LG Qua Tab 01 Quick start guide

Notes on Usage
Be sure to read these notes on usage before use
June 2015, 1st Edition
-7-
Do not cover or wrap the product with bedding, etc. while using or
charging the product. Doing so might cause fire, fault or injury.
When using an AC adapter or external device, insert/remove the
connector straight to/from the terminal. Make sure the orientation of
the connector. Unless it's correct, it may cause overheating,
ignition, damage, or a fault.
CAUTION
Be sure to read the following cautions
before use.
Do not expose the camera lens to direct sunlight for an extended
period. Doing so might cause ignition, rupture, fire, or a fault by the
light-collecting mechanism of the lens.
Do not store or leave the product in places subject to direct sunlight
(e.g. in automobiles), places that get hot, places that get extremely
cold, and in humid or dusty places. Doing so might cause
overheating, ignition, deformation or a fault.
Do not leave or charge on unstable places such as rocky stands or
tilting surfaces. Dropping the product may cause injury or damage.
Also, pay sufficient attention to impact, etc. Doing so may cause a
fault or injury.
The product may become warm after use for long periods or after
being connected to an external power source. Do not touch the
product or specified charging equipment (sold separately) for long
periods. Doing so may cause low-temperature burns. Also do not
cover with paper, clothing, bedding, etc. Doing so may cause fire,
injury, or a fault.
When charging the product, do not exceed the ratings for outlets or
wiring equipment. Exceeding the ratings for power bars, etc. may
cause overheating resulting in fire.
-14-
■au Nano IC Card 04 LE
CAUTION
Be sure to read the following cautions
before use.
Be careful when attaching/removing the au Nano IC Card 04 LE.
Doing so might injure your hands or fingers.
Do not damage the au Nano IC Card 04 LE (use in high
temperatures, dispose of in fire, allow foreign objects to contact the
metal portion, subject to shock, bend or place heavy objects on it,
expose to wetting, etc.). Doing so may cause erasure of data or a
fault.
Do not store or leave the au Nano IC Card 04 LE where exposed to
direct sunlight or high temperatures or in a dusty place. Doing so
may cause a fault.
Store the au Nano IC Card 04 LE out of reach of small children.
Failure to do so might cause injury, etc. if they accidentally swallow
and choke on it.
-1-
When Using the Product
Before using the product, be sure to read the "Safety Precautions" in this
manual for proper usage.
Before you assume that the product is malfunctioning, check for possible
remedies in the following au Customer Support site of au homepage:
http://www.au.kddi.com/english/support/
•During communication, maintain a 1.5-cm separation from yourself with no
metal (parts) located in between.
•Communication is not possible even inside the service area in places where
the signal does not reach (e.g. tunnels and basements). Also,
communication is sometimes not possible in poor reception areas.
Communication is sometimes interrupted if you move into a poor reception
areas during communications.
•Since this product uses radio waves, the possibility of communication
interception by third parties cannot be eliminated. (Although, the 4G (LTE/
WiMAX 2+) system has highly secure confidential communication features.)
•This Product is designed for use in Japan only and cannot be used in any
other country.
•Since this product is a radio station under the Radio Law, you may be asked
to temporarily submit the product for inspection in accordance with the
Radio Law.
•IMEI information of the product is automatically sent to KDDI CORPORATION
for maintenance and monitoring operational status of the product.
•The Company is not liable for any damages arising from earthquakes,
lightning, storms, floods or other natural disasters, as well as fires, actions
by third parties, other accidents, intentional or mistaken misoperation by the
customer, or use under other unusual conditions outside the responsibility of
the Company.
•The Company is not liable for any incidental damages (change/
disappearance of described content, loss of business income, disruption of
business, etc.) arising from use or inability to use the product.
•The Company is not liable for any damages arising from failure to observe
the described content of this manual.
•The Company is not liable for any damages arising, for example, from
malfunction caused by combination with connected devices or software not
related to the Company.
-8-
Do not place near corrosive chemicals or in places where corrosive
gas is generated. Doing so might cause a fault or loss of internal
data.
Do not use if there is smoke, abnormal odor or noise, excessive
overheating, or other abnormalities. If an abnormality occurs,
disconnect the specified charging equipment (sold separately)
from the power outlet if you are charging the battery, make sure that
the product is not overheating before turning the power off, and
contact an au shop or Keitai Guarantee Service Center. Also, if you
have dropped or damaged the product, do not continue to use it in
that state, and contact an au shop or Keitai Guarantee Service
Center.
When inserting an earphone, etc. into the product, raise the volume
slowly to adjust the volume to the proper level. Sound suddenly at a
loud volume when first turned on, setting too loud a volume, or
using the earphone continuously for a long period of time might
adversely affect your ears. Also, raising the volume too high might
prevent you from hearing sounds around you, which might in turn
lead to a traffic accident at a railroad crossing or pedestrian
crossing.
■Main unit
DANGER
Be sure to read the following hazards
before use.
Do not puncture the product with a nail, hit with a hammer or step
on the product. Doing so might cause fire or damage.
Be careful not to have the product bitten by your pet. It might cause
leakage, overheating, rupture, ignition of the internal battery, fire or
injury.
-15-
■Use near medical equipment and in medical institutions
WARNING
Be sure to read the following warnings
before use.
When using the product near an implanted pacemaker, implanted
cardioverter-defibrillator or other electronic medical device, radio
waves might affect these units and devices. So, please observe the
following.
1. Those with an implanted pacemaker or implanted cardioverter-
defibrillator should carry or use the product at least 15 cm away
from the pacemaker or cardioverter-defibrillator.
2. Turn the product off or set "Airplane mode" when it may be
difficult to keep at least 15 cm away such as in a situation you
cannot move freely, since there may be people with a cardiac
pacemaker or implanted cardioverter-defibrillator nearby.
3. When a medical institution has laid down designated areas
where use of the product is prohibited or is not allowed to be
brought in, abide by the instructions of that medical institution.
4. When using electronic medical devices other than an implanted
pacemaker and implanted cardioverter-defibrillator outside a
medical institution (e.g. home medical treatment), check
individually with the manufacturer of the electronic medical
device regarding the influence of radio waves.
-2-
•Captured image data or downloaded data may sometimes be altered or lost
due to faults, repair or other handling of the product. The Company is not
liable for any damage or lost income resulting from recovery of these data.
•It is recommended you keep a copy of important data in your PC's hard disk,
etc. Whatever the cause of fault or malfunction may be, the Company
assumes no responsibility for alteration or loss of saved information.
•Contents saved in the product, such as contacts, mails and favorites, might
be altered or lost in an accident, fault, repair or mishandling. Be sure to keep
a copy of important contents. Note that Company assumes no responsibility
for any damages or lost profits resulting from altered or lost contents.
