other expressed warranties. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specic legal rights and you may have other rights which vary from state
to state.
• Periodically check to make certain all components are properly positioned, free from damage
and rmly connected.
• Use a soft, clean cloth that will not scratch the surface when dusting.
• Never use water to clean the furniture as it may cause damage to the nish.
• Wipe clean using a damp cloth and a mild cleaner. Wipe dry with a clean cloth.
• In the event that the furniture is stained or otherwise damaged during use, it is recommended
you call a professional to repair the furniture.
• Keep furniture away from direct sunlight as it may damage the nish.
• It is best to keep the furniture in a climate-controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood.
PART DESCRIPTION PART #
A Top panel 00LWUSTCB-A
B Top frame 00LWUSTCB-B
C Back post 00LWUSTCB-C
D Front post 00LWUSTCB-D
E Left side frame 00LWUSTCB-E
F Right side frame 00LWUSTCB-F
G Connect beam 00LWUSTCB-G
H Bottom stretcher 00LWUSTCB-H
I Shelf 00LWUSTCB-I
J Bottom panel 00LWUSTCB-J
K Metal pole 00LWUSTCB-K
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-877-888-8225,8 a.m. - 8 p.m., EST,
Monday - Sunday.

9
Printed in Vietnam
Date: 2022-10-05
Rev. 0001-A
PART DESCRIPTION PART #
AA 1/4” x 12 mm Bolt 00LWUSTCB-AA
BB M4 x 35 mm Screw 00LWUSTCB-BB
CC Hex wrench 00LWUSTCB-CC
DD L-bracket 00LWUSTCB-DD
EE M4 x 15 mm Bolt 00LWUSTCB-EE
FF Pole holder 00LWUSTCB-FF
GG Back Crosser 00LWUSTCB-GG
II Metal plate 00LWUSTCB-II
JJ M5 x 65 mm Screw 00LWUSTCB-JJ
KK Drywall Anchor 00LWUSTCB-KK
CH Complete hardware 00LWUSTCB-CH
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-877-888-8225,8 a.m. - 8 p.m., EST,
Monday - Sunday.
AA
DD FF
II
GG
KK
JJ
EE
BB CC
F
A
C
C
E
G
G
H
I
J
K
D
D
B