LG LB500K User manual

APPENDIX G :
FCC ID : BEJLB500K
USER’S MANUAL

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Important Precautions

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.

A3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand base
1. Align the hooks on the stand base with the matching slots in the base of
the monitor.
2. Insert the hooks into slots.
Important
This illustration depicts the general model of connection. Your monitor may
differ from the items shown in the picture.
To Remove the Stand Base
- Do not force to remove the Stand Base, but remove the screws on the
back first for your safety.
- Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only
the stand base. The product may fall and get
damaged or injure your foot.
Hook
Stand Base

A4
Connecting the Display
Using the Computer
1. Connect the signal cable. When attached, tighten the thumbscrews to secure
the connection.
2. Connect the power cord into a proper power outlet that is easily accessible and
close to the display.
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
Wall-outlet type*
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display
may differ from the view as shown.
PC-outlet type*
PC
MAC
Power Cord Signal Cable
Analog signal
D-sub*
* Varies according to model.

A5
Control Panel Functions
Front Panel Controls
Buttons
Use these buttons to choose or adjust items in
the On Screen Display.
MENU Button
Use this button to enter or exit the On Screen
Display.
Use this button to turn the display on or off.
This Indicator lights up green when the display
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
Power Button
Power (DPMS)
Indicator
Use this button to enter a selection in the On Screen
Display.
AUTO/SELECT
Button
Control Function

A6
Control Panel Functions
Control Direct Access Function
Bring up Contrast and Brightness adjustment.
100
100
PROCESSING
AUTO CONFIGURATION
When adjusting your display settings, always press the
AUTO/SELECT button before entering the On Screen
Display(OSD). This will automatically adjust your display image
to the ideal settings for the current screen resolution size
(display mode).
The best display mode is 1024x768.
AUTO adjustment function
CONTROLS LOCKED
CONTROLS UNLOCKED
This function allows you to secure the current control settings,
so that they cannot be inadvertently changed. Press and hold
the MENU button and button for 3 seconds: the message
“CONTROLS LOCKED” appears.
You can unlock the OSD controls at any time by pushing the
MENU button and button for 3 seconds:
the message “CONTROLS UNLOCKED” will appear.
CONTROLS LOCKED/UNLOCKED
:
MENU and

A7
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the or Buttons. When the icon you want
becomes highlighted, press the AUTO/ SELECT Button.
Use the Buttons to adjust the item to the desired level.
Accept the changes by pressing the AUTO/SELECT Button.
Exit the OSD by Pressing the MENU Button.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
AUTO/SELECT
AUTO/SELECT
MENU
MENU

A8
NOTE
The order of icons may differ depending on the model (A8~A10).
* This function is available for designated models only.
On Screen Display(OSD) Selection and Adjustment
To adjust the brightness and
contrast of the screen
BRIGHTNESS
CONTRAST
COLOR
POSITION
TRACKING
SETUP
Main menu Sub menu Reference
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
PRESET
9300K
6500K
R/G/B(User Color)
GAMMA
To adjust the position of the
screen
To customize the color of the
screen
To customize the screen status
for a user's operating environment
To improve the clarity and
stability of the screen
: Adjustable
BRIGHTNESS
CONTRAST
V POSITION
H POSITION
CLOCK
PHASE
LANGUAGE
OSD POSITION
BEEP
*

A9
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
OSD Adjust Description
BRIGHTNESS
To adjust the brightness of the screen.
CONTRAST
To adjust the contrast of the screen.
Vertical Position
To move image up and down.
Horizontal Position
To move image left and right.
To adjust the brightness and contrast of the screen
To adjust the position of the screen
OSD Adjust Description
BRIGHTNESS / CONTRAST
88
100
PRESET
RED
GREEN
BLUE
GAMMA
9300K/6500K
Select the screen color.
• 9300K: Slightly bluish white.
• 6500K: Slightly reddish white.
Set your own color levels.
Set your own gamma value.(-50~50)
On the monitor, high gamma values
display the whitish images and low
gamma values display the high
contrast images.
To customize the color of the screen
OSD Adjust Description
COLOR
PRESET 9300K 6500K
RED
GREEN
BLUE
GAMMA
POSITION
61
39

A10
On Screen Display(OSD) Selection and Adjustment
To improve the clarity and stability of the screen
OSD Adjust Description
TRACKING
CLOCK
PHASE
To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
CLOCK
PHASE
LANGUAGE ENGLISH
ON
BEEP
SETUP
OSD POSITION
ELAPSED TIME H
0
1024x768/60Hz
PRESET MODE
To customize the screen status for a user's operating environment
OSD Adjust Description
To choose the language in which the
control names are displayed.
To adjust position of the OSD window
on the screen.
To select beep ON or OFF.
ELAPSED TIME
To display the use time of display.
LANGUAGE
OSD POSITION
BEEP*
NOTE
* This function is available for designated models only.