•Note that content data (both charged or free content) saved with the product
cannot be returned to the customer when the product is replaced for repair
of a fault, for example.
•The product uses liquid crystal for its display. The display response speed
may become slow when the ambient temperature is low, which is due to the
property of liquid crystal and not a malfunction. Display response speed will
return to normal at room temperature.
•Although the display used on the product is made using high-precision
technology, some pixels (dots) might be lit or out at all times. This is not a
malfunction.
•You are recommended to store copies of individual data such as photos you
took, videos and music on your PC by sending each file as mail attachment,
etc. Note, however, that you may not be able to make copies of any
copyrighted data even by the above-mentioned means.
•Do not discard the product together with regular trash. Please cooperate in
the collection of the product when it is no longer needed to protect the
environment and effectively use resources. Old product is collected at au
shops and other places.
* "The Company" as appears in this manual refers to the following companies:
Sold by: KDDI CORPORATION, OKINAWA CELLULAR TELEPHONE COMPANY
Manufactured by: KYOCERA Corporation
■Note
•Reproduction of the content of this manual in part or in whole is prohibited.
•The content of this manual is subject to change without notice.
•Every effort has been made in the preparation of this manual. Should
you notice any unclear points, omissions, etc., feel free to contact us.
-9-
WARNING
Be sure to read the following warnings
before use.
Turn off the product or put it in Airplane mode before boarding an
airplane. Use of terminals on board is restricted. Follow the
instructions of each airline.
Failure to do so may adversely affect on-board electronic
equipment. Prohibited acts related to terminal usage on an airplane
may be punished by law.
When using in hospitals, follow the guidelines of each institution.
Turn power off where use is prohibited.
Use may affect electronic equipment and electric medical
equipment.
Sometimes, very rarely some people demonstrate symptoms such
as temporary muscle spasms, loss of consciousness, etc. by
watching repeatedly flickering screens. Those with a past history of
this should consult with a physician beforehand.
Chemical hardened glass is used for the display of the product. In
case it is broken, do not touch the broken part. Doing so might
cause injury by the broken part. Contact an au shop or Keitai
Guarantee Service Center.
CAUTION
Be sure to read the following cautions
before use.
Use of the main unit in an automobile sometimes affects on-vehicle
electronic devices, though this rarely happens. If this happens,
stop use since this may impair safe travel.
If you feel any abnormality with your skin, immediately consult a
dermatologist. Itching, rashes, eczema, etc. sometimes occurs
depending on your physical constitution and condition.
The materials of parts used on the product are as follows.
-16-
Handling Precautions
Observing the following will prevent product faults and ensure adequate
product performance.
Be sure to read for proper use.
■Precautions common to the main unit, internal battery, charging
equipment, au Nano IC Card 04 LE, peripheral devices
●Do not apply excessive force to the product during use. Be sure not to put
the product into a tightly packed bag or place a heavy object on the
product in a bag. Doing so might damage the display or internal circuit
board resulting in a malfunction.
Keeping an external device connected to the external connection terminal
or earphone microphone terminal might damage the connector resulting in
a malfunction. Such damage and malfunction are not covered by the
warranty, even if there is no external damage.
●To ensure waterproof property (equivalent to IPX5 and IPX7) of this product,
use the product with the card slot cover attached securely for use.
Note that the waterproof property is not guaranteed in every usage
condition. Do not allow water to get inside the product or splash water on
the charging equipment or optional accessories. Do not open/close the
card slot cover in the rain or with waterdrops on the surface of the product.
Doing so might cause water intrusion resulting in internal corrosion.
Malfunctions determined to be caused by water intrusion are not covered
by the warranty.
●Do not use the product in extremely hot, cold or humid places. (Use within
an ambient temperature range of 5ºC to 35ºC and humidity range of 35% to
85%.)
-Charging equipment
-Peripheral devices
●Do not use the product in extremely hot, cold or humid places. (Use within
an ambient temperature range of 5ºC to 35ºC and humidity range of 35% to
90%. Temporary use at 36ºC to 40ºC is allowed.)
-Main unit
-au Nano IC Card 04 LE (attached to the main unit)
●Do not use in places subject to lots of dust or vibration.
-3-
Safety Precautions (Observe Strictly)
■Before using this product, thoroughly read these safety
precautions for proper use. After reading, store the precautions
in a safe place.
●These "Safety Precautions" describe instructions that should be observed to
prevent damage to property or injury to the customer or others using the
product.
●When the product is used by a child, parents or guardians should
thoroughly read the "Basic Manual" and teach the child how to use it.
●These instructions are divided into the following categories.
■Explanation of indications used in this manual
DANGER
This symbol indicates the potential and imminent
danger of death or serious injury (*1) to a person due
to mistaken handling.
WARNING
This symbol indicates the possibility of death or
serious injury (*1) to a person due to mistaken
handling.
CAUTION
This symbol indicates the possibility of personal
minor injury (*2) to a person or physical damage (*3)
due to mistaken handling.
*1 Serious injury: This refers to loss of sight, injury, burns (high- and low-temperature),
electric shock, broken bones, injuries with residual aftereffects from
poisoning, etc., and injuries requiring hospital admission for
treatment or long term hospital attendance as an outpatient.
*2 Minor injury: This refers to injuries, burns (high- and low-temperature), electric
shock, etc. that do not require hospital admission for treatment or
long-term hospital attendance as an outpatient.
*3 Physical damage: This refers to extended damage to buildings, furniture, livestock,
or pets.
-10-
■Qua tab 01 main unit
Part Material Surface treatment
Exterior case PC resin + GF
resin
Acrylic UV hard coating
(white, pink), cured urethane
coating (navy)
Display Hardened glass Chemical hardening
Power button,
Exterior panel
(edge around entire
unit)
PC resin Acrylic cured coating + acrylic
UV hard coating (white, pink),
metal vapor deposition + acrylic
UV hard coating (navy)
Volume UP/DOWN
button
PC resin Acrylic UV hard coating
Camera lens PMMA resin Chemical hardening
Camera lens ring Aluminum alloy Anodizing
Card slot cover PC + GF resin/
TPE resin
Acrylic UV hard coating
(white, pink), cured urethane
coating (navy)
Do not bring the product close to magnetized objects such as cash
cards, floppy disks, credit cards, and prepaid cards. Doing so
might result in loss of recorded information.
Do not allow liquids, metal objects, burnable items, and other
foreign matter to get inside the earphone microphone terminal, the
external connection terminal, the microSD memory card slot or the
au Nano IC Card 04 LE slot. Failure to do so might cause fire,
electric shock, a fault, or injury.
Use the product with the card slot cover, etc. closed. If the cover is
open, dirt or water may get inside causing a fault.
