lightculture NEON MICRO ARC User manual

COLOUR CODE
WARM WHITE
3000 K +/- 175 K
BL-LS-4850-30-HB
NATURAL WHITE
4000 K +/- 275 K
BL-LS-4850-40-HB
COOL WHITE
5700 K +/- 300 K
BL-LS-4850-57-HB
ELECTRICAL & OPTICAL DATA VARIANCE +/- 10%
SOLD BY THE METRE
IES FILES AVAILABLE
HORIZONTAL BENDING
LIGHT DIRECTION
MINIMUM
BEND RADIUS
50mm
10
10
Actual product characteristics may vary. Light Culture Australia Pty Ltd reserves the right to improve, modify or update the product designs without prior notice.
[email protected] | www.lightculture.com.au
NEON MICRO ARC | HORIZONTAL BENDING | ELECTRICAL AND PHYSICAL INSTALLATION GUIDE
DO NOT TWIST THE LIGHT OR BEND
AGAINST THE LIGHT SURFACE
NEON MICRO ARC HORIZONTAL BEDING
CAN BE CURVED AS SHOWN BELOW
–Avoid bending LED Neon within the rst unit (units are
clearly marked with dashed lines on the sides of the
product)
–LED Neon can be bent up to the dened “minimum
bend radius” (50mm for Neon Micro Arc)
BENDING PARAMETERS
LIGHT SURFACE
01
02
0011
0022
50mm

Actual product characteristics may vary. Light Culture Australia Pty Ltd reserves the right to improve, modify or update the product designs without prior notice.
[email protected] | www.lightculture.com.au
–LED Neon must always be used in conjunction with a
certied Bright Light 24V DC power supply.
–Check the polarity of the connector before inserting the
front connector and switching on the mains power.
–To minimise voltage drop and ensure consistent light
output, position the power supply near to the power
feed end of the LED Neon, and keep the line as short as
possible.
–Ensure to add 20% buer when selecting a power supply.
–Ensure your maximum run per power feed adheres to the
guidelines; 10m when using a single connector, or 20m
when using both connectors (see specication sheet).
–Before making any cuts, installation, maintenance, or
connection, be sure the mains power is disconnected.
–If essential; cut and connect LED Neon correctly. Any
incorrect operation can cause damage.
–All connector joints must be connected correctly to
achieve connector IP rating.
NEON MICRO ARC | HORIZONTAL BENDING | ELECTRICAL AND PHYSICAL INSTALLATION GUIDE
WIRING DIAGRAM
POWER SUPPLY DIMMER
optional black wire: -
red wire: +
24V DC
–Ensure the supply cord is not subject to mechanical stress
–Keep 10–20mm distance between the end of the prole and the end mounting piece
–The bend angle should be less than 15 degrees when installing LED Neon into the prole by hand
PROFILE INSTALLATION REQUIREMENTS

Actual product characteristics may vary. Light Culture Australia Pty Ltd reserves the right to improve, modify or update the product designs without prior notice.
[email protected] | www.lightculture.com.au
–Avoid placing mechanical stress on the front connector cable
–Do not curl or bend the front connector cable with excessive force
–Avoid installing the prole less than 10mm from the end mounting piece
–Install the LED Neon into the prole in one direction, don’t let it bow in the middle
PULL
PROFILE INSTALLATION REQUIREMENTS
NEON MICRO ARC | HORIZONTAL BENDING | ELECTRICAL AND PHYSICAL INSTALLATION GUIDE

TOP END FEED END CAP
01 02
WHITE - VERTICAL & HORIZONTAL BENDING BL-LS-4851 BL-LS-4852 BL-LS-4854
13m m
30m m
6m m
10.7m m
13m m
30m m
6m m
10.5m m
TOP END END CAP
Actual product characteristics may vary. Light Culture Australia Pty Ltd reserves the right to improve, modify or update the product designs without prior notice.
[email protected] | www.lightculture.com.au
FEED CONNECTOR SUPPLIED AS 1M CABLE
DOUBLE POWER FEED: FEED 01 + FEED 02
NEON MICRO ARC | CONNECTIONS
SWIVEL CONNECTIONS - IP20
SIDE FEED BOTTOM
FEED
TOP END
FEED
END CAP
WHITE - VERTICAL & HORIZONTAL BENDING
REQUIRES FITTING AT FACTORY. LEAD TIMES
APPLY
FEED CONNECTORS SUPPLIED AS 1M
CABLE STANDARD, CHECK FOR ALTERNATE
LENGTHS
SLIMLINE INJECTION MOULDING CONNECTIONS - IP67
SIDE END
TOP END
BOTTOM END
16mm
2m m
mm8
10mm
Φ1 2m m
mm21
11mm
13mm
12mm
12mm 12mm
16mm
2m m
8m m
11mm
11mm
13mm
13mm
16mm
2m m 10mm
12mm
m21 m
11mm
11mm
11mm
13mm
8m m
16mm
3m m 10mm
12mm
11mm
11mm
13mm
END CAP

Actual product characteristics may vary. Light Culture Australia Pty Ltd reserves the right to improve, modify or update the product designs without prior notice.
[email protected] | www.lightculture.com.au
CODE ACCESSORY L1 L2 HOLE
DIMENSIONS
HOLE
NUMBER
BL-LS-4858 PLASTIC AND ALUMINIUM PROFILE 2M 100mm 200mm Ø3.5mm 10
BL-LS-4855 PLASTIC AND ALUMINIUM MOUNTING CLIP 35MM 17.5mm -Ø3.5mm 1
L1 L2
14
14.7
PLASTIC AND ALUMINIUM
PROFILE 2M / CLIP
NEON MICRO ARC | MOUNTING ACCESSORIES