No image appears
A11
Troubleshooting
Check the following before calling for service.
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator green?
Is the power indicator
amber?
Do you see an "INPUT
SIGNAL OUT OF
RANGE" message on
the screen?
Do you see a "NO
SIGNAL "message on
the screen?
Check and see if the power cord is connected
properly to the power outlet.
Press the Power button.
Adjust the brightness and the contrast.
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
No image appears
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator green?
Is the power indicator
amber?
Do you see an "INPUT
SIGNAL OUT OF
RANGE" message on
the screen?
Do you see a "NO
SIGNAL "message on
the screen?
Check and see if the power cord is connected
properly to the power outlet.
Press the Power button.
Adjust the brightness and the contrast.
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
No OSD
Do you see
"CONTROLS LOCKED"
when you push any
button?
Unlocked OSD showing "CONTROLS
UNLOCKED" by pressing the MENU and
button at the same time for 3 seconds.

Display image is incorrect
Have you installed the display driver?
A12
Troubleshooting
Display Position is
incorrect.
On the screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Color is not seen
usually.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check if the window color is set properly.
If the color set is 256 colors and this makes
unusual color change color setting from 256 color
to highest color(ex:true color(32bit)) as sequence
of control panel --> display --> setting.
Have you installed the
display driver?
Do you see the
message of
"Unrecognized monitor,
Plug&Play(VESA DDC)
monitor found"?
Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lge.com.
Be sure to check if the video card supports
Plug&Play function.

A13
Specifications
NOTE
Information in this document is subject to change without notice.
15 inches (38.1cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
15 inches viewable
0.3 mm pixel pitch
Horizontal Freq. 30 - 63kHz (Automatic)
Vertical Freq. 56 - 75Hz (Automatic)
Input Form Separate TTL, Positive/Negative
Signal Input 15 pin D-Sub Connector
Input Form RGB Analog (0.7Vp-p/75ohm)
Max VESA 1024 x 768@75Hz
Recommend VESA 1024 x 768@60Hz
DDC 2B
Normal :
28W
Stand-by/Suspend ≤3W
Power Off ≤3W
Width 35.60 cm / 14.02 inches
Height 35.98 cm / 14.17 inches
Depth 15.17 cm / 5.97 inches
Net 4.0 kg (8.82 lbs)
Tilt -5˚~30˚
AC 100-240V 50/60Hz 0.6A
Operating Conditions
Temperature 10˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity 5 % to 95 % non-Condensing
Attached( ), Detached ( O )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
TCO99
Display
Sync Input
Video Input
Resolution
Plug&Play
Power
Consumption
Dimensions
&Weight
(with tilt stand)
Tilt Range
Power Input
Environmental
Conditions
Tilt Stand
Signal cable
Power cord
Regulations

A14
Specifications
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
*12
13
14
* Recommended
Unlike CRT monitors, which require a high refresh rate to minimize flickering, TFT
technology is inherently flicker-free. If possible, configure your computer for 1024 x 768
addressability at 60Hz vertical refresh rate.
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
31.468
31.468
31.469
35.000
37.861
37.500
35.156
37.879
48.077
46.875
49.725
48.363
56.476
60.023
70
70
60
66.67
72.8
75
56.25
60
72
75
75
60
70
75
VGA
VGA
VGA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
VESA wall mounting
Connected to another object (stand
type and wall-mounted type. This
monitor accepts a VESA-compliant
mounting interface pad.)
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most computer
stores