Be cautious with magnetic portions of product. Speaker and other
components use magnets, and may attract tacks, pins, cutter
blades, staples, or anything else metal, and cause unexpected
injury. Before using, always check that there are no foreign objects
on the speaker or other components.
-17-
●Clean the external connection terminal and earphone microphone terminal
with dry cotton swabs, etc. every now and then. Soiled terminals might
cause poor connection. Do not exert a strong force to clean either terminal
to prevent deformation.
●Clean with a dry, soft cloth (cloth for cleaning glasses, etc.). Rubbing
forcefully with a dry cloth may scratch the display. Water or other soiling on
display can stain the display if left uncleaned. Using organic solvents such
as alcohol, thinner, benzine, etc. may erase exterior print or fade color.
●Use as far away as possible from land-line phones, TVs and radios. Use
nearby might affect them.
●The product may become warm while charging or during other operations,
depending on the situation, but this is not abnormal.
●Do not put stickers on the product. Sound may not be emitted.
■Main unit
●Do not forcefully press, tap or intentionally subject the display to strong
impact. Doing so might cause scratching or damage.
●Do not forcefully press your fingernails, sharp objects or hard objects
against buttons or display surface. Doing so might cause scratching or
damage.
The touch panel is designed to be lightly touched by fingers. Do not apply
strong pressure with your fingers or sharp-pointed objects (such as
fingernails, ballpoint pens and pins) on the touch panel.
Touching the panel may not work in the following cases. Note that it may
cause malfunction.
•Operation with fingernails
•Operation with foreign object on the screen
•Operation with protective sheet or seal on the screen
•Operation with a water drops or dew condensation attached on the touch
panel
•Operation under water
●Do not remove the sticker appearing after opening the card slot cover and
imprinted with the IMEI.
-4-
■Explanation of graphic symbols used in this manual
Indicates an action that
is not allowed.
Indicates that use in a
place where the product
is likely to get wet or
allowing the product to
get wet is not allowed.
Indicates that handling
with wet hands is not
allowed.
Indicates an action that
must be done.
Indicates that
disassembly is not
allowed.
Indicates that the power
plug must be
disconnected from the
power outlet.
■Precautions common to the main unit, internal battery,
charging equipment, au Nano IC Card 04 LE, peripheral
devices
DANGER
Be sure to read the following hazards
before use.
Be sure to use only the specified peripheral devices. Use of other
devices might cause overheating, ignition, rupture, fault, or leakage
of liquid.
Do not use, store or leave the product in hot places (e.g. by the fire,
near a heater, under a kotatsu, in direct sunlight, in a car in the hot
sun). Doing so might cause ignition, rupture, fault, fire or injury.
Do not put the product in a cooking apparatus such as microwave
oven or a pressure vessel. Doing so might cause ignition, rupture,
fault, fire or injury.
-11-
Do not place the product directly on sand at a beach, etc. Sand or
other small particles might get inside the microphone, speaker, etc.
causing the volume to drop. If sand gets inside the product, it might
cause overheating or a fault.
■Internal battery
(The internal battery of this product is a lithium-ion
battery)
The internal battery is not fully charged at the time of
purchase. Also charge after not using the product for a
long period.
DANGER
Be sure to read the following hazards
before use.
If the leaked liquid gets on your skin or clothes, immediately rinse it
off with water to avoid injury. If the liquid gets into your eyes, do not
rub, but after wash your eyes with water, and immediately consult a
doctor to avoid the risk of losing your eyesight. If the liquid gets on
a device, wipe it off without touching it.
The internal battery is a consumable item. If the performance of the
internal battery does not recover (e.g. the usable time after each
charge has become extremely short), the battery is at the end of
service life, so stop use. Failure to do so might cause overheating,
ignition, rupture or leakage. Since the battery is built into the
product, we keep your product and replace the battery for a fee.
You may not use the product for a certain period. The life time of
the internal battery depends on the usage etc.
-18-
●Never use modified au terminals. Use of a modified device violates the
Radio Law.
This product has acquired the certification of conformity with technical
regulations for the specified radio station based on the Radio Law, and the
"Technical Conformity Mark " is checkable on au terminals as a
certificate.
Home screen →[Settings] →[About tablet] →[Compliance information]
If the product is disassembled and modifications are made to the internal
components, the certification of conformity with technical regulations will
become invalid. Do not use the product with the certification invalid, as it is
a violation of the Radio Law.
●Take care not to place magnetized items such as magnetic cards, speakers
and TV sets near the product, as it might cause malfunction. Putting a
strong magnetism close to the product might cause false operation.
●When you put the product in your bag, etc., take care so that the display
does not come in contact with metal objects or other hard objects. Doing
so might cause scratching or damage.
●When suddenly brought into a warm place from a cold place, or when in a
humid location, or when used where temperature suddenly changes (e.g.
near the air discharge port of an air conditioner), water droplets (i.e.
condensation) sometimes are formed inside the product. Note that when
used under conditions such as this, the humidity might cause corrosion or
a fault.
●When wiping the display, wipe with a soft, dry cloth. Use of a moistened
cloth, glass cleaner or other similar liquid might cause a fault.
●When connecting/disconnecting the external device to/from the external
connection terminal or the earphone microphone terminal, make sure that
the connector or plug of external device is straight with the external
connection terminal.
●Note that applying unnecessary force with the external connection terminal
or the earphone microphone terminal connected to the external device
might cause damage.
●Do not exert excessive force when attaching/removing a microSD memory
card. Doing so might injure your hands or fingers.
●While writing/reading data to/from a microSD memory card, do not subject
the product to vibration or impact, or turn off the power. Doing so might
cause loss of data or malfunction.
-5-
Do not throw the product into a fire or heat it. Doing so might cause
ignition, rupture or fire.
The customer is not allowed to disassemble, modify or repair the
product. Doing so might cause a fault, ignition, electric shock, or
injury. The Company is not liable even in the event of any
nonconformities arising on the product or peripheral devices as a
result of modification, etc. Modification of the product is in violation
of the Wireless Telegraphy Act.
The product's battery is built in, and cannot be replaced by the
customer. For battery replacement, contact an au shop or Customer
Service Center.
WARNING
Be sure to read the following warnings
before use.
Before entering an area where flammable gas is generated such as
a gas station, always be sure to turn off the product, and
discontinue charging the product if charging. Failure to observe
these precautions might cause the gas to catch fire.
When using a metal accessory etc., make sure not to allow the
metal part come in contact with the connection terminal, earphone
microphone terminal or power outlet. Doing so might cause electric
shock, ignition, injury or a fault.
Do not drop or subject to strong impact, such as throwing. Doing
so might cause rupture, overheating, ignition, or a fault.
