Light Emotion COB150RGBW Operator's manual

www.lightemotion.com.au
COB150RGBW
150W COB LED 4-in-1 RGBW Wash
User’s instruction manual
This manual contains important information about the safe installation and use of this product
Please read this instruction manual carefully before installing or operating
Please keep these instructions in a safe place for future reference
V1.01

1
Contents
1. Safety Instructions 2
2. Installation 3
3. Features 3
4. Operation 3
Menu Functions 4
Explanations 5
5. DMX Profile Charts 7
5A. Colour Macro Chart 11
6. DMX Connections 12
7. DMX Address Setting 12
8. DMX Terminator 12
9. Cleaning and Maintenance 13
10. Technical Data 13
11. Warranty 13

2
Introduction
Thank you for the purchase of your COB150RGBW COB LED 150W RGBW Wash Fixture by Light Emotion. We
are confident you will be satisfied with your purchase and enjoy many years of use from this Professional Light
Emotion product. Please read these instructions carefully to ensure the product is well look after and used correctly
to avoid any potential problems.
Please note that as part of our ongoing commitment to continuous improvement and product development, the
specifications in this manual are subject to change without notice. Whilst every care has been taken in the
preparation of this manual we reserve the right to change specifications in the course of product improvement.
What is in the box:
- 1 x COB150RGBW fixture
- Power cable
- 40 and 80 degree lens
- This user manual
1. Safety Instructions:
Please read these instructions carefully. It includes important information about the installation usage and
maintenance of this product.
- Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
- Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is
not higher than that stated on the sticker of the fixture.
- This product is intended for indoor use only. To prevent risk of fire or shock, do not expose fixture to rain or
moisture.
- Make sure there are no flammable materials close to the unit while operating.
- The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surface. Be sure that
no ventilation slots are blocked.
- Always disconnect from power source before servicing.
- Secure fixture to stands, trussing and the like using a safety chain.
- Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than this.
- In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized
technical assistance centre.
- Make sure power cord is never crimped or damaged.
- Never disconnect power cord by pulling or tugging on the cord.
- Never carry the fixture directly from the cord. Carry by holding the unit directly or via the hanging bracket.
- Avoid direct eye exposure to the light source while it is on.

3
2. Installation:
Caution: For safe mounting of this product, please read the following carefully.
- Use a suitable clamp to attach to lighting stand, trussing or bar, together with safety chain.
- When mounting the product, do not stand directly underneath the product
- Always use a safety chain when mounting the product on stands, trussing or bars. Make sure the breaking strain
rating of the chain is at least 10 times the weight of the product.
- Make sure there is adequate ventilation around the product.
- Never look directly into the LED light or laser sources of the product.
- For indoor use only – do not use outdoors.
- To avoid electrical shock, keep away from rain and moisture.
3. Features
This product is designed as entertainment effect lighting fixture and is only intended to be used as an effect for
entertainment and production applications. Due to our ongoing commitment to constantly reviewing and improving
products, features and specifications are subject to change without prior notice.
It features 1 150W COB LED RGBW 4-in-1 which is a single LED source designed to be very bright. Being 4-in-1,
the user has complete control over colours which emit from the one lens reducing any possibility of colour ghosting
that can occur with fixtures that use individual red, green, blue and white LEDs.
This unit has built-in protection which will shut off the unit should its internal temperature reach 85 degrees C. This
protects the internal electronics and components from damage caused by over heating.
- Power input: AC 100V-240V/50HZ-60HZ
- Wattage: 132W
- LEDs: 1 pc 150W COB LED (RGBW 4 in 1)
- Beam angle of LEDs: 80 degree, or 40 degree with interchangeable lens included
- 3-pin female XLR socket and 3-pin male XLR socket
- Built-in microphone
- Four button LED digit display
- Fuse: M250 3A slow blow
- Maximum 5 fixtures can be daisy chained together for power (DMX technically unlimited)
- Weight: 4.1 kg
- Size: 415x245x192mm
4. Operation
The COB150RGBW has 7 kinds of operation mode which are as follows:
Manual dimmer colour mode, Sound active mode, Auto-run program mode, Static colour
select mode, Other program select mode, Slave mode, DMX mode