Reference Guide
for Precaution,
Service, Warranty
and Diskette Install
English
Deutsch
Français
Italiano
Español
Nederlands
Português

i
Monitor Registration
The model and serial numbers are found
on the rear of this unit. These numbers
are unique to this unit and not available to
others. You should record requested
information here and retain this guide as
a permanent record of your purchase.
Staple your receipt here.
Date of Purchase :
Dealer Purchased From
:
Dealer Address :
Dealer Phone No. :
Model No. :
Serial No. :
English
Important Precautions ..................................................1
DDC (Display Data Channel) .......................................1
Energy Saving Design .................................................2
Service ..........................................................................2
Deutsch
Wichtige Hinweise ........................................................2
DDC (Display Data Channel) ......................................3
Energieversorgung .......................................................3
Wartung ........................................................................3
Français
Consignes de Sécurité ..................................................4
DDC (Display Data Channel) .......................................4
Caractéristique D’économie D’énergie ........................5
Maintenance du Moniteur .............................................5
Italiano
Precauzioni Importanti ..................................................5
DDC (Display Data Channel) Canale Dati del Monitor 6
Modello Conforme alla Normativa sul Risparmio
Energetico ......................................................................6
Manutenzione ................................................................6
Español
Precauciones Importantes ............................................7
DDC (Canal de despliegue de información) ................7
Diseño de Ahorro de Energía .......................................8
Servicio ..........................................................................8
Nederlands
Belangrijke voorzorgsmaatregelen ..............................8
DDC (Display Data Channel) .......................................9
Energiebesparingssysteem ..........................................9
Onderhoud .....................................................................9
Português
Precauções Importantes .............................................10
DDC (Display Data Channel) .....................................10
Sistema de Gerenciamento de Energia ....................11
Manutenção .................................................................11
Regulatory Information
FCC Compliance Statement .....................................11
Canadian DOC Notice ................................................11
CE Conformity Notice (for Europe) .............................12
Low Radiation Compliance (MPR II)...........................12
TCO95 ..........................................................................12
TCO99 ..........................................................................13
EPA (U.S.A only)..........................................................14
NOM MARK (Mexico only)..........................................14
Warranty
the United States and Canada - CDT Monitor ...........15
the United States and Canada - LCD Monitor............16
Australia - CDT & LCD Monitor...................................17
Brazil - CDT & LCD Monitor ........................................18
Mexico - CDT Monitor..................................................19
the United Kingdom - CDT&LCD Monitor ..................21
Monitor Driver Installation
Monitor Driver Installation ..........................................22
USB Install Guide ........................................................22

1
English
Important Precautions
This unit has been engineered and manufactured to
assure your personal safety, but improper use can
result in potential electrical shock or fire hazard. In
order not to defeat the safeguards incorporated in this
monitor, observe the following basic rules for its
installation, use, and servicing. Also follow all
warnings and instructions marked directly on your
monitor.
On Safety
Use only the power cord supplied with the unit. In case you
use another power cord, make sure that it is certified by the
applicable national standards if not being provided by the
supplier. If the power cable is faulty in any way, please
contact the manufacturer or the nearest authorized repair
service provider for a replacement.
Operate the monitor only from a power source indicated in
the specifications of this manual or listed on the monitor. If
you are not sure what type of power supply you have in
your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous.
So are frayed power cords and broken plugs. They may
result in a shock or fire hazard. Call your service technician
for replacement.
Do not Open the Monitor.
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when
the power is OFF.
Contact your dealer if the monitor is not operating
properly.
To Avoid Personal Injury :
Do not place the monitor on a sloping shelf unless
properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across
thresholds or deep pile carpets.
To Prevent Fire or Hazards:
Always turn the monitor OFF if you leave the room for
more than a short period of time. Never leave the
monitor ON when leaving the house.
Keep children from dropping or pushing objects into the
monitor's cabinet openings. Some internal parts carry
hazardous voltages.
Do not add accessories that have not been designed for
this monitor.
During a lightning storm or when the monitor is to be left
unattended for an extended period of time, unplug it from
the wall outlet.
Do not bring magnetic devices such as magnets or
motors near the picture tube.
On Installation
Do not allow anything to rest upon or roll over the power
cord, and do not place the monitor where the power cord is
subject to damage.
Do not use this monitor near water such as near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement, or
near a swimming pool.
Monitors are provided with ventilation openings in the
cabinet to allow the release of heat generated during
operation. If these openings are blocked, built-up heat can
cause failures which may result in a fire hazard. Therefore,
NEVER:
Block the bottom ventilation slots by placing the monitor
on a bed, sofa, rug, etc.
Place the monitor in a built-in enclosure unless proper
ventilation is provided.
Cover the openings with cloth or other material.
Place the monitor near or over a radiator or heat source.
LCD Monitor only
Do not rub or strike the Active Matrix LCD with anything
hard as this may scratch, mar, or damage the Active Matrix
LCD permanently.
Do not press the LCD screen with your finger for a long
time as this may incur some afterimages.
Some dot defects may appear on the screen, like Red,
Green or Blue spots on the screen. However, this will have
no impact or effect on the monitor performance.
If possible, use the recommended resolution to obtain the
best image quality for your LCD monitor. If used under any
modes except the recommended resolution, some scaled
or processed images may appear on the screen. However,
this is the characteristics of the LCD panel which has a
fixed resolution.
On Cleaning
Unplug the monitor before cleaning the face of the
monitor screen.
Use a slightly damp (not wet) cloth. Do not use an
aerosol directly on the monitor screen because
overspray may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials.
They make an ideal container in which to transport the
unit. When shipping the unit to another location, repack it
in its original material.
DDC (Display Data Channel)
DDC is a communication channel over which the monitor
automatically informs the host system (PC) about its
capabilities.
DDC protocol
①DDC1/DDC2B
An uni-directional communication channel.
②DDC 2AB/DDC2B+/DDC2Bi
A bi-directional communication channel.
Note
PC must support DDC functions to do this.