Do not use outside when you can hear thunder. Doing so might risk
lightning strikes and electric shock.
-12-
■Charging equipment
WARNING
Be sure to read the following warnings
before use.
Do not use at other voltages than the specified power supply
voltage. Doing so might cause ignition, fire, overheating, or electric
shock.
•AC adapter (sold separately): 100 VAC to 240 VAC
Insert the power plug on the specified charging equipment (sold
separately) all the way into the outlet. Not being plugged in all the
way may cause electric shock, overheating, ignition, fire, or injury.
Do not use if the specified charging equipment (sold separately) is
damaged or the outlet receptacle is loose.
Do not damage, rework, twist, pull, or place heavy objects on the
cable of the specified charging equipment (sold separately). Do
not use a damaged cable. Doing so may cause electric shock,
short-circuiting, fire, or injury.
Do not touch the specified charging equipment (sold separately) if
thunder is audible. Doing so may cause electric shock due to
lightning.
Before cleaning, unplug the specified charging equipment (sold
separately) from its outlet. Cleaning while plugged in may cause
electric shock or short-circuiting.
Wipe off dust on the power plug. Failure to do so might cause fire,
burns or electric shock.
When the specified charging equipment (sold separately) is not to
be used for a long time, disconnect the power plug from the power
outlet. Doing so might cause fire or a fault.
-6-
To avoid short-circuiting the connection terminal or earphone
microphone terminal, do not allow fingers or other part of your body
or conductive foreign objects (metal fragments, pencil leads, etc.)
to come into contact with or get inside the connection terminal or
earphone microphone terminal. Doing so might cause overheating,
fire, a fault, electric shock, or burns.
If the product is damaged because it is dropped or something, and
its display is cracked or internal parts are exposed, do not touch
the cracked display or exposed parts with your hands. Doing so
might cause electric shock or injury from damaged parts.
If the wet product is charged, electric shock, short circuit, or
corrosion may occur and overheating may cause fire, malfunction
or burns.
Although this product model has waterproof property, stop use if
liquid such as water gets inside the product from the card slot
cover, etc., and contact an au shop or Keitai Guarantee Service
Center. Continued use of the product in this state might cause
overheating, ignition, fire, electric shock, or a fault.
Do not use while driving a car or riding a motorbike or bicycle or
while walking. It might cause a traffic accident or cause someone
to fall. Use while driving a car or motorbike is prohibited by law.
Use while riding a bicycle may be punishable by some regulations.
If charging is not completed after the specified charging time, stop
charging. Failure to do so might cause leakage of liquid,
overheating, rupture or ignition.
Do not leave in places within the reach of small children. Small
children might swallow small parts, etc. by mistake and choke on
them, or might drop them by mistake and cause accidents or injury.
-13-
Do not use in places subject to direct splashing with water, pet
urine or other liquids. Doing so might result in faults resulting from
overheating, fire, electric shock, short-circuiting of electronic
circuits, or injury. In the event that the product is splashed with
liquid, immediately disconnect power plug of the specified
charging equipment (sold separately).
Do not leave specified charging equipment (sold separately)
plugged in if not in use. Do not wrap cord of specified charging
equipment (sold separately) around adapter body. Doing so may
cause electric shock, overheating, fire, a fault, or injury.
Do not forcibly bend the charging equipment's plug or the
connection between the connector and power cord. Doing so might
cause electric shock, overheating, fire, fault or injury.
CAUTION
Be sure to read the following cautions
before use.
Do not use in humid places such as bath areas, or connect/
disconnect the specified charging equipment (sold separately) with
wet hands. Doing so might cause electric shock, a fault or injury.
When unplugging the specified charging equipment (sold
separately) from its outlet, hold by the plug. Pulling by the cable
may damage the cable.
-19-
●Do not cover the sensor with your finger or put a sticker on it. Doing so may
hinder the sensor for detecting the ambient light level and functioning
correctly.
■Touch panel
●Use your finger to operate the touch panel. Do not use ballpoint pens,
pencils or other sharp-pointed objects. Using such objects does not only
hinder correct operation of the touch panel, but also might cause
scratching or damage to the display.
●Adhering stickers and protectors (commercially-available protective films,
privacy protectors, etc.) on the display may prevent the touch panel from
operating correctly.
●If the display surface is dirty, it may not function correctly. In such case,
wipe the display surface with a dry, soft cloth.
●When carrying the product in your bag, etc., take care not to put the touch
panel close to metals or other conductive materials, as it might cause false
operation of the touch panel.
■Internal battery
●Use in very hot or cold environments, for example, when left in an
automobile with the windows closed in summer, will cause the internal
battery capacity to drop and shorten the available battery usage time. This
will also shorten the internal battery's service life. Try to use the product as
far as possible at room temperature.
●After the internal battery is charged, battery power decreases bit by bit
even if the product is not used. The internal battery may be discharged if
the product is not used for a long time. We recommend to charge the
product before use.
■au Nano IC Card 04 LE
●Do not forcibly remove or insert the au Nano IC Card 04 LE. Be careful not
to exert excessive force when inserting the card into your au terminal.
●You are responsible for any malfunction caused by inserting your au Nano
IC Card 04 LE into another IC card reader, etc.
●Keep the IC (metal) part of your au Nano IC Card 04 LE clean. Wipe the
card with a dry, soft cloth (such as for cleaning eyeglasses) for cleaning.
●Do not put stickers, etc. on the au Nano IC Card 04 LE.
-20-
■Camera
●When using the camera, follow common rules of etiquette regarding camera
use.
●When photographing important occasions (such as a wedding), take a trial
shot and check the shot image to make sure it is correctly shot.
●Do not use the camera for recording commercially available books or
information of which photographing is not allowed.
●Performance may not be obtainable in low-temperature conditions,
including the camera not activating.
■Copyrights and rights of portrait
●You are not allowed to copy, distribute, publish, modify or edit the data you
shot, recorded or downloaded using this product without the consent of the
copyright holder, except for personal use, under the copyright law.
In addition, do not use or modify portraits or names of other individuals
without their consent, as it might infringe on rights of portrait.
Note that shooting and recording may be restricted at some live
performances, shows and exhibitions even for personal use.
●Be careful about the copyright and portrait right when posting photos you
shot, etc. on Internet homepages.
■Backup content on the product
●Please back up important content registered to the product or downloaded
for the product from an outside source. Content recorded to memory on the
product sometimes disappears or is altered by unexpected factors, such
as static electricity or a fault, repair, mishandling, etc.

-21-
Available Security Codes
The product has various security codes that you can use.
The available security codes are as follows. Do not forget the various security
codes that are set as they are necessary for various operations and contracts.
Be sure to change initial codes to your own codes before using the product.
