LG-Nortel LDP-7008D User manual

Important Safety Information

Important Safety Information

Important Safety Information

LDP-7000 Series Model
LDP-7004D
LDP-7008D
LDP-7004N
1

Input/Output Devices and Button
LDP-7008D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
LCD Display
Handset
Headphone Socket (Ear/Mic Mode)
Speaker
Speaker Button
Hold/Save Button
Volume Button
Loop Button
Message Waiting LED
Dnd/Fwd Button
Call Back Button
Flexible Button
Speed Button
Trans/Pgm Button
Handsfree Microphone
2

1
2
3
4
5
6
7
8
9
10
LCD Display (LDP-7004D only)
Handset
Speaker
OHD Button
Hold/Save Button
Message Waiting LED
Trans/Pgm Button
Speed Button
Flexible Button(Loop Button)
Volume Button
Input/Output Devices and Button
LDP-7004D
3

Used for handset call.
The optional earphone into the
handset to provide a hands-
free phone conversation.
Outputs tones and voice.
Used to access speed dialing,
speed programming, saved
number redial.
The DND (Do Not Disturb)
feature blocks all incoming
calls. When DND is active, the
red LED in this button is
illuminated.
It is also used to activate call
forward, e.g. to another station
or voicemail. When call
forward is activated, the red
LED flashes.
This button put a call on hold
or save information when
programming.
Speaker toggles the
speakerphone state, and the
red LED is illuminated when
the speakerphone is active.
On Hook Dial allows 7004N&D
users to dial and monitor call
state without lifting the
handset.
Handset
Earphone-Jack
Speaker
Speed Button
Dnd/Fwd
Button
Hold/Save
Button
Speaker Button
OHD Button
Item Description
Input/Output Devices and Button
4

Shows dialed and incoming
numbers (where applicable)
and on the 7008D it will
display other information about
call status, dialing directories
and message information.
This button is used to initiate a
call transfer (TRS) or to enter
programming mode (PGM).
The last two (7004D/7004N) or
six (7008D) flex buttons can
be assigned outside line
presentation or as one-touch
feature access. (See codes at
rear of guide)
A station can initiate a call
back request to a busy station.
Once that station becomes idle,
the initiating station is signaled.
The volume button adjusts the
audio levels for ringing,
handset and speakerphone or
OHD functions .
Microphone for hands-free
speakerphone function.
Loop Button(s) are required for
presentation of outside lines to
the telephone. At least one is
required per telephone.
LCD Display
Trans/PGM
Button
Flexible
Button
Call back
Button
Volume Button
Hand-free
Microphone
Loop Button
Item Description
Input/Output Devices and Button
5

Cable Connection
A
Cable connection
A Connect the telephone cord (curly cord)
to the handset and the other end to the
handset jack at the bottom of the telephone.
BConnect the line cable to the port at the
bottom of telephone and the other end to
the wall socket.
CConnect the Headphone to the headphone
jack on the left side of the telephone.
(As viewed from the front.)
※Note: 7004N and 7004D does not
support integral headphone mode.
BC
6

Placing an Outside Call
●Lift handset, press OHD/Speaker or dial from live keypad.
●Dial 9.
●Dial the desired number.
Placing an Intercom Call
Placing an Outside Call on Hold
Retrieving a Outside Call on Hold
Re-directing an Incoming Call
(Call Pick-up)
Answering an Waiting Call
Basic Function
●Lift handset, press OHD/Speaker or dial from active keypad.
●Dial the station number.
●While connected to an external call, press [HOLD] button.
●Press the flashing flexible button.
※Note: calls will automatically recall after pre-defined time
When you hear another phone ringing in your area,
●Lift handset, press OHD/Speaker or dial from live keypad.
●Dial 7.
●Dial the extension number of the ringing station.
●You will be connected automatically to the caller.
●Press the flashing CO button.
7