2
Mode
Normal
Standby
Suspend
Off
Horizontal
Sync.
On
Off
On
Off
Vertical
Sync.
On
On
Off
Off
LED
Color
Green
Amber
Amber
Amber
English Deutsch
Energy Saving Design
This monitor complies with the EPA's Energy Star program,
which is a program designed to have manufacturers of
computer equipment build circuitry into their products to
reduce power consumption during time of non-use.
When this monitor is used with a Green or EPA Energy
Star PC, or a PC with a screen blanking software following
the VESA Display Power Management Signalling (DPMS)
protocol, this monitor can conserve significant energy by
reducing power consumption during periods of non-use.
There are 2 signal lines, 4 modes of operation.
; Normal, Standby, Suspend and Off.
When you awaken your PC by hitting a key or moving the
mouse, the monitor will also awaken to its normal operating
mode, indicated by the green Power LED light.
Note
The energy saving Design for monitors only work when
connected to computers that have energy saving
features.
Service
Unplug the monitor from the wall outlet and refer servicing
to qualified service personnel when :
The power cord or plug is damaged or frayed.
Liquid has been spilled into the monitor.
The monitor has been exposed to rain or water.
The monitor does not operate normally following the
operating instructions. Adjust only those controls that are
covered in the operating instructions. An improper
adjustment of other controls may result in damage and
often requires extensive work by a qualified technician to
restore the monitor to normal operation.
The monitor has been dropped or the cabinet has been
damaged.
The monitor exhibits a distinct change in performance.
Snapping or popping from the monitor is continuous or
frequent while the monitor is operating. It is normal for
some monitors to make occasional sounds when being
turned on or off, or when changing video modes.
Do not attempt to service the monitor yourself, as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
Wichtige Hinweise
Bei der Konstruktion bzw. Herstellung dieses Monitors
wurde insbesondere auf eine höchstmögliche
Betriebssicherheit geachtet. Um eine eventuell durch
Fehlbedienung verursachte Brand - und Stromschlaggefahr
auszuschliessen, sollten Sie jedoch bei Inbetriebnahme
und Benutzung des Gerätes die nachfolgenden
Sicherheitshinweise genau beachten. Beachten Sie
ausserdem die am Monitorgehäuse angebrachten
warnhinweise und Anweisungen.
Zur Sicherheit
Benutzen Sie ausschliesslich das mitgelieferte abgeschirmte
Netzkabel. Falls Sie ein anderes als das vom Hersteller
gelieferte Netzkabel verwenden, achten Sie darauf, daß es der
nationalen Norm entspricht. Wenn das Netzkabel in irgendeiner
Weise defekt ist. Wenden Sie sich an den Hersteller oder den
nächsten autorisierten Reparaturservice, um Ersatz zu erhalten.
Stellen Sie sicher, dass die angelegte Netzspannung den
Geräteanforderungen entpricht (siehe dazu die technischen
Daten in diesem Handbuch bzw. die Angaben auf der Rückseite
des Monitors). Bei Fragen zur Spannungsversorgung den
Händler zu Rate ziehen.
Vermeiden Sie eine Überlastung des benutzten Stromkreises
oder einer eventuell eingesetzten Mehrfachstec1Sie ausserdem
unbedingt darauf, dass Netzkabel und -stecker unbeschädigt
sind, um Brand und Stromschlaggefahr auszuschliessen.
Lassen Sie alle notwendigen Reparaturen von einem
qualifizierten Service-Techniker ausführen.
Öffnen Sie den Monitor auf keinen Fall.
Im Innern des Monitors befinden sich keinerlei vom Benutzer
zu wartende Teile.
Da allerdings selbst bei ausgeschaltetem Monitor im Gehäuse
gefährliche Spannungen anliegen, sollte bei einer Fehlfunktion
des Monitors unbedingt der Händler zu Rate gezogen werden.
Um eine Verletzung des Benutzers auszuschliessen:
den Monitor keinesfalls auf einer instabilen unterlage abstellen.
ausschliesslich vom Hersteller empfohlene Monitorsockel und
-tische benutzen.
den Monitor nicht mit einem Rolltisch über hohe Türschwellen
oder sehr weiche Teppiche fahren.
Um die Gefahr eines Brandes oder elektrischen Schlages
auszuschliessen:
den Monitor ausschalten, wenn Sie ihn für längere Zeit nicht
benutzen bzw. wenn Sie das Büro oder die Wohnung
verlassen.
auf keinen Fall irgendwelche Gegenstände in die
Gehäuseschlitze stecken, da spannungsführende Teile
beruhrt oder Kurzschlüsse verursacht werden könnten.
Keine Zubehörteile installieren, die nicht für diesen Monitor
geeignet sind.
bei Gewitter oder wenn Sie den Monitor für längere Zeit nicht
benutzen, das Netzkabel aus der Steckdose ziehen.
keine magnetisch aufgeladenen Gegenstände wie permanent-
magneten oder Motoren id die Nähe des Bildschirms bringen.
Zur Installation
Stellen Sie keine Gegenstände auf das Netzkabel. Plazieren Sie
den Monitor so, dass das Netzkabel auf keinen Fall beschädigt
werden kann.