■Security code
Example of
usage
To make inquiries, applications, and changes on the au
homepage
Initial value A four digit number chosen by the customer and noted on the
application form
■Setting the security type for the start screen
Example of
usage
To disable security
Initial value Swipe
■PIN code
Example of
usage
To prevent unauthorized use of the au Nano IC Card 04 LE by
third parties
Initial value 1234
Be sure to change initial codes to your own codes before using the product.
-28-
If any liquid other than plain water gets on the product
If any liquid other than plain water (e.g. seawater, detergent, alcohol) gets on
the product, immediately rinse it with plain water.
You can wash the product under a mild flow (up to 6 liters per minute) of tap
water at room temperature (5ºC to 35ºC) at a distance of about 10 cm from the
faucet or showerhead.
If the product gets dirty, do not use a brush and wash it with your hands
holding the card slot cover so that it does not open.
After the product gets wet
After the product gets wet, drain water, and wipe the main unit with a clean dry
cloth.
In cold climates, water on the product may turn to frost. Using the product with
frost may cause a fault. Do not leave the product without wiping off the water.
(No special measures against condensation have been implemented in this
product.)
Rubber seals
The rubber seal around the card slot cover is important to maintain waterproof/
dustproof properties. Do not damage or remove the rubber seal.
When closing the card slot cover, take care not to get the rubber seal caught.
Forcibly closing the cover with the rubber seal caught may damage it resulting
in loss of waterproof/dustproof properties. Just a small particle (a single hair,
etc.) on the seal can cause water or dust intrusion.
If any chemical liquid (detergent, alcohol, etc.) gets on the rubber seal, it may
cause deterioration in durability.
Do not insert sharp objects into gaps around the card slot cover. Doing so
might damage or deform the product or damage the rubber seal, causing
water leak.
It is recommended to replace the parts for maintaining waterproof/dustproof
properties once every two years regardless of whether any abnormality is
present. For information on part replacement, contact an au shop near you.
Charging
Never charge the battery if the product is wet.
Optional accessories are not waterproof/dustproof.
-35-
Cautions on Using the 5 GHz Band
Wireless LAN (Wi-Fi®) function of this product uses 5 GHz band. Using the 5.2
GHz band and 5.3 GHz band outdoors is prohibited by the Radio Law.
The channels used on the product are as follows.
W52 (5.2 GHz band/36, 38, 40, 42, 44, 46, 48 ch)
W53 (5.3 GHz band/52, 54, 56, 58, 60, 62, 64 ch)
W56 (5.6 GHz band/100, 102, 104, 106, 108, 110, 112, 116, 118, 120, 122,
124, 126, 128, 132, 134, 136, 140 ch)
Notes on Packet Communication Charges
•Since constant Internet connection is possible with the product, packet
communication may be performed automatically by some applications,
resulting in high packet communication charges. Therefore, subscription to a
packet flat-rate service/packet communication charge discount service is
recommended.
•To browse homepages, download applications, communicate using
applications, send/receive e-mails and configure various settings with the
product, connection to the Internet is required, to which packet
communication charge applies.
* Packet communication charges are not incurred for Wireless LAN (Wi-Fi®) use.
-22-
PIN Code
■PIN code
To prevent unauthorized use of the au Nano IC Card 04 LE by a third party,
you can set the product to require PIN code entry every time the power is
turned on. You also need to enter the PIN code when setting whether PIN
code entry is required.
If the PIN code is incorrectly entered three times consecutively, the PIN code
will be locked. You can unlock the PIN code using the PUK code.
•The PIN code is "1234" and PIN code entry was set to not be required at the
time of purchase. You can change the PIN code to any four- to eight-digit
number, and set PIN code entry to be required as necessary.
If you require a PIN code to be entered, make sure to change the number to
your own unique number.
■PUK code
In case the PIN code is locked, you can unlock it by entering the PUK code.
•The PUK code is an eight-digit number assigned at the time of purchase,
which is printed on the back side of the plastic card on which your au Nano
IC Card 04 LE is attached.
•After entering the PUK code, you need to set a new PIN code.
•If the PUK code is incorrectly entered ten times consecutively, contact an au
shop, PiPit or Customer Service Center.
•The PIN code is not reset by initializing the product.
-29-
Water resistance
The product is not designed to resist water pressure, and should not be used
where exposed to high water pressure (tap, shower, etc.) or be held under
water for an extended period. Avoid directly exposing to strong waterflow
exceeding the rating (6 liters per minute or more waterflow: for example,
strong waterflow from a tap or shower that is painful on the skin). The product
is rated with IPX5 water resistance, however, such exposure may cause
malfunction. Do not wash in a washer, ultrasonic washer, etc.
The product does not float.
Heat resistance
Do not use in hot water, in a sauna, or with hot air (hairdryer, etc.). The product
is not designed to resist heat.
Shock resistance
The product is not shock resistant. Do not drop or subject to shock. Do not
poke the speaker, etc. with a cotton swab or pointed object. Doing so might
damage/deform the main unit, and allow water and dust intrusion.
■Draining water after wetting the product
As some parts of this product are not watertight, if you use the product after it
gets wet, water remaining in those parts might wet your clothes or bag, or the
sound might become hard to hear.
Follow the steps below to drain water.
󱫀Wipe water thoroughly on the
surface of the product with a
clean dry cloth without waste
textiles.
-36-
Notes on Applications
•Be sure to check the security of the application, then install it at your own
risk. Some applications might cause virus infection, damage various data,
and send out your location information, usage history or personal information
stored in the product via the Internet.
•The Company assumes no responsibility for any trouble with applications,
etc. which the customer has installed. In this event, the customer may be
charged for repairs even if within the warranty period.
•The Company assumes no responsibility for any disadvantage brought to
you or any third party by applications you have installed.
•Some applications require that a microSD memory card be inserted.
•Some applications prohibit the product from entering sleep mode while they
are active, or rapidly drain the battery while running in the background.
•Changes to method of operation or to screen display may occur without
notice due to version upgrades of applications pre-installed on the product
or that were installed later. Note that there may be differences with
descriptions in this manual.
Specific Absorption Rate of This Data
Communication Terminal
This model Qua tab 01 data communication terminal complies with Japanese
technical regulations and international guidelines regarding exposure to radio
waves.
This data communication terminal has been designed in observance of the
Japanese technical regulations regarding exposure to radio waves(*) and limits
to exposure to radio waves recommended by equivalent international
guidelines. These international guidelines were set out by the International
Commission on Non-Ionizing Radiation Protection (ICNIRP), which is in
collaboration with the World Health Organization (WHO), and the permissible
limits include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health condition.
-23-
Notes on Waterproof and Dustproof
Properties
This product has a waterproof property equivalent to IPX5*1 and IPX7*2, as well
as a dustproof property equivalent to IP5X*3 on the condition that the card slot
cover is securely attached.