4
The modes of operation are selected using the MODE button. Pressing the MODE button repeatly
will reach positions as per the table below. Then press SET UP followed by UP / Down to access
the attributes of each mode.
When you are using the MODE / SET UP / UP / DOWN LED display, the unit will lock the display
if there is no input over 30 seconds. To unlock, press and hold down MODE button for 3 seconds
before gaining access to the units menu options.
MODE manual SET UP manual UP/DOWN manual Instruction
DMX MODE
Address ~ Sets the DMX starting address
Channels
The unit occupies 3 DMX channels
The unit occupies 4 DMX channels
The unit occupies 5 DMX channels
The unit occupies 6 DMX channels
The unit occupies 9 DMX channels
NO DMX mode When DMX signal is lost or interrupted,the unit
will default to BLACKOUT option.It will switch all
LED’s off
When DMX signal is lost or interrupted,the unit
will default to HOLD option.It will hold the last
state before signal was lost.
When DMX signal is lost or interrupted,the unit
will default to AUTO option.It will run the internal
programs.
SLAVE MODE Slave mode
Set the unit into slave mode
DIMMER
MODE
Red dimmer ~ Adjust the intensity of the red colour
Green dimmer ~ Adjust the intensity of the green colour
Blue dimmer ~ Adjust the intensity of the blue colour
White dimmer ~ Adjust the intensity of the white colour
Flash ~ Adjust the flash speed, is flash
off, is slowest, is fastest
SOUND MODE
Mode select ~ Select the 16 built-in sound modes
Sensitivity select ~ Adjust the sensitivity of the sound-active,
is the lowest level, is the highest level
AUTO
RUN
MODE
Dreaming mode set ~ Select the 16 built-in dreaming mode
Jumping mode set ~ Select the 16 built-in jumping mode
Auto
Dreaming&Jumping
mode
Set the light in auto dreaming&jumping mode,the
dreaming mode and jumping mode will run in a
continuous cycle
Speed set ~ Adjust the speed of the dreaming/jumping mode
STATIC
COLOUR
SELECT MODE
Colour select ~ Select the 64 static colours
Flash ~ Adjust the flash speed, is flash
off, is slowest, is fastest

5
OTHER
MODE
Display
on/off
LED digital tube display always on
LED digital tube display off
Display
normal/inverse
LED digital tube display normal
LED digital tube display inversion
Initialization mode
Initialize the unit at the extra factory setting
A. Manual dimmer colour mode
1) Manual dimmer colour select
Press "MODE" button, select the manual dimmer colour select mode .At this time, the four digital
tube displays red " ~ ", press the "SET UP" to choose different colour, green
" ~ ", blue " ~ ", white " ~ ", then press "UP" or
"DOWN" button to set the dimming rate 0-255.
2) Flash speed select
Press "SET UP" to choose the flash speed select mode .At this time, the four digital tube displays
" ~ ". Press "UP" or "DOWN" button to select the flash speed 00-15, 00 is flash
off, 01 is the slowest flash speed, 15 is the fastest flash speed.
B. Sound active mode
Press "MODE" button, select the sound active program mode. There are two modes in the sound
active program mode. You can select them by pressing the "SET UP" button.
1) Sound active program mode select
Press "SET UP" button until the four digital tube displays " ~ ", then press "UP" or
"DOWN" to select the sound active program mode 1-16 under this mode.
2) Sensitivity select mode
Press "SET UP" button until the four digital tube displays" ~ ", then press "UP" or
"DOWN" to select the sound active the sensitivity 1-8. 1 is off sound-active, 2 is the lowest
sensitivity, 8 is the highest sensitivity.
C. Auto-run program mode
Press "MODE" button, select the auto-run program mode. There are three modes in the auto-run
program mode. You can select them by pressing the "SET UP" button.
1) Colour dreaming program mode select
Press "SET UP" button until the four digital tube displays " ~ ", then press "UP" or
"DOWN" button to select the sixteen colour dreaming programs 1-16.
2) Colour jumping program mode select
Press "SET UP" button until the four digital tube displays " ~ ", then press "UP" or

6
"DOWN" button to select the sixteen colour jumping programs 1-16.
3) Colour dreaming/jumping speed select
Press "SET UP" button until the four digital tube displays " ~ ".Press "UP" or
"DOWN" button to select the colour dreaming/jumping speed 01-16, 01 is the slowest speed, 16 is
the fastest speed.
D. Static colour select mode
Press "MODE" button, select the static colour select mode. There are two modes in static colour
select mode. You can select them by pressing the "SET UP" button.
1) Static colour select
Press "SET UP" button until the four digital tube displays " ~ ", then press "UP" or
"DOWN" to select static colour 0-64 under this mode.
2) Flash speed select
Press "SET UP" button until the four digital tube displays " ~ ", then press "UP" or
"DOWN" button to select the static colour flash speed 00-15, 00 is flash off, 01 is the slowest flash
speed, 15 is the fastest flash speed.
E. Other program select mode
1) Display off/on select mode
Press “SET UP” button , select display off/on mode. Press UP or DOWN to select the four digital
tube display on/off. When the digital tube displays " " means that the display will on in any
situation, when the digital tube displays " " means that the display will be automatically off
after 60 seconds if there is no operation.
2) Display normal/inversion select mode
Press “SET UP” button, select display normal/inversion mode. Press UP or DOWN to select the
four digital tube display normal/inverse. When the digital tube displays " " means that the
digital tube displays normally, when the digital tube displays" "means that the digital tube
displays inversion.
3) Initialization select mode
Press “SET UP” button until the four digital tube displays " ", and the display is flicker.
Now press UP button and DOWN button at the same time, you can initialize it at extra factory
setting, running on the first colour jumping mode, and the four digital tube displays " ".
F. Slave mode
Press "MODE" button, select salve mode. At this time, the four digital tube displays " ”.
Press SET UP,UP or DOWN is no use under this mode.

