Lidix CL-2 User manual

CL-2 Service Manual
Service Manual
For CL-2
Date. Rev. Notice.
2018.05 1.0
2018.12 1.2

CL-2 Service Manual
1. Please read this service manual, before test and
setting change of CL-2.
2. Follow this manual to prevent any
physical/material damage and operating safely
and solve the problem.
3. Reproduction, copying, or fabrication of any
information contained in this manual, without
prior consent of LIDIX, is forbidden.
2

CL-2 Service Manual < Contents >
1. SAFETY
1-1. Safety Information
1-2. Operational Environment
1-3. Installation/Moving
1-4. Maintenance/Checking
2. APPEARANCE
2-1. Machine Overview
2-2. Operation Panel Overview
2-3. Basic Operation
3. Counting mode
3-1. Value Mode
3-2. Fitness Mode
3-3. TITO Mode
3-4. Batch Mode
3-5. Report

CL-2 Service Manual < Contents >
4. User Setting
4-1. Function
4-2. Ex Device
4-3. UI Config
4-4. Pocket Size
4-5. Product Info
5. ENG Setting (Engineer setting)
5-0. Entering ENG setting
5-1. Count Adjustment
5-2. Motor Calibration
5-3. CIS Calibration
5-4. UV Sensor Calibration
5-5. US Calibration
5-6. MG Calibration
5-7. CF Level Settings
5-8. Fitness Level settings
5-9. ATM Fitness Level settings
5-10. Function Settings
5-11. LXS Data
5-12. TACO

CL-2 Service Manual < Contents >
6. Error Code
6-1. < ROI > error
6-2. < Value > Error
6-3. < IR > Error
6-4. < UV > Error
6-5. < MG > Error
6-6. < US > Error
6-7. < Unfit > Error
6-8. < SN > Error
6-9. < Counting Error > Error
6-10. < Etc > Error
7. Explode View
7-1. Frame Assy’
7-2. LOWER UNIT Assy’
7-3. UPPER UNIT Assy’
7-4. RC UNIT Assy’
7-5. SUB Assy’

CL-2 Service Manual < Contents >
8. Daily cleaning
9. Accessories & Specification

CL-2 Service Manual
1-1. Safety Information
Important safety symbols
7
These warnings and precautions are included in order to prevent injury to you and others, as well as preventing any potential damage to your
machine. Be sure to read and understand all of these instructions before using the machine.
Use common sense for operating any electrical appliance and whenever using your machine. Also, follow all warnings and instructions marked on
the machine and in the accompanying literature.
This section explains the meanings of all icons and signs in the user’ guide. These safety symbols are in order, according to the degree of
danger.
Warning : Hazards or unsafe practices that may result in severe personal injury.
Caution : Hazards or unsafe practices that may result in severe personal injury.
Do not attempt
Do not touch.
Do not disassemble.
Make sure the machine is grounded to prevent electric shock.
The power plug be pulled out before taking necessary action.
Follow directions explicitly.
Explanation of all icons and signs used in the user’s guide :

CL-2 Service Manual
1-2. Operational Environment
8
Warning
Do not use if the power cord is damaged or if the electrical outlet is not grounded.
►This could result in electric shock or fire.
Do not place anything on top of the machine (water, small metal or heavy objects, etc.).
►This could result in electric shock or fire.
Do not bend, or place heavy objects on the power cord.
►This could result in electric shock or fire.
Do not remove the plug by pulling on the cord; do not handle the plug with wet hands.
►This could result in electric shock or fire.
If the machine gets overheated, it releases smoke, makes strange noises, or generates an odd odor,
immediately turn off the power switch and unplug the machine.
►This could result in electric shock or fire.
Never operate the machine without the protective cover. The reflected beam, although invisible, can
damage your eyes.
►When using this product, these basic safety precautions should always be followed to reduce risk of
fire, electric shock, and injury to persons.

CL-2 Service Manual
1-2. Operational Environment
9
Caution
Be careful not to put your hand, hairs and clothes(including tie) when handling machine.
Do not forcefully pull the note out during counting.
►It can cause damage to the machine.
Be care when removing jammed notes.
►You may get injured.
Make sure the machine stops completely before opening the covers of the machine.
►Otherwise, there is a risk of an injury.
Do not disassemble the machine unless instructed in the user manual.
►It can damage the machine.
When removing jammed paper, do not use tweezers or sharp metal objects.
►It can damage the machine.
During an electrical storm or for a period of non-operation, remove the power plug from the electrical
outlet.
►This could result in electric shock or fire.