*1 IPX5 equivalent means that the product will maintain its operability as a
communication terminal even if it is sprayed with water from a 6.3 mm diameter
nozzle at a distance of about 3 meters for more than 3 minutes at a rate of about
12.5 liters per minute from any direction.
*2 IPX7 equivalent means that the product will maintain its operability as a
communication terminal with no water getting inside the main unit even if it is
gently submerged in a tank of still tap water at room temperature to a depth of 1
meter for about 30 minutes.
*3 IP5X equivalent means that the product functions as and safely maintains
functioning as a communication terminal even after it has been placed in an
apparatus with grit and dust of diameters of 75 μm or less and shaken for 8
hours.
Before using the product, thoroughly read "Important Items to Remember
before Use" and "Tips for Comfortable Use" to ensure correct use. Failure to
follow the contents described in these sections may cause the intrusion of
water, sand or other foreign material, resulting in overheating, ignition, electric
shock, injury or a fault.
Since operation of the product on each usage scene was confirmed based on
the above assumption, proper operation of the product in every possible
condition during actual use is not guaranteed. Malfunctions determined to be
caused by mishandling by the customer are not covered by the warranty.
-30-
󱫂Shaking the product
①Hold the product firmly and shake it in the direction of arrows until
water does not come out.
* When shaking the product, stay alert to your surroundings.
* Be careful not to have the product pop out, and hold it firmly to drain water.
Earphone microphone terminal end:
20 times or more
External connection terminal end:
20 times or more
②Wipe drained water.
* The microphone, the speaker, external connection terminal area, and
earphone microphone terminal area are particularly hard to drain. Face
those parts down and press to wipe off.
③Place the product on a dry towel or cloth and leave it at room
temperature.
󱫄Press the product gently to a
lint-free, clean, dry cloth, and
wipe off water remaining in
the gaps in the microphone,
speaker, external connection
terminal area, earphone
microphone terminal area, etc.
󱫆Leave the product for one hour or more at room
temperature to dry after removing drained water
thoroughly.
Even after you take these procedures, water may remain on the product. Do not
place the product near things that you do not want to wet.
Also, take care not to wet your clothes, bag, etc.
-37-
The Japanese technical regulations and international guidelines define the
limits using a unit of measurement known as the Specific Absorption Rate
(SAR), which represents the average amount of radio frequency energy
absorbed by the human body. The SAR limit for this data communication
terminal is 2.0W/kg. The highest SAR value for this data communication
terminal when tested for ordinary use as described in this manual is 0.560W/kg.
The actual SAR of this data communication terminal while talking on the phone
can be well below that indicated above.
This is due to automatic changes in the power level of the data communication
terminal to ensure it only outputs the minimum power required to communicate
with a base station. Therefore in general, the closer you are to a base station,
the lower the power output of the data communication terminal.
During communication, hold the product at least 1.5 cm away from your body
and also do not allow metal parts between the product and your body. By
doing this, this data communication terminal complies with Japanese technical
regulations and international guidelines regarding exposure to radio waves.
The World Health Organization has stated that present scientific information
does not indicate the use of mobile devices has any harmful effects on the
human body. They recommend that if you are still worried about your exposure
then you can limit your talk time or use a handsfree kit to keep the mobile
phone away from your head and body.
If you would like to know more detailed information, please refer to the WHO
website.
( http://www.who.int/docstore/peh-emf/publications/facts_press/fact_english.htm )
Please refer to the websites listed below if you would like to know more
detailed information regarding SAR.
○Ministry of Internal Affairs and Communications website
(http://www.tele.soumu.go.jp/e/sys/ele/index.htm)
○Association of Radio Industries and Businesses website
(http://www.arib-emf.org/01denpa/denpa02-02.html)(in Japanese only)
○au homepage:
(http://www.au.kddi.com/english)
* Technical regulations are defined by the Ministerial Ordinance Related to Radio Law
(Article 14-2 of Radio Equipment Regulations).
-24-
Important Items to Remember before Use
●Make sure that the card slot cover is firmly closed.
•Waterproofness/dustproofness is only effective when the covers are
securely closed.
•Not doing so may allow minute particles (a single hair, etc.) to become
lodged between contact surfaces and allow intrusion of water.
•Do not open/close the card slot cover if the product or your hands are
wet. Do not insert earphones if water remains in the earphone microphone
terminal.
•Do not immerse in water with earphone connected.
Card slot cover
-31-
■Precautions on charging
The optional accessories are not waterproof/dustproof. Be sure to check the
following points before and after charging.
•Never charge the battery if the product is wet. Doing so might cause electric
shock or short circuit resulting in a fire, a fault or burns.
•Check that the main unit is not wet. If you are charging the battery just after
the product gets wet, drain water well and wipe the remaining water off with
a clean dry cloth before connecting the microUSB plug into the external
connection terminal.
•Do not touch the specified charging equipment (sold separately) with wet
hands. May cause electric shock.
•Use the specified charging equipment (sold separately) where it is not
exposed to water, and do not use in a bath room, shower room, kitchen, sink,
or other place where water is used. Doing so may cause a fire, electric
shock, a fault, or injury. When not charging, do not bring into a bath room.
Doing so may cause a fire, electric shock, a fault, or injury.
-38-
Intellectual Property Rights
■Trademarks
Company names and product names referred to in this manual are trademarks
or registered trademarks of respective companies.
Google and Google logo, Android and Android logo, Google Play and Google
Play logo, Play Music, Play Music logo, Play Movies, Play Movies logo, Gmail
and Gmail logo, Google Maps and Google Maps logo, Hangouts and
Hangouts logo, Google Maps Navigation and Google Maps Navigation logo,
Google Chrome, Google Chrome logo, Google Voice Search and Google
Voice Search logo, and YouTube and YouTube logo are trademarks or
registered trademarks of Google, Inc.
Microsoft®, Windows®and Windows Vista®/Windows®7/Windows®8/
Windows®8.1 are registered trademarks of Microsoft Corporation in the U.S.A.
and other countries.
The official name for Microsoft®Windows®is Microsoft®Windows®Operating
System.
Microsoft®, Microsoft®Excel®, Microsoft®PowerPoint®, Windows Media®, and
Exchange®are trademarks or registered trademarks of Microsoft Corporation
in the United States and other countries.
Microsoft®Word and Microsoft®Office are product name of Microsoft
Corporation in the United States.
QR code is a trademark of DENSO WAVE INCORPORATED.
microSD, microSDHC and microSDXC logos are trademarks of SD-3C, LLC.
-25-
How to close the card slot cover
Return hinge to inside the product, and then ①press entire cover with pad of
your finger. Press along cover in directions shown ②to close firmly ensuring there
are no gaps.