3
Betreiden Sie den Monitor nicht in der Nähe von Wasser
(Waschbecken etc.) bzw. in Räumen mit überdurchschnittlich
hoher Luftfeuchte.
Die Schlitze im Monitorgehäuse dienen der Belüftung des
Geräts.
Diese Öffnungen dürfen auf keinen Fall blockiert oder vedeckt
werden, da sie den Monitor vor Überhitzung schützen und einen
störungsfreien Betrieb des Geräts garantieren. Um die Gefahr
eines Brandes weitgehend auszuschliessen, sollten Sie deshalb:
den Monitor niemals auf eine weiche Unterlage stellen, da auf
diese Weise die Belüftungsschlitze an der Gehäuseunterseite
blockiert werden.
den Monitor nicht eingebaut betreiben, sofern nicht für eine
ausreichende Belüftung gesorgt ist.
die Belüftungsschlitze des Monitors auf keinen Fall mit einer
Textil- oder sonstigen Abdeckung blockieren
den Monitor nicht in die Nähe einer Heizung oder auf einen
Heizkörper stellen.
Nur LCD-Monitor
Das Aktivmatrix-LCD nicht mit etwas härterem als HB reiben
oder schlagen, da das das Aktivmatrixdisplay dauerhaft
verkratzen oder beschädigen kann.
Nicht mit Ihrem Finger für längere Zeit auf den LCD-Bildschirm
drücken, da das Schattenbilder hervorrufen kann.
Einige Punktdefekte können auf dem Bildschirm erscheinen.
Das können rote, grüne oder blaue Stellen auf dem Bildschirm
sein. Das hat jedoch keinen Einfluß auf die Leistungsfähigkeit
des Bildschirms.
Verwenden Sie, wenn möglich, die empfohlene Auflösung, um
die bestmögliche Bildqualität für den LCD-Monitor zu erzielen.
Bei Verwendung anderer Modi als die empfohlene Auflösung
können einige skalierte oder verarbeitete Bilder auf dem
Bildschirm erscheinen . Hierbei handelt es sich jedoch um die
Eigenschaften der LCD-Anzeige mit einer festen Auflösung.
Zur Reinigung
Ziehen Sie das Netzkabel des Monitors, bevor Sie die
Vorderseite des Bildschirms reinigen.
Verwenden Sie ein leicht feuchtes (kein nasses) Tuch.
Sprühen Sie ein Spray niemals direkt auf den Bildschirm, da
zuviel Spray einen elektrischen Schock verursachen kann.
Zur Verpackung
Das Verpackungsmaterial des Monitors sollte aufbewahrt
werden, um das Gerät gegebenenfalls lagern, transportieren
oder versenden zu können. Beispielsweise sollte der Monitor
im Falle einer Störung wie auf dem Karton dargestellt
ausschliesslich in der Originalverpackung zur Reparatur
zurückgeschickt werden.
DDC (Display Data Channel)
DDC ist ein Kommunikationskanal, über weiche Sie von lhrem
Monitor automatisch über das verbundene System (PC) und
seine Fähigkeiten informiert werden.
