Lifescan novo nordisk InDuo User manual

Quick Reference Guide
See inside for instructions
on using InDuo™
Important:
Read detailed instructions
in your InDuo™ user manual

InDuo™ is designed to be used with:
•OneTouch®Ultra Test Strips
•OneTouch®Ultra Control Solution
•OneTouch®UltraSoft™ Adjustable
Blood Sampler
•OneTouch®UltraSoft™ Sterile Lancet
•OneTouch®UltraClear™ Cap for
alternate puncture site
•Penfill®3 ml insulin cartridges
•NovoFine®6 and 8 mm needles

CODING THE InDuo™ METER
Start with meter turned off.
Insert test strip to turn on meter.
All display segments will appear,
followed by code number.
Compare code number on meter
display with code number on
test strip vial. If matching, begin
testing.
If not matching, see Step 3.
Step 1 Enter code mode
Press Ñuntil codes match.
After the apply symbol R
appears, meter is ready for
testing.
Step 3 Code meter
Step 2 Match code numbers
Code meter before using it for first time and
every time you change to another vial of
OneTouch®Ultra test strips.

TEST SUMMARY
Note: Before testing, wash hands with warm, soapy
water. Rinse and dry thoroughly. See InDuo™ user
manual for important information on arm testing.
You can touch test strip
anywhere on its surface.
Once inserted, meter turns on
automatically.
Touch and hold blood drop to
top edge of test strip, where it
meets narrow channel. Hold
blood drop to top edge until
confirmation window is
completely filled before meter
begins to count down. If
window does not fill completely,
do not add blood to test strip.
Discard test strip and retest.
Accurate results in just 5 seconds.
Step 1 Insert test strip
Step 2 Apply sample
Step 3 Read results

DISPLAY SYMBOLS AND MESSAGES
A blood glucose test result with a
suggestion to check your ketone levels
Blood glucose level is higher than
33.3 mmol/L (600 mg/dL). Recheck glucose level
and if Scall your healthcare professional
immediately
Blood glucose level is lower than
1.1 mmol/L (20 mg/dL). Treat this condition
according to healthcare professional
recommendation
The temperature of the air, blood
glucose meter, or test strips was
below the operating range of
the InDuo™ meter (6°–44°C/43°–111°F)
The temperature of the air, blood
glucose meter, or test strips was
above the operating range of
the InDuo™ meter (6°–44°C/43°–111°F)
Battery power is getting low.
You can complete about 50 more tests
from the time this symbol first appears

DISPLAY SYMBOLS AND MESSAGES
Error message that indicates that there is
a problem with the InDuo™ meter*
1. New meter not coded.
Code meter. Or;
2. Meter lost power briefly and entered setting
mode. Reset meter code. If after resetting
and coding the meter, Q still appears,
call the InDuo™ Customer Care Line at
1 888 729-2299. Possible meter memory
problem; do not use 14- and 30-day
averages
Battery power is too low to run a test.
Replace the battery immediately
The time flashing on the display indicates
the meter lost power briefly and entered
setting mode. Reset time, time format, date
and most importantly, unit of measure
(mg/dL or mmol/L) as necessary. Typically, in
Canada, you would use mmol/L. After setting
meter, insert a new test strip. If Qappears,
reset meter code.
Test results stored in the meter memory may
not be in the order in which they were
performed. Do not rely on 14- and 30-day
averages. Call the InDuo™ Customer Care
Line at 1 888 729-2299

DISPLAY SYMBOLS AND MESSAGES
Error message could be caused by a used
test strip or indicates a temporary or
permanent electronics problem*
Error message. The blood or control
solution sample was applied before R
appeared on the display*
Three possible reasons:
1. Possible high glucose in a test
environment near low end of operating
temperature range (6°–44°C/43°–111°F).
Retest in a warmer environment. Or;
2. Test strip damaged or moved during
testing. Repeat test with new test strip.
Or;
3. Sample improperly applied. Review
blood application and repeat test with
new test strip.
Test strip damaged or confirmation
window not full*
*Retest with a new test strip. If the problem
persists, call the InDuo™ Customer Care Line
at 1 888 729-2299.

Pull out the InDuo™ insulin
doser. If the insulin is a
suspension (cloudy insulin) you
must re-suspend the insulin as
described in the Penfill®
package insert.
Attach a NovoFine®6 or 8 mm
needle.
To prime the InDuo™ insulin
doser, press the release button
(the push button will jump out).
Dial 1 unit. (For new Penfill®
dial 8 units). Hold the insulin
doser with the needle pointing
upwards and press the push
button completely in. Repeat
the procedure until a drop of
insulin appears.
MAKING AN INJECTION
Step 1 Prepare the doser
Step 2 Prime the doser

Follow the injection method
recommended by your
healthcare professional.
Press the push button
completely in until it locks.
After the injection, discard the
needle carefully.
Always replace the insulin doser
into the meter cap.
Press the release button and the
push button jumps out.
Dial the number of units you
need.
Step 3 Dial the dose
Step 4 Inject the insulin

CHECKING YOUR PREVIOUS INJECTION
Pull out the InDuo™ insulin
doser. The display shows your
previous dose and the time
passed since delivery.
Example 1
You injected 6 units
2 hours ago.
Example 2
You injected 70 units
10 hours ago.
Example 3
You injected 18 units
6 hours ago.
Step 1 Look at the display