① ②
●Do not immerse the product in water with soap, detergent or bath salts in it.
●Do not immerse the product in seawater, a swimming pool or hot spring.
●Do not immerse the product in any liquid (alcohol, etc.) other than water.
●Do not place the product directly on the sand at a beach, etc. Sand or other
small particles might get inside the microphone, speaker, etc. causing the
volume to drop. If sand gets inside the product, it might cause overheating
or a fault.
●Do not leave the product where the temperature becomes high, such as in
direct sunlight on a beach.
●Do not use the product underwater.
●Do not leave the product in a humid place such as a bathroom or kitchen
for an extended period of time.
Soap/detergent/
bath salts
Seawater Swimming pool Hot spring Sand/mud
-32-
Notes on Using the Bluetooth®/Wireless
LAN (Wi-Fi®) Function
•The product's Bluetooth®function is for use within Japan. The product's
Bluetooth®function is certified as complying with Japanese domestic
wireless standards.
•The product's Wireless LAN (Wi-Fi®) function is for use within Japan. The
product's Wireless LAN (Wi-Fi®) function is certified as complying with
Japanese domestic wireless standards.
•The 2.4 GHz band used by Wireless LAN (Wi-Fi®) and Bluetooth®devices is
operated by various other devices. For this reason, the communication
speed and connectable range may be decreased, or disconnection may
occur, due to interference from other devices.
•Do not use this product in places where electromagnetic waves are
generated or near electric products, AV and OA equipment, or other
magnetized devices.
•Subjecting this product to magnetic or electrical noise might increase noise
and prevent it from performing communications. (This product is particularly
susceptible to noise when it used near a microwave oven.)
•Using this product near a TV, radio or similar appliance might cause
reception interference and disrupt TV images.
•The searching might not be successful if there are multiple Wireless LAN
(Wi-Fi®) access points near to the product or the same channel is being
used.
•Use of terminals on board aircraft is restricted. Follow the instructions of
each airline.
•The communication speed and connectable range vary depending on the
distance between communication devices, obstacles and the devices used.
-39-
Bluetooth®and logo are registered trademarks owned by the Bluetooth SIG,
Inc., and KYOCERA Corporation is licensed to use those trademarks.
WiMAX is a trademark of WiMAX Forum.
Wi-Fi®, WPA®, Wi-Fi CERTIFIED logo and Wi-Fi Protected Setup logo are
registered trademarks of Wi-Fi Alliance.
Wi-Fi CERTIFIED™ and Wi-Fi Protected Setup are trademarks of Wi-Fi Alliance.
Facebook and Facebook logo are trademarks or registered trademarks of
Facebook, Inc.
Twitter and Twitter logo are trademarks of Twitter, Inc., and are used under
license.
iWnn of OMRON SOFTWARE Co., Ltd. is used for conversion methods for
Japanese language, and for phrase prediction methods for English.
iWnn IME©OMRON SOFTWARE Co., Ltd. 2009-2015 All Rights Reserved.
© 2014 Comic Communication Co., Ltd. All rights reserved.
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT
PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE
OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE
MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/OR (ii) DECODING
MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED
FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY
BE OBTAINED FROM MPEG LA, LLC. SEE ( HTTP://WWW.MPEGLA.COM.)
⑴ACCESS, the ACCESS logo, and NetFront are registered trademarks or
trademarks of ACCESS CO., LTD. in the United States, Japan and/or other
countries.
⑵This software is based in part on the work of the Independent JPEG Group.
The product includes pictograms licensed by NTT DOCOMO, INC.
All other company names and product names are trademarks or registered
trademarks of respective companies referred to in this manual.
-26-
Tips for Comfortable Use
●Once the product gets wet, water may remain in gaps on the product.
Shake the product well to drain water. Especially make sure to drain water
remaining in the external connection terminal and earphone microphone
terminal.
●Even after the water is drained, the inner parts might be still wet. Although
you can use the product, do not place it near things that must not get wet.
Take care not to wet your clothes, bag or contents of the bag.
●Drain water if it becomes temporarily hard to hear the sound due to water
remaining in the microphone, etc.
■Notes on various usage scenes
<In the rain>
You can hold and operate the product with wet hands in the rain without an
umbrella.
•The rain in this case means a moderately-heavy rain (less than 20 mm per
hour).
•Water drops on the display might cause errors in the touch panel operation.
•Never open/close the card slot cover if the product is exposed to rain, or
your hands are wet.
<In the shower>
You can hold and operate the product with wet hands after a shower.
•Avoid spraying the product with high-pressure water, as the product is not
designed to withstand high water pressure.
<Washing>
You can wash the product under a mild flow (up to 6 liters per minute) of tap
water at room temperature (5ºC to 35ºC) at a distance of about 10 cm from the
faucet or showerhead.
•Do not spray the product with high-pressure water or submerge it in water
for extended periods of time, as the product is not designed to withstand
high water pressure.
•Wash the product with your hands with the card slot cover held so that it
does not open. Do not use a brush or sponge.
•Do not wash the product in a washing machine or ultrasound bath.
-33-
Cautions on Using the 2.4 GHz Band
The frequencies used by the Bluetooth®and/or Wireless LAN (Wi-Fi®) function
of this product are in the 2.4 GHz band. In this frequency band, other similar
wireless stations, in-plant wireless stations for mobile unit identification that
require a license to use, such as factory production lines, specific small power
wireless stations that do not require licenses, amateur wireless stations
(collectively called "other wireless stations" from here on) are operated in
addition to home electrical appliances such as microwave ovens, devices for
industrial, scientific and medical devices.
1. Before using the product, make sure that "other wireless stations" are not in
operation nearby.
2. In the event that instances of radio wave interference have occurred
between the product and "other wireless stations", immediately either
relocate the product or stop operation of the device (stop the emission of
radio waves).
3. If you are unclear on any points or are troubled by anything, contact an au
shop or Customer Service Center.
•The connections between this product and all other Bluetooth®and Wireless
LAN (Wi-Fi®) devices have not been confirmed. Therefore, connections with
all Bluetooth®and Wireless LAN (Wi-Fi®) devices are not guaranteed.
•This product supports security features for wireless communications that are
compliant with the Bluetooth®and Wireless LAN (Wi-Fi®) standard
specifications, but the security may not be sufficient depending on the
usage environment and configuration.
Be careful when making data communication using Bluetooth®or Wireless
LAN function (Wi-Fi®).
•Wireless LAN (Wi-Fi®) has the advantage that it can be freely connected
anywhere within the radio wave range, as it uses radio waves for exchanging
information. At the same time, there is a risk that a malicious third party may
obtain unauthorized access if security settings have not been configured.
You are recommended to configure security settings before use at your
decision and responsibility.