7
G. DMX mode
You can control the devices individually via your DMX-controller.
1) DMX address select mode
The control Board allows you to assign the DMX address which is defined as the first channel of
the COB LED par. Press
“ MODE ” button until the display is “ ~ ” , then press UP
or DOWN to set the DMX address. The four digital tube display will be flicker when there is no
controller signal.
2) DMX-PROTOCOL
Press “ SET UP ” button until the display is “ / / / / ” ,
then press UP or DOWN to set the desired channels (3,4,5,6,9). There are total 5 DMX modes.
3) No DMX mode set
Press "SET UP" button until the four digital tube displays " ", then press "UP" or "DOWN"
to select the 3 no DMX modes. When the digital tube display " ", it means when DMX
signal is lost or interrupted, the unit will default to BLACKOUT option, it will switch all LED’s off;
when the digital tube display " ", it means when DMX signal is lost or interrupted, the unit
will default to HOLD option, it will hold the last state before signal was lost; when the digital tube
display " ", it means when DMX signal is lost or interrupted, the unit will default to AUTO
option, it will run the internal programs.
5. DMX Charts
: 3 channels mode
Channel Value Function
1 Colour Macros 0-255 See Colour Macros Chart
2 Strobe Channel 0-31
32-63
64-95
96-127
128-159
160-191
192-223
224-255
LED OFF
LED ON
STROBE SLOW->FAST
LED ON
STROBE PULSE SLOW->FAST
LED ON
RANDOM STROBE SLOW->FAST
LED ON
3 Master dimmer channel 0-255 Dimming 0% - 100%

8
: 4 channels mode
Channel Value Function
1 0-255 RED 0% - 100%
2 0-255 GREEN 0% - 100%
3 0-255 BLUE 0% - 100%
4 0-255 WHITE 0% - 100%
: 5 channels mode
Channel Value Function
1 0-255 RED 0% - 100%
2 0-255 GREEN 0% - 100%
3 0-255 BLUE 0% - 100%
4 0-255 WHITE 0% - 100%
5 0-255 MASTER DIMMER 0% - 100%
: 6 channels mode
Channel Value Function
1 0-255 RED 0% - 100%
2 0-255 GREEN 0% - 100%
3 0-255 BLUE 0% - 100%
4 0-255 WHITE 0% - 100%
5
0-31
32-63
64-95
96-127
128-159
160-191
192-223
224-255
STROBE
LED OFF
LED ON
STROBE SLOW->FAST
LED ON
STROBE PULSE SLOW->FAST
LED ON
RANDOM STROBE SLOW->FAST
LED ON
6 0-255 MASTER DIMMER 0% - 100%

9
: 9 channels mode
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
Red Green Blue White Strobe Master
Dim
Mode Multiple Function Speed/S
en.
Red
0-255
(dim→
bright)
Green
0-255
(dim→
bright)
Blue
0-255
(dim→
bright)
White
0-255
(dim→
bright)
0-31
LED off
32-63
LED on
64-95
Strobe
slow->
fast
96-127
LED on
128-159
Strobe
pulse
slow->
fast
160-191
LED on
192-223
Random
Strobe
slow->
fast
224-255
LED on
Dim-
ming
0-255
(dim→
bright)
Standard
Dim
Mode
(0-51)
No Function
No
function
No
function
No
function
No
function
No
function
Colour
Macro
Mode
(Ch8)
(52-102)
Colour
Macros
(See Colour Macros Chart)
Colour
Jump
Mode
(Ch8)
103-153
0-15 Colour Jump 1
Internal
Prog
Speed
(0-255)
(slow→
fast)
(Ch8)
16-31 Colour Jump 2
32-47 Colour Jump 3
48-63 Colour Jump 4
64-79 Colour Jump 5
80-95 Colour Jump 6
96-111 Colour Jump 7
112-127 Colour Jump 8
128-143 Colour Jump 9
144-159 Colour Jump 10
160-175 Colour Jump 11
176-191 Colour Jump 12
192-207 Colour Jump 13
208-223 Colour Jump 14
224-239 Colour Jump 15
240-255 Colour Jump 16
Colour
Dream
Mode
(Ch8)
154-204
0-15 ColourDream 1
16-31 ColourDream 2
32-47 ColourDream 3
48-63 ColourDream 4
64-79 ColourDream 5
80-95 ColourDream 6
96-111 ColourDream 7
112-127 ColourDream 8
128-143 ColourDream 9
144-159 ColourDream10
160-175 Colour Dream 11
176-191 Colour Dream12
192-207 Colour Dream13
208-223 Colour Dream14