LIGHTINC FLAT-PAR 7 RGB-WW User manual

FLAT-PAR 7 RGB-WW
MANUAL
www.light-inc.nl
AFFORDABLE AND
COMPACT LED PAR
ATTACHABLE MAGNETIC
FROST FILTER
BRIGHT RGBW
LED’S
STATIC LIGHT

THANK YOU FOR PURCHASING OUR PRODUCTS
Every unit has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the
outer and inner packaging for damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit have arrived
intact. In case damage has been found or parts are missing, please contact the distributor or your dealer for further
instructions. Do not return this unit to your dealer without rst contacting them.
1. SAFETY INFORMATION
Before operating this unit, please carefully read this manual and keep for usage in the future. It is
necessary to respect the following rules.
Disposal of the device after its life cycle can damage the environment. Take it to a recycling company or
return it to the authorized dealer.
The products referred to in this manual conform to the guidelines of the European Community and are
therefore marked with the CE logo.
Keep this device away from children and unauthorized users. The dealer is not liable for damage as a result
of ignoring the information in this manual and incorrect operation.
Before operating this unit, please make sure the housing is in good condition and ensure pan and tilt can
rotate in full range.
0.5 m
Ensure that a minimum distance of 0.5 m is maintained between the xture and any ammable material.
The device can only function with 100-240v voltage, 50 / 60Hz power. Do not connect to any other power
supply. Disconnect the device from the power supply before opening it or before maintenance.
Never look directly into the projecting lens when the xture is switched on. The light can cause epileptic
seizures in light-sensitive people or people with epilepsy. Extreme caution and compliance with these
safety instructions are required, especially with beam effects.
Do not place or install the device on a surface that is exposed to vibration or any movement.
-15°C +45°C
The device should operate in temperature range -15 °C and + 45 °C. Do not use the device if the
temperature exceeds this range.
The lens shield must be replaced if it is broken. Never use the device if the shield is not fully closed.
Safety I class device must be earthed.
When the xture is mounted overhead, the safety rope must be attached to the correct mounting location
on the bottom of the device.
Please note that damage caused by manual changes to the device is not covered by the warranty.
If possible, recycle all packaging material.
2. DISPLAY INFORMATION
Menu Value Description
4CH D001 D001-D512
8CH A001 A001-A512 DMX address setting
R001 R000-R255 Red (0%--100%) from dark to bright
G001 G000-G255 Green (0%--100%) from dark to bright
B001 B000-B255 Blue (0%--100%) from dark to bright
U001 U001-U255 White (0%--100%) from dark to bright
FH 01-99 Strobe from slow to fast
CL 01-08 Static color 1-8
CC 01-99 Jump color from slow to fast
DE 01-99 Gradient color from slow to fast
CP 01-99 Color effect from slow to fast
SOUD 01-9 Sound control from slow to fast
3. DMX CHART
Channel Value Function
CH1 0--255 Dimmer 0-100%
CH2 0--255 Red dimmer, from dark to bright
CH3 0--255 Green dimmer, from dark to bright
CH4 0--255 Blue dimmer, from dark to bright
CH5 0--255 White dimmer, from dark to bright
CH6 0-255 Strobe from slow to fast
CH7
0--50 No function
51--100 Static color
101--150 Color jump change
151--200 Color pulse change
201--250 Color gradient
251-255 Sound control
CH8 0-255 Speed from slow to fast (speed master channel 7)
Channel Value Function
CH1 0--255 Red Dimmer 0-100%
CH2 0--255 Green Dimmer 0-100%
CH3 0--255 Blue Dimmer 0-100%
CH4 0--255 White Dimmer 0-100%

4. CONNECTION OF DMX-512
Connect XLR-XLR control wire with every light from the output of DMX.
XLR connection:
ATTENTION: Please connect one circle circuit plug on the output signal of last unit. This circle circuit plug must
be connected with a 120ohm resistance between terminals 2 and 3 of the CANON plug, connecting this circle
circuit plug can avoid the signal ashing phenomena of signal DMX512 during the transmission.
5. PROBLEM SOLVING
Problem Check List Trouble Shooting
The xture doesn’t work. 1. Does your xture get power? Make sure the xture is plugged in and power is on.
2. Check whether the fuse is broken. Replace the fuse.
LED dimmed. Check the voltage output is the same as
the input of the machine. Make sure the voltage output and input is correct.
No DMX input.
1. Is the polarity is opposite in the
DMX controller? Correct the DMX polarity.
2. Is it in DMX mode? Change to the DMX mode.
3. Are there 2 masters in a loop? Set one unit in Slave mode.
Unit shows unregular behavior. Is the DMX address correct on the Par
Light display? Set the right DMX address.
6. SPECIFICATIONS
• Voltage: AC100-240V • Channel: 8CH/4CH
• Frequency: 50Hz-60Hz • IP rate: IP20
• Consumption: 105W • Mode of control: DMX512 control, auto, sound control.
• Lamp: 7pcs*15W RGB+WW
4in1 LED
• Gross weight: 0.99KG
7. NOTES

ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
BSL B.V. | SPAARPOT 19 | 5667 KV GELDROP | THE NETHERLANDS
[phone]
WWW.BSL-LIGHTING.COM | WWW.LIGHT-INC.EU