•The Company assumes no responsibility for leakage of data or information
that may occur during Bluetooth®/Wireless LAN (Wi-Fi®) communication.
-40-
Users of the product are authorized to use software installed into the product
described in this manual. Pay attention to the following points when using the
software.
(a)The software installed on this product or part of it may not be altered,
delivered, modified, analyzed, reverse-engineered, derived, and any such
actions are prohibited.
(b)Illegally importing the software or a part of it is prohibited.
(c)This Software is provided without implied warranties of merchantability,
fitness for a particular purpose and noninfringement of third party rights.
Note that the existing license agreement takes priority for usage of GNU
General Public License (GPL), GNU Library/Lesser General Public License
(LGPL) included in software, software based on other open source software
license and software that KYOCERA Corporation is licensed.
For information on the Open source software, refer to "Open Source Software"
as follows;
■Open Source Software
Note that the existing license agreement takes priority for usage of GNU
General Public License (GPL), GNU Library/Lesser General Public License
(LGPL) included in software, software based on other open source software
license and software that KYOCERA Corporation is licensed. The exact terms
of GPL, LGPL and some other licenses are reproduced in "About tablet" in this
product. For details, refer to Kyocera homepage.
This product includes software copyrighted by KYOCERA Corporation and
licensed software.
Copyright of the software designed and developed complying with the open
source software standard belongs to KYOCERA Corporation or the third
parties, distribution, reproduction, transformation and transmission over public
lines without consent of KYOCERA Corporation are prohibited, unless you are
authorized or permitted by Copyright Law.
-27-
•Do not splash the product with or immerse it in soap water, detergent water,
etc. other than tap water.
<In the bath>
You can use the product in a bathroom.
•Although you can operate the product with wet hands, do not immerse the
product into a bathtub. The product is not resistant to hot temperatures.
•Do not use the product in a bathroom for an extended period of time. The
product is not moistureproof.
•Do not immerse the product in hot spring water, soap water, detergent water,
or water with bath salts in it. Also, do not use the product underwater. Doing
so might cause a fault.
•Extreme changes in temperature cause condensation. Wait until the product
reaches room temperature before you bring the product from a cold place
into a warm bathroom.
•If condensation occurs inside the display, leave the product at room
temperature for a while until the condensation is cleared.
•Do not splash the product with hot water. The product is not resistant to hot
temperatures.
<In a kitchen>
You can use the product in the kitchen and other places where water is used.
•Do not splash the product with or immerse it in soap water, detergent water,
seasonings, juices, etc. other than tap water.
•Do not immerse the product in or splash it with boiling water. The product is
not resistant to hot temperatures.
•Do not place the product where it gets extremely hot or cold such as near a
stove or in a refrigerator.
■Common precautions
Card slot cover
Make sure that the card slot cover is firmly closed. Just a small particle (a
single hair, etc.) on the seals can cause water or dust intrusion.
Do not open/close the card slot cover with gloved hands. Just a small particle
(a single hair, etc.) on the seals can cause water leak. Wipe off any minuscule
droplets of water or dirt with a clean dry cloth before closing the covers.
If the card slot cover is deteriorated or damaged, the waterproof/dustproof
properties become ineffective. In such case, contact an au shop near you.
-34-
•Since Bluetooth®and Wireless LAN (Wi-Fi®) functions use the same
frequency band, using the both functions at the same may cause radio wave
interference resulting in decreased communication speed or disconnection
from the network. If connection fails, stop using either of the Bluetooth®and
Wireless LAN (Wi-Fi®) functions.
Bluetooth®and Wireless LAN (Wi-Fi®) functions of this product use
frequencies in the 2.4 GHz band.
•Bluetooth®function: 2.4FH1/XX1
2.4FH1/XX1
This product uses the 2.4 GHz band. FH-SS is used as the modulation
scheme. The interference distance is about 10 m or less.
Bands of mobile unit identification devices cannot be avoided.
•Wireless LAN (Wi-Fi®) function: 2.4DS4/OF4
This product uses the 2.4 GHz band. DS-SS and OFDM are used as the
modulation schemes. The interference distance is about 40 m or less.
This means that all bandwidths are used, and that band of mobile unit
identification devices can be avoided.
Available channels vary depending on countries.
For use in an airplane, check with the airline company in advance.
-41-
■Export Administration Regulations
This product and its accessories may be subject to the Japan Export
Administration Regulations ("Foreign Exchange and Foreign Trade Law" and
its related laws).
In addition, U.S. Re-export Regulations (Export Administration Regulations
and the related laws and regulations), regulations in other countries may apply
to this product and its accessories. To export and re-export this product and
its accessories, directly or indirectly, take the required measures on your
responsibility and at your expenses. For details on the procedures, contact the
Ministry of Economy, Trade and Industry, the U.S. Department of Commerce,
or authority concerned.
■Recording of diagnostics and usage data
KYOCERA Corporation requests the cooperation of customers with the
improvement of product and service quality. Fault diagnostics and usage data
(customer's use of applications, error logs, detailed information on customer's
application use (specific functions, frequency of use, memory/battery use))
are recorded and stored in the customer's device, with the purpose of allowing
KYOCERA Corporation to track and handle diagnostic events including
unexpected shutdowns and system errors in order to improve quality and
service. This information may be collected with the customer's permission
when device repairs are requested.
Refer to the "取扱説明書 詳細版 (Full Instruction Manual)" (Japanese) or
"Instruction Manual application" (Japanese) on the au homepage regarding
the following.
•OpenSSL License
From a PC:
( http://www.au.kddi.com/support/mobile/guide/manual/)

Cell phone and PHS operators collect and
recycle unused telephones, batteries and
battery chargers at stores bearing the 
logo regardless of brand and manufacturer
to protect the environment and reuse
valuable resources.
Soldby: KDDICORPORATION,
 OKINAWACELLULARTELEPHONECOMPANY
Manufacturedby:KYOCERACorporation
Keitai Guarantee Service Center
For loss, theft or damage (toll free)
From fixed-line phones/au cell phones:
0120-925-919
Business hours: 9:00 to 21:00 (7 days a week)
For inquiries, call:
Customer Service Center
From fixed-line phones:
0077-7-113
From au cell phones:
113 area code not required
For service cancelation procedure in case of loss or theft (toll free)
In case above numbers are not available, call toll-free:
Business hours: 24 hours (7 days a week)
From fixed-line phones:
0077-7-111
From au cell phones:
157 area code not required
For general information, charges, and operation assistance (toll free)
Business hours: 9:00 to 20:00 (7 days a week)
0120-977-033 (except Okinawa)
0120-977-699 (Okinawa)
Pressing “zero” will connect you to an operator, after calling “157”
on your au cellphone.