DDC Protokoll
①DDC1/DDC2B
Ein unidirektionaler Kommunikationskanal.
②DDC 2AB/DDC2B+/DDC2Bi
Ein bidirektionaler Kommunikationskanal.
Anmerkung
Der PC muß für DDC Funktionen eingerichtet sein.
Energieversorgung
Dieser Monitor entspricht den Richtlinien des EPA Energy Star
Program. Er beinhaltet neuartige Schaltungen, um den
Energiever-brauch wahrend der Nichtbennutzung zu verringern.
Wird dieser Monitor mit einem grünen oder EPA Energy Star-PC
oder einem PC mit einer Software verwendet, die den Bildschirm
gemäß des VESA Display Power Management Signaling
(DPMS)–Protokolls abschaltet, läßt sich eine beträchtliche
Energiemenge sparen, indem der Stromverbrauch bei Inaktivität
gesenkt wird.
Es gibt 2 Signalreihen und 4 Betriebsmodi.
; Normal, Standby, Bereitschaft und Aus.
Wenn Sie den PC durch Drücken einer Taste oder Bewegen der
Maus wieder aktivieren, wird der Monitor ebenfalls in den
Normalmodus umgeschaltet, was durch die grüne Netz-LED
angezeigt wird.
Hinweis
Die Energiesparfunktion für Monitore kann nur bei Anschluß
an Computern verwendet werden, die ebenfalls
Energiesparfunktionen unterstützen
Wartung
Bei folgenden Fehlerbedingungen ist der Netzstecker des
Monitors zu ziehen und der Kundendienst zu benachrichtigen:
Wenn der Netzstecker beschadigt oder das Netzkabel
ausgefranst ist.
Wenn Flussigkeit in den Monitor gelaufen ist.
Wenn der Monitor Regen oder Feuchtigkeit ausgesetzt
worden ist.
Wenn der Monitor trotz Befolgung aller
Bedienungsanweisungen nicht ordnungsgemass arbeitet.
Benutzen Sie ausschliesslich die Bedienelemente, die in den
Hinweisen dieses Handbuchs beschrieben werden. Werden
andere Bedienelemente geandert oder verstellt, konnen
Schaden entstehen, die nur von einem qualifizierten Service-
Techniker behoben werden konnen.
Wenn der Monitor fallengelassen und das Gehause
beschadigt wurde.
Wenn beim Betrieb des Monitors haufig oder lang anhaltend
knackende oder knallende Nebengerausche auftreten.
Hiermit sind nicht die typischen Gerausche gemeint, die beim
Ein- oder Ausschalten des Monitors zu horen sind.
Fuhren Sie keine Wartungsarbeiten selbst durch. Durch Offnen
oder Entfernen wichtiger Abdeckungen werden
spannungsfuhrende Teile freigelegt, so dass eine erhohte
Gefahrdung besteht. Fur Wartungsarbeiten in diesen Bereichen
ist der Kundendienst zustandig.
Modus
Normal(Max.)
Standby
Bereitschaft
Aus
Hori
Sync.
Ein
Aus
Ein
Aus
Vert.
Sync.
Ein
Ein
Aus
Aus
LED
Farbe
Grün
Gelb
Gelb
Gelb
Deutsch