CL-2 Service Manual
1-3. Installation/Moving
10
Caution
Before moving the machine, turn the power off and disconnect the cord.
Make sure lift the machine using both hands.
►The machine could fall, causing injury or machine damage.
Do not place the machine on an unstable surface.
Make sure you plug into a grounded electrical outlet.
►Otherwise, this could result in electric shock or fire.
Do not overload wall outlets and extension cords.
►This can diminish performance, and could result in electric shock or fire.
Risk of explosion, if battery is replaced by an incorrect type
Dispose of used batteries according to the instructions

CL-2 Service Manual
1-4. Maintenance/Checking
11
Caution
Unplug this product from the wall outlet before cleaning the inside of the machine. Do not clean the
machine with benzene, paint thinner or alcohol; do not spray water directly into the machine.
►This could result in electric shock or fire.
When cleaning the machines, use dry cloth or cloth moistened with water. Do not pour the water onto
machine.
►It can cause damage to the machine.
When you are working inside the machine replacing supplies or cleaning the inside, do not operate the
machine.
►You could get injured.
Do not use air spray which contains flammable gas for cleaning.
►It may cause failure or a fire.
Do not disassemble, repair or rebuild the machine by yourself.
►It can damage the machine. Call a certified technician when the machine needs repairing.
Keep the power cable and the contact surface of the plug clean from dust or water.
►Otherwise, this could result in electric shock or fire.
Do not remove any covers or guards that are fastened with screws.
Fuse replacement should only be repaired by a certified service technician. Repair by non-certified
technicians could result in fire or electric shock.

CL-2 Service Manual
2-1. Machine Overview
12
1 Front Case 8 Rear Cover
2 Front Cover 9 Thickness Dial
3 Stacker 10 Interface Connector
4 Hopper guide 11 Inlet
5 Start/Stop Button (LEFT) + Power Button 12 Side Case R
6 Start/Stop + Print Button (RIGHT) 13 Side Case L
7 Touch LCD (GUI)
9
11
10
8
1
6
7
2
4
3
5
13
12

CL-2 Service Manual
2-2. Operation Panel Overview
Configuration
NO KEY FUNCTION
1 Power button.
2 Left Start / Stop Key to manual working.
NO KEY FUNCTION
3 Print Button.
4 Right Start / Stop Key to manual working.
13

CL-2 Service Manual
Screen Configuration
2-2. Operation Panel Overview
14
Count mode select button.
(Count / MIX / SP)
Currency select button.
Batch setting button.
Can set each count mode.
Report button to see the counting
detail information.
ADD function
Selecting Counting speed for each
function.
S/N function. (Available for specific currency.)
White letter -> Enabled / Red letter -> Disabled
Function button for use setting.
Pcs
Amount

CL-2 Service Manual
2-3. Basic Operation
15
STEP 1. Plug the power cord into the power receptacle.
STEP 2. Turn on CL-2 by pressing Power Switch.
STEP 3. Select the Currency
STEP 4. Select a Counting Mode.
STEP 5. Adjust Hopper guide to the notes to be counted.
STEP 6. Put the notes onto the Hopper, and counting starts automatically.
•Remarks
- Setting options will begin from next page. Please
- After changing the User Setting, press the icon to save the new setting, otherwise the setting
will remain unchanged

CL-2 Service Manual
3. Counting mode
16
3-1. Currency Setting
Mode Description
Currency You can choose Currency when you
click this button.

CL-2 Service Manual
3. Counting mode
17
3-2. Count Mode Setting
Mode Description
COUNT Count only Pcs.
MIX MODE It count the all denomination of
selected currency.
SP
Recognize of first note automatically
and count the same value
denomination.
TITO
TITO count function
(Planning to develop / Not available at
this moment)
Additional
Feature
Enable & Disable by Engineer setting.
MIX and SP mode can do below
additional function.
Face / Orient : Only count Face /
Orient direction.
Issue : Recognize first note
automatically and count the
note with same version.

CL-2 Service Manual
18
3-3. Batch Setting
Mode Description
Batch Setting
If you select the Batch function on the
screen, the Batch mode setting screen
will be Shown.
As you select the amount the
denominations will be assigned in the
pocket.
Customer You can freely change the Batch size
by pressing the Up and Down button.
Additional
Button
You can set batch size for each count
mode (Count / Mix / SP) by click this
red circled button.
3. Counting mode

CL-2 Service Manual
19
3-4. Report
If you select the Report function on the screen,
the Report screen will be shown on the screen.
Mode Description
NOW You can see the detail information of
last counted result.
ADD You can see the detail information of
added counted result.
OCR
You can see the serial number of the
counted notes. (Available for specific
currency.)
3. Counting mode

CL-2 Service Manual
4. Function Mode (User setting)
20
4. Function Mode (User setting)
Function mode is for the user setting.
You can set every category each subject.
Please refer the following manual.
4. Function Mode.